2014-2019 Hiace · Service Manual TRANSMISSION

P0705 Transmission Range Sensor Circuit Malfunction (PRNDL Input)

Diagnostic trouble codes · Vehicles built Oct 2014 – Nov 2017

Versions by build date: Oct 2014 – Nov 2017 from Dec 2017

DESCRIPTION

The park/neutral position switch detects the shift lever position and sends signals to the ECM.
DTC No.
DTC Detection Condition
Trouble Area
P0705
Any 2 or more signals of the following are ON simultaneously (2-trip detection logic)
  1. NSW input signal is ON.
  2. R input signal is ON.
  3. 3 input signal is ON.
  4. 2 input signal is ON.
  5. L input signal is ON.
  1. Open or short in park/neutral position switch circuit
  2. Park/neutral position switch
  3. ECM

MONITOR DESCRIPTION

These DTCs indicate a problem with the park/neutral position switch and the wire harness in the park/neutral position switch circuit.
The park/neutral position switch detects the shift lever position and sends a signal to the ECM.
For security, the park/neutral position switch detects the shift lever position so that engine can be started only when the shift lever is in the P or N position.
The park/neutral position switch sends a signal to the ECM according to the shift position (P, R, N, D, 3, 2 or L).
The ECM determines that there is a problem with the switch or related parts if it receives more than 1 position signal simultaneously. The ECM will turn on the MIL and store the DTC.

WIRING DIAGRAM

C302038E02

INSPECTION PROCEDURE


DATA LIST

HINT:
Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the Intelligent Tester to the DLC3.

  4. Turn the ignition switch to the ON position.

  5. Turn on the tester.

  6. Select the item "Enter / Powertrain / Engine and ECT / Data List".

  7. Follow the instructions on the tester and read the Data List.

    Item
    Measurement Item/
    Range (display)
    Normal Condition
    Diagnostic Note
    Neutral Position SW Signal
    PNP SW Status/
    ON or OFF
    Shift lever position is:
    1. P or N: ON
    2. Except P or N: OFF
    When the shift lever position displayed on the intelligent tester differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect.
    Shift SW Status (P Range)
    PNP SW Status/
    ON or OFF
    Shift lever position is:
    1. P: ON
    2. Except P: OFF
    ↑
    Shift SW Status (R Range)
    PNP SW Status/
    ON or OFF
    Shift lever position is:
    1. R: ON
    2. Except R: OFF
    ↑
    Shift SW Status (2 Range)
    PNP SW Status/
    ON or OFF
    Shift lever position is:
    1. 2: ON
    2. Except 2: OFF
    ↑
    Shift SW Status (L Range)
    PNP SW Status/
    ON or OFF
    Shift lever position is:
    1. L: ON
    2. Except L: OFF
    ↑
    Shift SW Status (N Range)
    PNP SW Status/
    ON or OFF
    Shift lever position is:
    1. N: ON
    2. Except N: OFF
    ↑
    Shift SW Status (D Range)
    PNP SW Status/
    ON or OFF
    Shift lever position is:
    1. D or 3: ON
    2. Except D or 3: OFF
    ↑
    Shift SW Status (3 Range)
    PNP SW Status/
    ON or OFF
    Shift lever position is:
    1. 3: ON
    2. Except 3: OFF
    ↑


1. CHECK PARK/NEUTRAL POSITION SWITCH ASSEMBLY (POWER SOURCE)

  1. C294510E01
    Disconnect the park/neutral position switch connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    D37-2 (RB) - Body ground
    Ignition switch ON
    11 to 14 V
    D37-2 (RB) - Body ground
    Ignition switch off
    Below 1 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Park/Neutral Position Switch)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2. CHECK HARNESS AND CONNECTOR (NSW TERMINAL VOLTAGE)

  1. C294510E03
    Disconnect the park/neutral position switch connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    D37-4 (B) - Body ground
    Ignition switch ON
    11 to 14 V
    D37-4 (B) - Body ground
    Ignition switch off
    Below 1 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Park/Neutral Position Switch)



NG
Go to step 7
OK


3. INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

  1. C197712E54
    Disconnect the park/neutral position switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    4 (B) - 5 (L)
    Shift lever in P or N
    Below 1 Ω
    2 (RB) - 6 (PL)
    Shift lever in P
    Below 1 Ω
    2 (RB) - 1 (RL)
    Shift lever in R
    Below 1 Ω
    2 (RB) - 9 (NL)
    Shift lever in N
    Below 1 Ω
    2 (RB) - 7 (DL)
    Shift lever in D or 3
    Below 1 Ω
    2 (RB) - 3 (2L)
    Shift lever in 2
    Below 1 Ω
    2 (RB) - 8 (LL)
    Shift lever in L
    Below 1 Ω
    4 (B) - 5 (L)
    Shift lever not in P or N
    10 kΩ or higher
    2 (RB) - 6 (PL)
    Shift lever not in P
    10 kΩ or higher
    2 (RB) - 1 (RL)
    Shift lever not in R
    10 kΩ or higher
    2 (RB) - 9 (NL)
    Shift lever not in N
    10 kΩ or higher
    2 (RB) - 7 (DL)
    Shift lever not in D or 3
    10 kΩ or higher
    2 (RB) - 3 (2L)
    Shift lever not in 2
    10 kΩ or higher
    2 (RB) - 8 (LL)
    Shift lever not in L
    10 kΩ or higher

    Text in Illustration 
    *a
    Component without harness connected
    (Park/Neutral Position Switch)



NG
REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY
OK


4. INSPECT TRANSMISSION CONTROL SWITCH

  1. C301461E01
    Disconnect the transmission control switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 (NSSD) - 2 (AT3)
    Shift lever in 3
    Below 1 Ω
    1 (NSSD) - 2 (AT3)
    Shift lever in D
    10 kΩ or higher

    Text in Illustration 
    *a
    Component without harness connected
    (Transmission Control Switch)



NG
REPLACE TRANSMISSION CONTROL SWITCH (SHIFT LOCK CONTROL UNIT ASSEMBLY)
OK


5. CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - TRANSMISSION CONTROL SWITCH)

  1. C216021E07
    Disconnect the transmission control switch connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    H72-1 (NSSD) - Body ground
    1. Ignition switch ON
    2. Shift lever in D or 3
    11 to 14 V
    H72-1 (NSSD) - Body ground
    1. Ignition switch ON
    2. Shift lever not in D or 3
    Below 1 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Transmission Control Switch)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6. CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH, TRANSMISSION CONTROL SWITCH - ECM)

  1. C301464E01
    Disconnect the ECM connectors.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    D97-17 (P) - D97-105 (E1)
    1. Ignition switch ON
    2. Shift lever in P
    11 to 14 V
    D97-76 (R) - D97-105 (E1)
    1. Ignition switch ON
    2. Shift lever in R
    11 to 14 V*
    D97-99 (N) - D97-105 (E1)
    1. Ignition switch ON
    2. Shift lever in N
    11 to 14 V
    B71-47 (D) - D97-105 (E1)
    1. Ignition switch ON
    2. Shift lever in D or 3
    11 to 14 V
    D97-79 (3) - D97-105 (E1)
    1. Ignition switch ON
    2. Shift lever in 3
    11 to 14 V
    D97-78 (2) - D97-105 (E1)
    1. Ignition switch ON
    2. Shift lever in 2
    11 to 14 V
    D97-39 (L) - D97-105 (E1)
    1. Ignition switch ON
    2. Shift lever in L
    11 to 14 V
    D97-17 (P) - D97-105 (E1)
    1. Ignition switch ON
    2. Shift lever not in P
    Below 1 V
    D97-76 (R) - D97-105 (E1)
    1. Ignition switch ON
    2. Shift lever not in R
    Below 1 V
    D97-99 (N) - D97-105 (E1)
    1. Ignition switch ON
    2. Shift lever not in N
    Below 1 V
    B71-47 (D) - D97-105 (E1)
    1. Ignition switch ON
    2. Shift lever not in D or 3
    Below 1 V
    D97-79 (3) - D97-105 (E1)
    1. Ignition switch ON
    2. Shift lever not in 3
    Below 1 V
    D97-78 (2) - D97-105 (E1)
    1. Ignition switch ON
    2. Shift lever not in 2
    Below 1 V
    D97-39 (L) - D97-105 (E1)
    1. Ignition switch ON
    2. Shift lever not in L
    Below 1 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to ECM)

    HINT:
    *: The voltage will drop slightly due to the illumination of the back-up light.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM

7. CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM)
  1. Disconnect the D37 park/neutral position switch connector.

  1. Disconnect the B71 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D37-4 (B) - B71-25 (NSW)
    Always
    Below 1 Ω
    D37-4 (B) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM


← DIAGNOSTIC TROUBLE CODE CHART (from Dec 2017)P0705 Transmission Range Sensor Circuit Malfunction (PRNDL Input) (from Dec 2017) →