2014-2019 Hiace · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built Oct 2014 – Dec 2016

Versions by build date: Oct 2014 – Dec 2016 from Jan 2017


1. DRAIN ENGINE COOLANT

A316990E01

CAUTION:
To avoid the danger of being burned, do not remove the reservoir cap while the engine and radiator assembly are still hot. Thermal expansion will cause hot engine coolant and steam to blow out from the radiator assembly.

  1. Loosen the radiator drain plug.

  1. Remove the reservoir cap.

  1. Loosen the cylinder block drain plug and drain the coolant.

  1. Tighten the radiator drain plug.

  1. Tighten the cylinder block drain plug.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf }


2. DRAIN ENGINE OIL

NOTICE:
  1. Prolonged and repeated contact with mineral oil will result in the removal of natural fats from the skin, leading to dryness, irritation and dermatitis. In addition, used engine oil contains potentially harmful contaminants which may cause skin cancer.
  2. Exercise caution in order to minimize the duration and frequency of skin contact with used oil. Wear protective clothing and gloves. Wash your skin thoroughly with soap and water, or use water-less hand cleaner to remove any used engine oil. Do not use gasoline, thinners, or solvents.
  3. In order to preserve the environment, used oil and the used oil filter must be disposed of only at designated disposal sites.

  1. Remove the oil filler cap.

  1. Remove the oil drain plug, and drain the oil into a container.

  1. Clean the drain plug, and install it with a new gasket.

    Torque:
    35 N*m{ 350 kgf*cm , 25 ft.*lbf }


3. REMOVE FRONT SEAT ASSEMBLY RH

  1. B107528
    Move the front seat assembly fully forward.

  1. Remove the 2 bolts on the rear side of the seat.

  1. Move the front seat assembly to the rearmost position.

  1. Remove the 2 bolts on the front side of the seat.

  1. Move the front seat assembly to the center of the seat slide rail. Set the seatback in the upright position.

  1. Disconnect the front seat inner belt assembly connector.

  1. Remove the front seat assembly.


4. REMOVE FRONT DOOR SCUFF PLATE RH

5. REMOVE ENGINE SERVICE HOLE SUB COVER SUB-ASSEMBLY
  1. Turn back the carpet, and remove the engine service hole cover sub-assembly.


6. REMOVE RADIATOR HOSE INLET

7. REMOVE RADIATOR HOSE NO.4

8. DISCONNECT WATER HOSE (for Heater)

9. REMOVE VANE PUMP V BELT

  1. A071310E01
    Loosen the bolt A and nut B, and remove the V belt.


10. REMOVE V (COOLER COMPRESSOR TO CRANKSHAFT PULLEY) BELT NO.1 (w/ Air Conditioning System)

  1. A074095E01
    Loosen the nut A and bolt B, and remove the V belt.


11. REMOVE FAN & GENERATOR V BELT (w/o Air Conditioning)

  1. A115631E01
    Loosen the bolts A and B, and remove the V belt.


12. REMOVE FAN & GENERATOR V BELT (w/ Air Conditioning System)

  1. A115632E01
    Loosen the bolts A and B.

  1. Loosen the adjusting bolt C, and remove the V belt.


13. REMOVE WATER PUMP PULLEY
  1. Remove the 4 nuts, fan spacer and fan pulley.


14. REMOVE VENTURI ASSEMBLY

  1. A111052E01
    Disconnect the throttle open switch connector.

  1. A111053E01
    Disconnect the throttle control motor connector.

  1. Remove the venturi and gasket.


15. SEPARATE COMPRESSOR AND MAGNETIC CLUTCH (w/ Air Conditioning System)
(Click here)

16. REMOVE COMPRESSOR MOUNTING BRACKET (w/ Air Conditioning System)

  1. A112014
    Remove the 3 bolts and compressor mounting bracket.

  1. A112016
    Remove the bolt and spacer.

  1. A112015
    Remove the 4 bolts and compressor mounting bracket.


17. REMOVE VANE PUMP DRIVE PULLEY

  1. C106133E01
    Using SST, remove the nut and the vane pump pulley.
    SST
    09960-10010   (09962-01000, 09963-01000)


18. REMOVE CRANKSHAFT PULLEY

  1. A058720E01
    Using SST, remove the pulley bolt.
    SST
    09213-54015   (91651-60855)
    09330-00021  

  1. A058719E01
    Using SST, remove the pulley.
    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05021)
    09950-60010   (09951-00490)
    09950-40011   (09957-04010)


19. REMOVE TIMING CHAIN OR BELT COVER SUB-ASSEMBLY

  1. A112017
    Remove the 11 bolts, washers, timing belt cover and 2 gaskets.


20. REMOVE TIMING BELT GUIDE
  1. Remove the timing belt guide.


21. SET NO.1 CYLINDER TO TDC/COMPRESSION

  1. A058728E01
    Using the crankshaft pulley bolt, align its groove with the timing pointer by turning the crankshaft clockwise.

  1. A058729E01
    Check that the timing marks of the camshaft timing pulley and No.2 timing belt cover are aligned.
    If not, turn the crankshaft 1 revolution (360°).


22. REMOVE TIMING BELT

  1. A058721E01
    Remove the timing belt.

    HINT:
    If reusing the timing belt, draw a direction arrow on the timing belt (in the direction of engine revolution), and place matchmarks on the pulleys and timing belt.

  1. A058730E01
    Turn the crankshaft 90° counterclockwise, and put the timing mark of the crankshaft timing pulley with the protrusion of the timing gear case.

    NOTICE:
    If the timing belt is disengaged, having the crankshaft timing pulley at the wrong angle can cause the piston head and valve head to come into contact with each other when you remove the camshaft timing pulley, causing damage. So always set the crankshaft pulley at the correct angle.

  1. A058731E01
    Loosen the timing belt idler No.1 bolt (A), and shift the idler to the left as far as possible.

  1. Temporarily tighten the pulley bolt (A), and then relieve the timing belt tension.

  1. Remove the timing belt.


23. REMOVE INJECTION PUMP DRIVE PULLEY

  1. A071313E01
    Using SST, remove the pulley nut.
    SST
    09213-14010   (91651-60865)
    09330-00021  

  1. A071314E01
    Using SST, remove the drive pulley.
    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05010, 09954-05021)


24. REMOVE INJECTION PUMP
  1. Disconnect the engine speed sensor connector.

  1. Disconnect the spill control valve connector.

  1. Disconnect the correction unit connector.

  1. Disconnect the timer control valve connector.

  1. Disconnect the fuel temperature sensor connector.

  1. Disconnect the engine wire clamp.

  1. Disconnect the 3 fuel hoses.

  1. A071318
    Disconnect the 3 bolts and injection pump stay No.1.

  1. Remove the 2 nuts and injection or supply pump assembly.


25. REMOVE TIMING BELT COVER NO.2
  1. Remove the 4 bolts and timing belt cover.


26. REMOVE WATER PUMP ASSEMBLY

  1. A031001
    Remove the 6 bolts and tension spring bracket.

  1. Remove the water pump and gasket.


27. REMOVE CAMSHAFT TIMING PULLEY

  1. A057443E02
    Set the No.1 cylinder to approx. 90° BTDC/compression.

    HINT:
    Set the No.1 cylinder to 90° BTDC/compression to avoid interference with the piston top and valve head.


    1. Using the crankshaft pulley bolt, turn the crankshaft 90° counterclockwise, and put the timing mark of the crankshaft timing pulley with the protrusion of the timing gear case.

  1. A056901E02
    Using SST, loosen the pulley bolt.
    SST
    09960-10010   (09962-01000, 09963-01000)

  1. A056903E02
    Using SST, separate the timing pulley from the camshaft.
    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05010, 09954-05021)

  1. Remove the pulley bolt and timing pulley.

  1. Remove the timing gear woodruff key.


28. REMOVE TIMING BELT IDLER SUB-ASSEMBLY NO.1

  1. A056838E01
    Remove the 2 bolts (A and B).

  1. Loosen the bolt (C), and remove the timing belt idler No.1.


29. REMOVE TIMING BELT IDLER SUB-ASSEMBLY NO.2
  1. Remove the bolt, timing belt idler No.2 and spacer.


30. REMOVE OIL PAN SUB-ASSEMBLY
  1. Remove the 16 bolts and 2 nuts.

  1. A057637E04
    Insert the blade of a oil pan seal cutter between the oil pan and cylinder block, and cut off applied sealer and remove the oil pan.

    NOTICE:
    1. Do not use a oil pan seal cutter for the timing belt case side and rear oil seal retainer.
    2. Be careful not to damage the oil pan flange.


31. REMOVE OIL STRAINER SUB-ASSEMBLY
  1. Remove the 2 bolts, 2 nuts, oil strainer, and gasket.


32. REMOVE TIMING GEAR CASE SUB-ASSEMBLY

  1. A056912
    Remove the 5 bolts, timing gear case, and gasket.

← COMPONENTS (from Oct 2014)REMOVAL (from Jan 2017) →