2014-2019 Hiace · Service Manual TRANSMISSION

P0724 Brake Switch "B" Circuit High

Diagnostic trouble codes · Vehicles built from Oct 2014

DESCRIPTION

The purpose of this circuit is to prevent the engine from stalling while driving in lock-up condition when brakes are suddenly applied.
When the brake pedal is depressed, this switch sends a signal to the ECM. Then the ECM cancels the operation of the lock-up clutch while braking is in progress.
DTC No.
DTC Detection Condition
Trouble Area
P0724
The stop light switch remains ON even when the vehicle is driven in a STOP (less than 3 km/h (2 mph)) and GO (30 km/h (19 mph) or more) pattern 5 times. (2-trip detection logic).
  1. Short in stop light switch signal circuit
  2. Stop light switch
  3. ECM

MONITOR DESCRIPTION

This DTC indicates that the stop light switch remains on. When the stop light switch remains ON during "stop and go" driving, the ECM interprets this as a fault in the stop light switch and the MIL comes on and the ECM stores the DTC. The vehicle must stop (less than 3 km/h (2 mph)) and go (30 km/h (19 mph) or more) ten times for two driving cycles in order to detect a malfunction.

WIRING DIAGRAM

Click here.

INSPECTION PROCEDURE


1. READ VALUE USING DATA LIST (STP SIGNAL)
  1. DATA LIST

    HINT:
    Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

    1. Turn the ignition switch off.

    2. Connect the Intelligent Tester to the DLC3.

    3. Turn the ignition switch to the ON position.

    4. Turn on the tester.

    5. Select the item "Enter / Powertrain / Engine and ECT / Data List".

    6. Follow the instructions on the tester and read the Data List.

      Standard:
      Item
      Measurement Item/
      Range (display)
      Normal Condition
      Stop Light Switch
      Stop light SW Status/
      ON or OFF
      1. Brake Pedal is depressed: ON
      2. Brake Pedal is released: OFF

      NOTICE:
      In the table above, the conditions listed under "Normal Condition" are reference conditions. Do not depend solely on these reference conditions when deciding whether a part is faulty or not.



OK
Go to step 3
NG


2. INSPECT STOP LIGHT SWITCH ASSEMBLY

  1. E065594E75
    Remove the stop light switch assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Resistance:
    Switch position
    Tester Connection
    Specified Condition
    Switch pin free
    1 - 2
    Below 1 Ω
    Switch pin pushed in
    ↑
    10 kΩ or higher
    Switch pin free
    3 - 4
    10 kΩ or higher
    Switch pin pushed in
    ↑
    Below 1 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Stop Light Switch Assembly)



NG
REPLACE STOP LIGHT SWITCH ASSEMBLY
OK


3. CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - ECM)

  1. C197708E82
    Install the stop light switch assembly.

  1. Measure the voltage according to the value(s) in the table below when the brake pedal is depressed and released.

    Voltage:
    Condition
    Tester Connection
    Specified Condition
    Brake pedal is depressed
    B71-36 (STP) - Body ground
    10 to 14 V
    Brake pedal is released
    ↑
    Below 1 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to ECM)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM


← P0722 Output Speed Sensor Circuit No Signal (from Oct 2014)P0741 Torque Converter Clutch Solenoid Performance (Shift Solenoid Valve SL) (from Oct 2014) →