2014-2019 Hiace · Service Manual TRANSMISSION

P0705/C2 Transmission Range Sensor Circuit Malfunction (PRNDL Input)

Diagnostic trouble codes · Vehicles built from Oct 2014

DESCRIPTION

The park/neutral position switch detects the shift lever position and sends signals to the TCM.
DTC No.
DTC Detection Condition
Trouble Area
P0705/C2
Any 2 or more signals of the following are ON simultaneously.
(2-trip detection logic)
  1. NSW input signal is ON
  2. R input signal is ON
  3. 3 input signal is ON
  4. 2 input signal is ON
  5. L input signal is ON
  1. Open or short in park/neutral position switch circuit
  2. Park/neutral position switch
  3. TCM

MONITOR DESCRIPTION

These DTCs indicate a problem with the park/neutral position switch and the wire harness in the park/neutral position switch circuit.
The park/neutral position switch detects the shift lever position and sends a signal to the TCM.
For security, the park/neutral position switch detects the shift lever position so that engine can be started only when the shift lever is in the P or N position.
The park/neutral position switch sends a signal to the TCM according to the shift position (P, R, N, D, 3, 2 or L).
The TCM determines that there is a problem with the switch or related parts if it receives more than 1 position signal simultaneously. The TCM will turn on the MIL and store the DTC.

WIRING DIAGRAM

C301982E01

INSPECTION PROCEDURE


DATA LIST

HINT:
Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the intelligent tester to the DLC3.

  4. Turn the ignition switch to the ON position.

  5. Turn on the tester.

  6. Select the item "Enter / Powertrain / ECT / Data List".

  7. Follow the instructions on the tester and read the Data List.

    Item
    Measurement Item/
    Range (display)
    Normal Condition
    Diagnostic Note
    Neutral Position SW Signal
    PNP SW Status/
    ON or OFF
    Shift lever is:
    1. On P or N: ON
    2. Not on P or N: OFF
    When the shift lever position displayed on the intelligent tester differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect.
    Shift SW Status (P Range)
    PNP SW Status/
    ON or OFF
    Shift lever is:
    1. On P: ON
    2. Not on P: OFF
    Shift SW Status (R Range)
    PNP SW Status/
    ON or OFF
    Shift lever is:
    1. On R: ON
    2. Not on R: OFF
    Shift SW Status (2 Range)
    PNP SW Status/
    ON or OFF
    Shift lever is:
    1. On 2: ON
    2. Not on 2: OFF
    Shift SW Status (L Range)
    PNP SW Status/
    ON or OFF
    Shift lever is:
    1. On L: ON
    2. Not on L: OFF
    Shift SW Status (N Range)
    PNP SW Status/
    ON or OFF
    Shift lever is:
    1. On N: ON
    2. Not on N: OFF
    Shift SW Status (D Range)
    PNP SW Status/
    ON or OFF
    Shift lever is:
    1. On D or 3: ON
    2. Not on D or 3: OFF
    Shift SW Status (3 Range)
    PNP SW Status/
    ON or OFF
    Shift lever is:
    1. On 3: ON
    2. Not on 3: OFF


1. INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

  1. C130119E27
    Jack up the vehicle.

  1. Disconnect the park/neutral position switch connector.

  1. Measure the resistance when the shift lever is moved to each position.

    Standard resistance:
    Tester Connection
    Shift Position
    Specified Condition
    4 (B) - 5 (L)
    P or N
    Below 1 Ω
    Except P or N
    10 kΩ or higher
    2 (RB) - 6 (PL)
    P
    Below 1 Ω
    Except P
    10 kΩ or higher
    2 (RB) - 1 (RL)
    R
    Below 1 Ω
    Except R
    10 kΩ or higher
    2 (RB) - 9 (NL)
    N
    Below 1 Ω
    Except N
    10 kΩ or higher
    2 (RB) - 7 (DL)
    D or 3
    Below 1 Ω
    Except D or 3
    10 kΩ or higher
    2 (RB) - 3 (2L)
    2
    Below 1 Ω
    Except 2
    10 kΩ or higher
    2 (RB) - 8 (LL)
    L
    Below 1 Ω
    Except L
    10 kΩ or higher



NG
REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY
OK


2. INSPECT SHIFT LOCK CONTROL UNIT ASSEMBLY

  1. C161983E07
    Connect the park/neutral position switch connector.

  1. Disconnect the transmission control switch connector of shift lock control unit assembly.

  1. Measure the resistance when the shift lever is moved to each position.

    Standard resistance:
    Tester Connection
    Shift Position
    Specified Condition
    1 (NSSD) - 2 (AT3)
    3
    Below 1 Ω
    1 (NSSD) - 2 (AT3)
    D
    10 kΩ or higher



NG
REPLACE SHIFT LOCK CONTROL UNIT ASSEMBLY
OK


3. CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - TCM)

  1. C301994E01
    Connect the transmission control switch connector of shift lock control unit assembly.

  1. Turn the ignition switch to the ON position, and measure the voltage when the shift lever is moved to each position.

    Standard voltage:
    Tester Connection
    Shift Position
    Specified Condition
    O1-12 (NSW) - Body ground
    P or N
    Below 2 V
    Except P and N
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - TCM)

  1. C301991E01
    Disconnect the TCM connector.

  1. Turn the ignition switch to the ON position, and measure the voltage when the shift lever is moved to each position.

    Standard voltage:
    Tester Connection
    Shift Position
    Specified Condition
    O1-13 (P) - Body ground
    P
    11 to 14 V
    Except P
    Below 1 V
    O2-9 (R) - Body ground
    R
    11 to 14 V*
    Except R
    Below 1 V
    O1-14 (N) - Body ground
    N
    11 to 14 V
    Except N
    Below 1 V
    O2-8 (D) - Body ground
    D or 3
    11 to 14 V
    Except D or 3
    Below 1 V
    O2-12 (3) - Body ground
    3
    11 to 14 V
    Except 3
    Below 1 V
    O2-11 (2) - Body ground
    2
    11 to 14 V
    Except 2
    Below 1 V
    O2-10 (L) - Body ground
    L
    11 to 14 V
    Except L
    Below 1 V

    HINT:
    *: The voltage will drop slightly due to the turning on of the back up light.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE TCM


← P0617 Starter Relay Circuit High (from Oct 2014)P0711 Transmission Fluid Temperature Sensor "A" Performance (from Oct 2014) →