2014-2019 Hiace · Service Manual BODY

INSPECTION

Inspection · Vehicles built from Oct 2014


INSPECT OUTER MIRROR SWITCH ASSEMBLY (w/o Retract Mirror)

  1. Check the mirror select switch and mirror surface adjust switch.

    1. B367792E01
      Turn the mirror select switch to the L position.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance (for left side):
      Tester Connection
      Condition
      Specified Condition
      9 (VL) - 13 (B)
      11 (M+) - 12 (E)
      UP
      Below 1 Ω
      OFF
      10 kΩ or higher
      9 (VL) - 12 (E)
      11 (M+) - 13 (B)
      DOWN
      Below 1 Ω
      OFF
      10 kΩ or higher
      10 (HL) - 13 (B)
      11 (M+) - 12 (E)
      LEFT
      Below 1 Ω
      OFF
      10 kΩ or higher
      10 (HL) - 12 (E)
      11 (M+) - 13 (B)
      RIGHT
      Below 1 Ω
      OFF
      10 kΩ or higher

    3. Turn the mirror select switch to the R position.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance (for right side):
      Tester Connection
      Condition
      Specified Condition
      8 (VR) - 13 (B)
      11 (M+) - 12 (E)
      UP
      Below 1 Ω
      OFF
      10 kΩ or higher
      8 (VR) - 12 (E)
      11 (M+) - 13 (B)
      DOWN
      Below 1 Ω
      OFF
      10 kΩ or higher
      7 (HR) - 13 (B)
      11 (M+) - 12 (E)
      LEFT
      Below 1 Ω
      OFF
      10 kΩ or higher
      7 (HR) - 12 (E)
      11 (M+) - 13 (B)
      RIGHT
      Below 1 Ω
      OFF
      10 kΩ or higher

      If the result is not as specified, replace the outer mirror switch assembly.
      Text in Illustration 
      *1
      Mirror Select Switch
      *2
      Mirror Surface Adjust Switch
      *a
      Component without harness connected
      (Outer Mirror Switch Assembly)

  1. Check that the LED illuminates.

    1. B367793E01
      Apply battery voltage to the outer mirror switch assembly and check that the LED illuminates.

      OK:
      Measurement Condition
      Specified Condition
      Battery positive (+) - 6 (ILL+)
      Battery negative (-) - 16 (ILL-)
      LED illuminates

      If the result is not as specified, replace the outer mirror switch assembly.
      Text in Illustration 
      *a
      Component without harness connected
      (Outer Mirror Switch Assembly)


INSPECT OUTER MIRROR SWITCH ASSEMBLY (w/ Retract Mirror)

  1. Check the mirror select switch and mirror surface adjust switch.

    1. B246906E17
      Turn the mirror select switch to the L position.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance (for left side):
      Tester Connection
      Condition
      Specified Condition
      9 (VL) - 13 (B)
      11 (M+) - 12 (E)
      UP
      Below 1 Ω
      OFF
      10 kΩ or higher
      9 (VL) - 12 (E)
      11 (M+) - 13 (B)
      DOWN
      Below 1 Ω
      OFF
      10 kΩ or higher
      10 (HL) - 13 (B)
      11 (M+) - 12 (E)
      LEFT
      Below 1 Ω
      OFF
      10 kΩ or higher
      10 (HL) - 12 (E)
      11 (M+) - 13 (B)
      RIGHT
      Below 1 Ω
      OFF
      10 kΩ or higher

    3. Turn the mirror select switch to the R position.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance (for right side):
      Tester Connection
      Condition
      Specified Condition
      8 (VR) - 13 (B)
      11 (M+) - 12 (E)
      UP
      Below 1 Ω
      OFF
      10 kΩ or higher
      8 (VR) - 12 (E)
      11 (M+) - 13 (B)
      DOWN
      Below 1 Ω
      OFF
      10 kΩ or higher
      7 (HR) - 13 (B)
      11 (M+) - 12 (E)
      LEFT
      Below 1 Ω
      OFF
      10 kΩ or higher
      7 (HR) - 12 (E)
      11 (M+) - 13 (B)
      RIGHT
      Below 1 Ω
      OFF
      10 kΩ or higher

      If the result is not as specified, replace the outer mirror switch assembly.
      Text in Illustration 
      *1
      Mirror Select Switch
      *2
      Mirror Surface Adjust Switch
      *a
      Component without harness connected
      (Outer Mirror Switch Assembly)

  1. Check the retract switch.

    1. B246906E18
      Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      13 (B) - 15 (MF)
      12 (E) - 14 (MR)
      Pushed in
      Below 1 Ω
      12 (E) - 15 (MF)
      13 (B) - 14 (MR)
      Not pushed in
      Below 1 Ω

      If the result is not as specified, replace the outer mirror switch assembly.
      Text in Illustration 
      *1
      Retract Switch
      *a
      Component without harness connected
      (Outer Mirror Switch Assembly)

  1. Check that the LED illuminates.

    1. B367484E01
      Apply battery voltage to the outer mirror switch assembly and check that the LED illuminates.

      OK:
      Measurement Condition
      Specified Condition
      Battery positive (+) - 6 (ILL+)
      Battery negative (-) - 16 (ILL-)
      LED illuminates

      If the result is not as specified, replace the outer mirror switch assembly.
      Text in Illustration 
      *a
      Component without harness connected
      (Outer Mirror Switch Assembly)

← REMOVAL (from Jan 2017)INSTALLATION (Oct 2014 – Dec 2014) →