2014-2019 Hiace · Service Manual ENGINE

DISASSEMBLY

Removal / installation · Vehicles built from Oct 2014

NOTICE:
  1. When replacing the injectors (including shuffling the injectors between the cylinders), common rail or cylinder head, it is necessary to replace the injection pipes with new ones.
  2. When replacing the fuel supply pump, common rail, cylinder block, cylinder head, cylinder head gasket or timing gear case, it is necessary to replace the fuel inlet pipe with a new one.
  3. When replacing a fuel injector, check that the injection compensation codes of the fuel injectors installed on the cylinders match the ones registered in the ECM. If they do not match, correct the registered data (w/ DPF: Click here, w/o DPF: Click here).


1. REMOVE OIL FILLER CAP SUB-ASSEMBLY

2. REMOVE NOZZLE HOLDER SEAL

  1. A060180E01
    Using a small screwdriver, remove the 4 nozzle holder seals by prying between the holder seal and the cutout part of the cylinder head cover.


3. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

  1. A060180J01
    Using a small screwdriver, remove the nozzle holder seal by prying between the nozzle holder seal and the cutout part of the cylinder head cover.

  1. Disconnect the ventilation hose.

  1. A231937
    Remove the 10 bolts, 2 nuts, cylinder head cover and the cylinder head cover gasket.

  1. A289511
    Remove the 4 No. 3 cylinder head cover gaskets from the cylinder head cover.


4. REMOVE INJECTOR ASSEMBLY

  1. A076779E02
    Remove the union bolt, 4 injector hollow screws, 5 gaskets and nozzle leakage pipe.

    NOTICE:
    1. When removing the nozzle leakage pipe, place a cushion under the pipe.
    2. Be careful not to deform or scratch the union seal surface.
    3. After removing the fuel pipe, put it in a plastic bag to prevent foreign matter from contaminating its injector inlet.

  1. A076780E01
    Remove the 4 bolts, 4 washers, 4 No. 1 nozzle holder clamps and 4 injectors.

    HINT:
    Arrange the injectors, No. 1 nozzle holder clamps, washers and bolts in the correct order.

  1. Remove the O-ring from each injector.

  1. Remove the 4 injection nozzle seats from the cylinder head.


5. REMOVE CAMSHAFT TIMING PULLEY

  1. A100848
    Remove the bolt of the camshaft timing pulley while holding the camshaft with a wrench.

  1. A323634E02
    Using SST, remove the camshaft timing pulley and key.
    SST
    09950-40011   (09951-04010, 09952-04010, 09953-05010, 09957-04010)
    09955-04150  
    Text in Illustration 
    *a
    Hold
    *b
    Turn

  1. A100847E05
    Rotate the crankshaft approximately 90° counterclockwise from TDC to lower the piston.


6. REMOVE NO. 2 TIMING BELT COVER

  1. A051300E01
    Remove the nut, 4 bolts and No. 2 timing belt cover.


7. REMOVE CYLINDER BLOCK INSULATOR

  1. A149941
    Remove the cylinder block insulator from the cylinder head.


8. REMOVE NO. 2 CAMSHAFT

  1. A100849E02
    Position the key groove of the camshaft upward by turning the camshaft with a wrench.

  1. A100850E01
    Uniformly loosen the 15 bearing cap bolts in several steps in the sequence shown in the illustration and remove the bolts.

  1. Remove the 5 bearing caps.

  1. A051302E01
    Remove the No. 2 camshaft.


9. REMOVE CAMSHAFT

  1. A051303E01
    Remove the camshaft.


10. REMOVE CAMSHAFT SETTING OIL SEAL

  1. A243032
    Remove the oil seal from the camshaft.


11. REMOVE CYLINDER HEAD SUB-ASSEMBLY

  1. A059194E01
    Uniformly loosen the 18 cylinder head bolts in several passes in the sequence shown in the illustration. Then remove the 18 cylinder head bolts and 18 washers.

    NOTICE:
    Head warpage or cracking could result from removing the bolts in an incorrect order.

  1. Lift the cylinder head from the dowels on the cylinder block and place the cylinder head on wooden blocks on a workbench.

    NOTICE:
    Be careful not to damage the contact surfaces of the cylinder head or cylinder block.

    HINT:
    If the cylinder head is difficult to lift, use a screwdriver to pry between the cylinder head and block.


12. REMOVE CYLINDER HEAD GASKET

13. REMOVE WATER PUMP ASSEMBLY

  1. A100852
    Remove the 5 bolts, 2 nuts, water pump and gasket.


14. REMOVE TIMING GEAR COVER

  1. A262940E01
    Remove the 14 bolts and 2 nuts.
    Text in Illustration 
    *A
    w/ DPF
    *B
    w/o DPF

  1. A262941E01
    Pry the timing gear cover at the locations shown in the illustration and remove the timing gear cover.
    Text in Illustration 
    *A
    w/ DPF
    *B
    w/o DPF

    NOTICE:
    Be careful not to drop the injection gear.

  1. A239295
    w/ DPF:
    Remove the 3 O-rings from the timing gear case.

  1. A051310E01
    w/o DPF:
    Remove the O-rings from the timing gear case.


15. REMOVE INJECTION GEAR

  1. A102771
    Secure the No. 2 idle sub gear to the No. 1 idle gear with a service bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

    NOTICE:
    If the bolt hole of the No. 2 idle sub gear is not aligned with the bolt hole of the No. 1 idle gear, rotate the crankshaft counterclockwise to align the bolt holes. Then install the service bolt.

  1. A102772
    Remove the injection gear.


16. REMOVE NO. 1 CRANKSHAFT POSITION SENSOR PLATE

  1. A102774
    Remove the No. 1 crankshaft position sensor plate.


17. INSPECT BACKLASH OF OIL PUMP GEAR TO CRANKSHAFT TIMING GEAR

A060171E01
  1. Using a dial indicator, measure the backlash.

    Standard gear backlash:
    0.02 to 0.15 mm (0.0008 to 0.0060 in.)

    Maximum gear backlash:
    0.20 mm (0.0079 in.)

    If the gear backlash is more than the maximum, replace the gears as a set.


18. INSPECT NO. 1 IDLE GEAR THRUST CLEARANCE

A060169E01
  1. Using a dial indicator, measure the thrust clearance.

    Standard thrust clearance:
    0.06 to 0.11 mm (0.0024 to 0.0043 in.)

    Maximum thrust clearance:
    0.30 mm (0.0118 in.)

    If the thrust clearance is more than the maximum, replace the idle gear thrust plate. If necessary, replace the No. 1 idle gear and/or No. 1 idle gear shaft.


19. REMOVE IDLE GEAR THRUST PLATE

  1. A102775
    Remove the 2 bolts and idle gear thrust plate.


20. REMOVE NO. 1 IDLE GEAR

  1. A051316E01
    Remove the No. 1 idle gear together with the No. 1 and No. 2 idle sub gears.

  1. A069830E01
    Mount the No. 1 idle gear and No. 2 idle sub gear in a vise.

    NOTICE:
    Be careful not to damage the gears.

  1. A069831E02
    Using SST, turn the No. 1 idle sub gear clockwise and remove the service bolt.
    SST
    09960-10010   (09962-01000, 09963-00600)
    Text in Illustration 
    *1
    Service Bolt

  1. A069832E01
    Using snap ring pliers, remove the shaft snap ring.

  1. A069833E03
    Remove the wave washer, No. 1 idle sub gear and idle gear spring.
    Text in Illustration 
    *1
    Wave Washer
    *2
    No. 1 Idle Sub Gear
    *3
    Idle Gear Spring

  1. A051322E01
    Remove the No. 1 idle gear and set it in a vise.

    NOTICE:
    Be careful not to damage the gear.

  1. A069834E01
    Using snap ring pliers, remove the shaft snap ring.

  1. A069835E05
    Remove the wave washer, No. 2 idle sub gear and idle gear spring.
    Text in Illustration 
    *1
    Wave Washer
    *2
    No. 2 Idle Sub Gear
    *3
    Idle Gear Spring


21. REMOVE NO. 1 IDLE GEAR SHAFT

  1. A051317E01
    Remove the No. 1 idle gear shaft.


22. INSPECT BACKLASH OF CRANKSHAFT TIMING GEAR TO NO. 1 IDLE GEAR
  1. Install the No. 1 idle gear.

  1. A060170E01
    Using a dial indicator, measure the backlash.

    Standard gear backlash:
    0.02 to 0.15 mm (0.0008 to 0.0060 in.)

    Maximum gear backlash:
    0.20 mm (0.0079 in.)

    If the gear backlash is more than the maximum, replace the gears as a set.

  1. Remove the No. 1 idle gear.


23. REMOVE CRANKSHAFT TIMING GEAR

  1. A060156E01
    Using SST, remove the crankshaft timing gear.
    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05010, 09954-05021)


24. INSPECT BACKLASH OF OIL PUMP GEAR TO NO. 1 BALANCESHAFT

  1. G036494E01
    Using a dial indicator, measure the backlash.

    Standard gear backlash:
    0.02 to 0.15 mm (0.0008 to 0.0060 in.)

    Maximum gear backlash:
    0.20 mm (0.0079 in.)

    If the gear backlash is more than the maximum, replace the gears as a set.


25. INSPECT BACKLASH OF INJECTION GEAR TO NO. 2 BALANCESHAFT
  1. Install the fuel supply pump with the 2 nuts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. A060158E01
    Using SST, install the injection gear with the nut.

    Torque:
    64 N*m{ 650 kgf*cm , 47 ft.*lbf }

    SST
    09960-10010   (09962-01000, 09963-01000)

  1. G036495E01
    Using a dial indicator, measure the backlash.

    Standard gear backlash:
    0.02 to 0.15 mm (0.0008 to 0.0060 in.)

    Maximum gear backlash:
    0.20 mm (0.0079 in.)

    If the gear backlash is more than the maximum, replace the gears as a set.


26. INSPECT BACKLASH OF INJECTION GEAR TO NO. 1 IDLE GEAR
  1. Install the No. 1 idle gear without the sub gears.

  1. A060172E01
    Using a dial indicator, measure the backlash.

    Standard gear backlash:
    0.02 to 0.15 mm (0.0008 to 0.0060 in.)

    Maximum gear backlash:
    0.20 mm (0.0079 in.)

    If the gear backlash is more than the maximum, replace the gears as a set.

  1. A060158E01
    Using SST, remove the nut and injection gear.
    SST
    09960-10010   (09962-01000, 09963-01000)

  1. Remove the 2 nuts and fuel supply pump.

  1. Remove the No. 1 idle gear.


27. REMOVE OIL CHECK VALVE SUB-ASSEMBLY (w/ DPF)

  1. A239305
    Using a 6 mm hexagon wrench, remove the bolt and oil check valve from the timing gear cover.


28. INSPECT OIL CHECK VALVE SUB-ASSEMBLY (w/ DPF)

  1. A231899E01
    Push the ball of the oil check valve to check if it is stuck.
    Text in Illustration 
    *1
    Ball
    If the oil check valve is stuck, replace the oil check valve sub-assembly.


29. REMOVE ENGINE OIL LEVEL SENSOR
  1. Remove the 4 bolts and engine oil level sensor.


30. REMOVE OIL PAN SUB-ASSEMBLY

  1. A239346
    Disconnect the vinyl tube from the oil pan.

  1. A074128E02
    Remove the 22 bolts and 2 nuts.

  1. A057637E04
    w/ DPF:
    Insert the blade of an oil pan seal cutter between the oil pan and cylinder block, cut through the applied sealer, and then remove the oil pan.

    NOTICE:
    1. Do not use the oil pan seal cutter for the area between the oil pan and timing gear case, or for the area between the oil pan and rear oil seal retainer.
    2. Be careful not to damage the oil pan flange.

  1. A057637E04
    w/o DPF:
    Insert the blade of an oil pan seal cutter between the oil pan and cylinder block stiffening plate, cut through the applied sealer, and then remove the oil pan and cylinder block stiffening plate.

    NOTICE:
    1. Do not use the oil pan seal cutter for the area between the oil pan and timing gear case, or for the area between the oil pan and rear oil seal retainer.
    2. Be careful not to damage the oil pan flange.


31. REMOVE OIL STRAINER SUB-ASSEMBLY

  1. A102736
    Remove the 2 bolts, 2 nuts, oil strainer and gasket.


32. REMOVE TIMING GEAR CASE ASSEMBLY

  1. A069842E01
    Remove the union bolt and 8 bolts.

  1. A102853E02
    Pry the timing gear case at the location shown in the illustration and remove the timing gear case.

  1. A051330E01
    Remove the gasket.

  1. A069840E03
    Remove the 2 O-rings.


33. INSPECT NO. 1 BALANCESHAFT THRUST CLEARANCE

  1. A051346E01
    Using a dial indicator, measure the thrust clearance by moving the No. 1 balanceshaft back and forth.

    Standard thrust clearance:
    0.065 to 0.140 mm (0.0026 to 0.0055 in.)

    Maximum thrust clearance:
    0.25 mm (0.0098 in.)

    If the thrust clearance is more than the maximum, replace the balanceshaft thrust washer. If the thrust clearance is still more than the maximum clearance, replace the No. 1 balanceshaft sub-assembly.


34. REMOVE NO. 1 BALANCESHAFT SUB-ASSEMBLY

  1. A051332E01
    Remove the 2 bolts and No. 1 balanceshaft.


35. REMOVE NO. 1 BALANCESHAFT DRIVEN GEAR

  1. A051333E01
    Mount the No. 1 balanceshaft between aluminum plates in a vise.

    NOTICE:
    Be careful not to damage the No. 1 balanceshaft.

  1. Remove the bolt, No. 1 balanceshaft driven gear and balanceshaft thrust washer.


36. INSPECT NO. 2 BALANCESHAFT THRUST CLEARANCE

  1. A051347E01
    Using a dial indicator, measure the thrust clearance by moving the No. 2 balanceshaft back and forth.

    Standard thrust clearance:
    0.065 to 0.140 mm (0.0026 to 0.0055 in.)

    Maximum thrust clearance:
    0.25 mm (0.0098 in.)

    If the thrust clearance is more than the maximum, replace the balanceshaft thrust washer. If the thrust clearance is still more than the maximum clearance, replace the No. 2 balanceshaft sub-assembly.


37. REMOVE NO. 2 BALANCESHAFT SUB-ASSEMBLY

  1. A051334E01
    Remove the 2 bolts and No. 2 balanceshaft.


38. REMOVE NO. 2 BALANCESHAFT DRIVEN GEAR

  1. A051335E01
    Mount the No. 2 balanceshaft between aluminum plates in a vise.

    NOTICE:
    Be careful not to damage the No. 2 balanceshaft.

  1. Remove the bolt, No. 2 balanceshaft driven gear and balanceshaft thrust washer.


39. REMOVE REAR ENGINE OIL SEAL RETAINER

  1. A052295E01
    Remove the 5 bolts.

  1. Using a screwdriver, remove the rear engine oil seal retainer by prying between the rear engine oil seal retainer and cylinder block.


40. REMOVE CYLINDER BLOCK OIL ORIFICE

41. INSPECT CONNECTING ROD THRUST CLEARANCE

  1. A060198E01
    Using a dial indicator, measure the thrust clearance while moving the connecting rod back and forth.

    Standard thrust clearance:
    0.100 to 0.300 mm (0.0039 to 0.0118 in.)

    Maximum thrust clearance:
    0.40 mm (0.0157 in.)

    If the thrust clearance is more than the maximum, replace the connecting rod sub-assembly. If necessary, replace the crankshaft.


42. REMOVE PISTON AND CONNECTING ROD

  1. A060199E07
    Remove the 2 connecting rod cap bolts.
    Text in Illustration 
    *1
    Matchmark

    HINT:
    Check the matchmarks on the connecting rod and cap to ensure correct reassembly.

  1. A060236E01
    Using the 2 removed connecting rod bolts, pry the connecting rod cap back and forth and remove the connecting rod cap.

    HINT:
    Keep the lower bearing and connecting rod cap together.

  1. Clean the crank pin and bearing.

  1. Check the crank pin and bearings for pitting and scratches.
    If the crank pin or a bearings is damaged, replace the bearings. If necessary, grind or replace the crankshaft.

  1. A060191E02
    Using a ridge reamer, remove all carbon from the top of the cylinder.

  1. Push the piston, connecting rod and upper bearing through the top of the cylinder block to remove them.

    HINT:
    1. Keep the bearings, connecting rod and cap together.
    2. Be sure to organize the removed piston and connecting rod assemblies in such a way that they can be reinstalled exactly as before.


43. INSPECT CONNECTING ROD OIL CLEARANCE

  1. A060239E03
    Lay a strip of Plastigage across the crank pin.
    Text in Illustration 
    *1
    Plastigage

  1. A060199E07
    Install the connecting rod cap with the 2 bolts.
    Text in Illustration 
    *1
    Matchmark

    NOTICE:
    Do not turn the crankshaft.

    HINT:
    1. The connecting rod cap bolts are tightened in 2 progressive steps.
    2. If any connecting rod bolt is broken or deformed, replace it.


    1. Apply a light coat of engine oil to the threads and under the heads of the connecting rod cap bolts.

    2. Install and alternately tighten the bolts of the connecting rod cap in several passes.

      Torque:
      35 N*m{ 357 kgf*cm , 26 ft.*lbf }

      If any one of the connecting rod cap bolts does not meet the torque specification, replace the cap bolt.

    3. A060197E05
      Mark the front of each of the connecting rod cap bolts with paint.
      Text in Illustration 
      *1
      Paint Mark
      *a
      Front

    4. Tighten the connecting rod cap bolts by 90° as shown in the illustration.

    5. Check that the paint marks are now at a 90° angle to the front.

  1. Check the matchmarks on the connecting rod and cap to ensure correct reassembly.

  1. Remove the 2 bolts, connecting rod cap and lower bearing.

  1. A060240E03
    A061381E03
    Measure the Plastigage at its widest point.

    Standard oil clearance:
    0.036 to 0.054 mm (0.0014 to 0.0021 in.)

    Maximum oil clearance:
    0.10 mm (0.0039 in.)

    Text in Illustration 
    *1
    Plastigage
    If the oil clearance is more than the maximum, replace the bearings. If necessary, grind or replace the crankshaft.

    HINT:
    If using a standard bearing, replace it with one that has the same number. If the number of the bearing cannot be determined, select the correct bearing by adding together the numbers imprinted on the crankshaft and connecting rod, and then selecting the bearing with the same number as the total. There are 5 sizes of standard bearings, marked 2, 3, 4, 5 and 6.

    Bearing Size 
    Item
    Number Mark
    Connecting rod cap
    1
    2
    3
    Crankshaft
    1
    2
    3
    1
    2
    3
    1
    2
    3
    Bearing to be used
    2
    3
    4
    3
    4
    5
    4
    5
    6
    EXAMPLE:
    Connecting rod cap "2" + Crankshaft "3" =
    Total number 5 (Use bearing "5")
    Text in Illustration 
    *1
    Mark 1, 2 or 3
    *2
    Mark 2, 3, 4, 5 or 6
    *3
    No. 1
    *4
    No. 2
    *5
    No. 3
    *6
    No. 4

    Reference:
    Standard Connecting Rod Big End Inside Diameter:
    Item
    Specified Condition
    Mark 1
    62.014 to 62.020 mm (2.4415 to 2.4417 in.)
    Mark 2
    62.020 to 62.026 mm (2.4417 to 2.4420 in.)
    Mark 3
    62.026 to 62.032 mm (2.4420 to 2.4422 in.)
    Standard Crank Pin Diameter:
    Item
    Specified Condition
    Mark 1
    58.994 to 59.000 mm (2.3226 to 2.3228 in.)
    Mark 2
    58.988 to 58.994 mm (2.3224 to 2.3226 in.)
    Mark 3
    58.982 to 58.988 mm (2.3221 to 2.3224 in.)
    Standard Sized Connecting Rod Bearing Center Wall Thickness:
    Item
    Specified Condition
    Mark 2
    1.486 to 1.489 mm (0.0585 to 0.0586 in.)
    Mark 3
    1.489 to 1.492 mm (0.0586 to 0.0587 in.)
    Mark 4
    1.492 to 1.495 mm (0.0587 to 0.0589 in.)
    Mark 5
    1.495 to 1.498 mm (0.0589 to 0.0590 in.)
    Mark 6
    1.498 to 1.501 mm (0.0590 to 0.0591 in.)

  1. Completely remove the Plastigage.


44. INSPECT CRANKSHAFT THRUST CLEARANCE

  1. A060269E01
    Using a dial indicator, measure the thrust clearance while prying the crankshaft back and forth with a screwdriver.

    Standard thrust clearance:
    0.040 to 0.240 mm (0.0016 to 0.0094 in.)

    Maximum thrust clearance:
    0.30 mm (0.0118 in.)

    If the thrust clearance is more than the maximum, replace the thrust washers as a set.

    Standard Thrust Washer Thickness:
    Item
    Specified Condition
    STD
    2.430 to 2.480 mm (0.0957 to 0.0976 in.)
    O/S 0.125
    2.555 to 2.605 mm (0.1006 to 0.1026 in.)
    O/S 0.25
    2.493 to 2.543 mm (0.0982 to 0.1001 in.)


45. INSPECT CRANKSHAFT OIL CLEARANCE

  1. A060270E09
    Uniformly loosen and remove the 10 crankshaft bearing cap bolts in several passes in the sequence shown in the illustration.

  1. A060227E01
    Using the removed crankshaft bearing cap bolts, pry the cap back and forth and remove the crankshaft bearing caps, lower crankshaft bearings and lower thrust washers (No. 5 crankshaft bearing cap only).

    HINT:
    1. Keep the lower bearing and crankshaft bearing cap together.
    2. Be sure to organize the bearing caps and lower thrust washers (No. 5 crankshaft bearing only) in such a way that they can be reinstalled exactly as before.

  1. Lift out the crankshaft.

  1. Clean each main journal and bearing.

  1. Check each crankshaft journal and bearing for pitting and scratches.
    If a journal or bearing is damaged, replace the bearings. If necessary, grind or replace the crankshaft.

  1. Place the crankshaft on the cylinder block.

  1. A060224E02
    Lay a strip of Plastigage across each journal.
    Text in Illustration 
    *1
    Plastigage

  1. A060226E01
    Place the 5 crankshaft bearing caps in their proper locations.

  1. A060270E02
    Install the 5 crankshaft bearing caps with the 10 bolts.

    NOTICE:
    Do not turn the crankshaft.

    HINT:
    1. The crankshaft bearing cap bolts are tightened in 2 progressive steps.
    2. If a crankshaft bearing cap bolt is broken or deformed, replace it.


    1. Apply a light coat of engine oil to the threads and under the bolt heads of the crankshaft bearing cap bolts.

    2. Install and uniformly tighten the 10 bolts of the crankshaft bearing caps in several passes in the sequence shown in the illustration.

      Torque:
      50 N*m{ 510 kgf*cm , 37 ft.*lbf }

      If any one of the bearing cap bolts does not meet the torque specification, replace the bearing cap bolt.

    3. A060271E08
      Mark the front of each crankshaft bearing cap bolt with paint.
      Text in Illustration 
      *1
      Paint Mark
      *a
      Front

    4. Tighten the crankshaft bearing cap bolts by 90° in the numerical order shown in the previous illustration.

    5. Check that the paint marks are now at a 90° angle to the front.

  1. Remove the 10 bolts and 5 crankshaft bearing caps.

  1. A060225E02
    A076751E03
    Measure the Plastigage at its widest point.

    Standard Oil Clearance:
    Item
    Specified Condition
    STD
    0.030 to 0.048 mm (0.0012 to 0.0019 in.)
    U/S 0.25, U/S 0.50
    0.037 to 0.077 mm (0.0015 to 0.0030 in.)

    Maximum clearance:
    0.10 mm (0.0039 in.)

    Text in Illustration 
    *1
    Plastigage
    If the oil clearance is more than the maximum, replace the bearings. If necessary, grind or replace the crankshaft.

    HINT:
    If replacing the cylinder block sub-assembly, the bearing oil clearance will be within the standard range.

    Standard oil clearance:
    0.030 to 0.048 mm (0.0012 to 0.0019 in.)

    HINT:
    If using a standard bearing, replace it with one that has the same number. If the number of the bearing cannot be determined, select the correct bearing by adding together the numbers imprinted on the cylinder block and crankshaft, and then selecting the bearing with the same number as the total. There are 5 sizes of standard bearings, marked 2, 3, 4, 5 and 6.

    Bearing Size 
    Item
    Number Mark
    Cylinder block
    1
    2
    3
    Crankshaft
    1
    2
    3
    1
    2
    3
    1
    2
    3
    Bearing to be used
    2
    3
    4
    3
    4
    5
    4
    5
    6
    EXAMPLE: Cylinder block "2" + Crankshaft "1"
    = Total number 3 (Use bearing "3")
    Text in Illustration 
    *1
    Mark 2, 3, 4, 5 or 6
    *2
    No. 1
    *3
    No. 2
    *4
    No. 3
    *5
    No. 4
    *6
    No. 5
    *a
    Front

    Reference:
    Standard Cylinder Block Main Journal Bore Diameter:
    Item
    Specified Condition
    Mark 1
    75.000 to 75.006 mm (2.9528 to 2.9530 in.)
    Mark 2
    75.006 to 75.012 mm (2.9530 to 2.9532 in.)
    Mark 3
    75.012 to 75.018 mm (2.9532 to 2.9535 in.)
    Standard Crankshaft Journal Diameter:
    Item
    Specified Condition
    Mark 1
    69.994 to 70.000 mm (2.7557 to 2.7559 in.)
    Mark 2
    69.988 to 69.994 mm (2.7554 to 2.7557 in.)
    Mark 3
    69.982 to 69.988 mm (2.7552 to 2.7554 in.)
    Standard Sized Main Bearing Center Wall Thickness:
    Item
    Specified Condition
    Mark 2
    2.482 to 2.485 mm (0.0977 to 0.0978 in.)
    Mark 3
    2.485 to 2.488 mm (0.0978 to 0.0980 in.)
    Mark 4
    2.488 to 2.491 mm (0.0980 to 0.0981 in.)
    Mark 5
    2.491 to 2.494 mm (0.0981 to 0.0982 in.)
    Mark 6
    2.494 to 2.497 mm (0.0982 to 0.0983 in.)

  1. Completely remove the Plastigage.


46. REMOVE PISTON PIN
  1. Check the fit between the piston and piston pin.

    1. Try to move the piston back and forth on the piston pin.
      If any movement is felt, replace the piston and pin as a set.

  1. A060206E01
    Using a piston ring expander, remove the 2 compression rings.

    HINT:
    Be sure to organize the removed piston rings in such a way that they can be reinstalled exactly as before.

  1. Remove the oil ring by hand.

  1. A060202E01
    Disconnect the connecting rod from the piston.

    1. Using a small screwdriver, pry off the 2 snap rings from the piston.

    2. Gradually heat the piston to approximately 80°C (176°F).

    3. A060212E01
      Using a plastic-faced hammer and brass bar, lightly tap out the piston pin. Then remove the connecting rod.

      HINT:
      1. The piston and pin are a matched set.
      2. Be sure to organize the removed pistons, pins, rings, connecting rods and bearings in such a way that the parts can be reinstalled exactly as before.


47. REMOVE CRANKSHAFT

  1. A060270E09
    Uniformly loosen and remove the 10 crankshaft bearing cap bolts in several passes in the sequence shown in the illustration.

  1. A060227E01
    Using the removed crankshaft bearing cap bolts, pry the cap back and forth, and remove the crankshaft bearing caps, lower crankshaft bearings and lower thrust washers (No. 5 crankshaft bearing cap only).

    HINT:
    1. Keep the lower bearing and crankshaft bearing cap together.
    2. Be sure to organize the bearing caps and lower thrust washers (No. 5 crankshaft bearing only) in such a way that they can be reinstalled exactly as before.

  1. Lift out the crankshaft.

  1. Remove the upper bearings and upper thrust washers from the cylinder block.

    HINT:
    Arrange the main bearing caps, bearings and thrust washers in the correct order.


48. REMOVE NO. 1 OIL NOZZLE SUB-ASSEMBLY
  1. Remove the 4 check valves and 4 No. 1 oil nozzles.


49. REMOVE OIL FILTER BRACKET WITH HEAD STRAIGHT SCREW PLUG

HINT:
It is not necessary to remove the oil filter bracket with head straight screw plug unless it is being replaced.

  1. Remove the oil filter bracket with head straight screw plug and the gasket.


50. REMOVE PLUG

NOTICE:
If coolant leaks from a plug or a plug is corroded, replace the plug.

  1. Remove the plug from the cylinder block.


51. REMOVE PLATE PLUG

HINT:
It is not necessary to remove the plate plug unless it is being replaced.

  1. Remove the bolt, plate plug and O-ring.


52. REMOVE HOLE PLUG

HINT:
It is not necessary to remove the hole plug unless it is being replaced.

  1. Remove the bolt, hole plug and O-ring.


53. REMOVE RING PIN

HINT:
It is not necessary to remove a ring pin unless it is being replaced.

  1. A142382E02
    Remove the 2 ring pins shown in the illustration.
    Text in Illustration 
    *a
    Cylinder Head Side


54. REMOVE STRAIGHT PIN

HINT:
It is not necessary to remove a straight pin unless it is being replaced.

  1. A142381E02
    Remove the 6 straight pins shown in the illustration.
    Text in Illustration 
    *a
    Front Side
    *b
    Rear Side


55. REMOVE STUD BOLT

HINT:
If a stud bolt is deformed or its threads are damaged, replace it.

  1. Remove the 11 stud bolts shown in the illustration.

    A242585E02

    Text in Illustration 
    *a
    Front Side
    *b
    Upper Side
    *c
    Left Side
    *d
    Lower Side


56. REMOVE TIGHT PLUG

HINT:
If coolant leaks from a tight plug or a plug is corroded, replace it.

  1. Remove the 13 tight plugs shown in the illustration.

    A242586E02

    Text in Illustration 
    *a
    Right Side
    *b
    Front Side
    *c
    Left Side
    *d
    Rear Side

← COMPONENTS (from Oct 2014)INSPECTION (from Oct 2014) →