2014-2019 Hiace · Service Manual TRANSMISSION

DISASSEMBLY

Removal / installation · Vehicles built from Dec 2015

Versions by build date: Oct 2014 – Nov 2015 from Dec 2015


1. REMOVE MANUAL TRANSMISSION FILLER PLUG

  1. C086347
    Remove the filler plug and gasket from the manual transmission case.


2. REMOVE DRAIN (MTM) PLUG SUB-ASSEMBLY

  1. C344276
    Using a 10 mm hexagon socket wrench, remove the drain plug and gasket from the manual transmission case.


3. REMOVE SPEEDOMETER SENSOR

  1. C112968
    Remove the bolt and speedometer sensor.

  1. Using a screwdriver, remove the O-ring from the speedometer sensor.


4. REMOVE BACK UP LIGHT SWITCH ASSEMBLY

  1. C086355E01
    Using SST, remove the back up light switch assembly and gasket from the manual transmission case.
    SST
    09817-16011  


5. REMOVE CLUTCH HOUSING

  1. D029131
    Remove the 9 bolts.

  1. C086357
    Using a plastic hammer, remove the clutch housing from the transmission case.


6. REMOVE SHIFT LEVER SHAFT HOUSING SUB-ASSEMBLY

  1. C112972E01
    Remove the 6 bolts, shift lever shaft housing and clamp from the manual transmission case.

  1. Remove the shift lever shaft housing gasket from the manual transmission case.


7. REMOVE EXTENSION HOUSING DUST(MTM) DEFLECTOR

  1. C086359
    Using a brass bar and a hammer, remove the extension housing dust deflector from the extension housing.


8. REMOVE EXTENSION (MTM) HOUSING SUB-ASSEMBLY

  1. C112973
    Remove 8 bolts.

  1. C086361
    Using a plastic hammer, remove the extension housing from the manual transmission case.


9. REMOVE TRANSMISSION MAGNET

  1. D029141
    Remove the transmission magnet from the extension housing.


10. REMOVE EXTENSION HOUSING OIL RECEIVER PIPE

  1. C086363
    Remove the bolt and extension housing oil receiver pipe from the extension housing.


11. REMOVE EXTENSION HOUSING OIL RECEIVER PIPE NO.1

  1. D029142
    Remove the extension housing oil receiver pipe No.1 from the extension housing.


12. REMOVE MANUAL TRANSMISSION EXTENSION HOUSING OIL SEAL

  1. C086365E01
    Using SST, remove the manual transmission extension housing oil seal from the extension housing.
    SST
    09308-00010  


13. REMOVE BEARING RETAINER FRONT(MTM)

  1. D029148
    Remove the 8 bolts.

  1. w/o Gasket:

    1. Remove the bearing retainer from the transmission case.

  1. w/ Gasket:

    1. Remove the bearing retainer front and transmission front bearing retainer gasket from the manual transmission case.


14. REMOVE TRANSMISSION FRONT BEARING RETAINER OIL SEAL

  1. D033559
    Using a screwdriver, remove the transmission front bearing retainer oil seal from the bearing retainer front.


15. REMOVE FRONT BEARING SHAFT SNAP RING

  1. C086368
    Using a snap ring expander, remove the front bearing shaft snap ring from the manual transmission case.


16. REMOVE COUNTER GEAR FRONT BEARING SNAP RING NO.1

  1. C086369
    Using a snap ring expander, remove the counter gear front bearing snap ring No.1 from the manual transmission case.


17. REMOVE MANUAL TRANSMISSION CASE

  1. C086370
    Stand the manual transmission assembly as shown in the illustration.

  1. Using a plastic hammer, carefully tap off the manual transmission case.

  1. Remove the manual transmission case from the intermediate plate as shown in the illustration.


18. FIX INTERMEDIATE PLATE

  1. C086371
    Fix the intermediate plate in a vise.


19. REMOVE SHIFT DETENT BALL

  1. C086372
    Using a "torx" socket wrench T40, remove the 3 shift detent ball spring seats No.1 from the intermediate plate.

  1. C086373
    Using a magnetic finger, remove the 3 compression springs and 3 shift detent balls from the intermediate plate.


20. REMOVE SHIFT DETENT BALL NO.2

  1. C086374
    Using a "torx" socket wrench T40, remove the shift detent ball spring seat No.2 from the intermediate plate.

  1. C086375
    Using a magnetic finger, remove the compression spring and shift detent ball No.2 from the intermediate plate.


21. REMOVE GEAR SHIFT FORK SHAFT NO.4

  1. C086376
    Remove the shift fork bolt from the gear shift fork No.3.

  1. C114088
    Using a pin punch (5 mm) and a hammer, remove the slotted spring pin from the reverse shift head.

  1. C114089
    Using 2 screwdrivers and a hammer, remove the shaft snap ring from the gear shift fork shaft No.4

    NOTICE:
    Use a shop rag to prevent the snap ring from flying off.

  1. C114090
    Remove the ball from the intermediate plate.

  1. C114091
    Remove the gear shift fork shaft No.4 and reverse shift fork ball.


22. REMOVE REVERSE SHIFT HEAD

  1. C114281
    Remove the reverse shift head from the reverse shift fork shaft.


23. REMOVE GEAR SHIFT HEAD NO.3

  1. C114094
    Using a pin punch (5 mm) and a hammer, remove the slotted spring pin from the gear shift head No.3.

  1. Remove the gear shift head from the reverse shift fork shaft.


24. REMOVE SHIFT INTER LOCK PIN NO.2

  1. C114093
    Using a magnetic finger, remove shift inter lock pin No.2 from the reverse shift fork shaft.


25. REMOVE REVERSE SHIFT FORK SHAFT

  1. C114095
    Remove the reverse shift fork shaft, ball and compression spring.

    NOTICE:
    Cover the hole with a shop rag to prevent the ball from popping out.


26. REMOVE SHIFT INTER LOCK PIN NO.1

  1. C086389
    Using a magnetic finger, remove the shift inter lock pin No.1 from the intermediate plate.


27. REMOVE SHIFT INTER LOCK PIN NO.2

  1. C086390
    Using a magnetic finger, remove shift inter lock pin No.2 from the gear shift fork shaft No.2.


28. REMOVE GEAR SHIFT FORK SHAFT NO.2

  1. C086391
    Using a pin punch and a hammer, remove the slotted spring pin from the gear shift fork No.2.

  1. C086392
    Remove the shift fork shaft snap ring from the gear shift fork shaft No.2.

  1. C086393
    Remove the gear shift fork shaft No.2 from the intermediate plate.


29. REMOVE SHIFT INTER LOCK PIN NO.1

  1. C086394
    Using a magnetic finger, remove shift inter lock pin No.1 from the intermediate plate.


30. REMOVE GEAR SHIFT FORK SHAFT NO.1

  1. C086395
    Remove the shift fork bolt from the gear shift fork No.1.

  1. C086396
    Remove the gear shift fork shaft No.1 assembly and gear shift fork No.1 from the intermediate plate.

  1. C086397
    Using a pin punch (5 mm) and a hammer, remove the slotted spring pin from the gear shift head No.1.

  1. Remove the gear shift head No.1 from the gear shift fork shaft No.1.


31. REMOVE GEAR SHIFT FORK NO.2

  1. C086398
    Remove the gear shift fork No.2 from the transmission hub sleeve No.2.


32. INSPECT COUNTER SHAFT 5TH GEAR THRUST CLEARANCE

  1. C086399
    Using a feeler gauge, measure the counter shaft 5th gear thrust clearance.

    Standard clearance:
    0.125 to 0.325 mm (0.0049 to 0.0128 in.)

    Maximum clearance:
    0.325 mm (0.0128 in.)


33. REMOVE COUNTER SHAFT 5TH GEAR

  1. D033537
    Using 2 screwdrivers and a hammer, tap out the counter gear rear shaft snap ring from the counter gear.

  1. D033538E01
    Using SST, remove the gear spline piece No.5 and synchronizer ring No.3 from the counter gear.
    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05010, 09954-05021)

  1. D033539
    Remove the counter shaft 5th gear assembly and counter 5th gear bearing from the counter gear.


34. REMOVE 5TH GEAR THRUST WASHER

  1. D033540
    Remove the 5th gear thrust washer from the counter gear.

  1. D033541
    Using a magnetic finger, remove the 5th gear bearing inner race lock ball from the counter gear.


35. REMOVE REVERSE SHIFT ARM BRACKET

  1. D033529
    Remove the 2 bolts and reverse shift arm bracket with the shift arm from the intermediate plate.


36. REMOVE REVERSE SHIFT ARM

  1. D033309
    Using a screwdriver, remove the E-ring.

  1. Remove the shift fork from the shift arm.


37. REMOVE REVERSE IDLER GEAR SUB-ASSEMBLY

  1. D033542
    Remove the bolt and reverse idler gear shaft stopper from the intermediate plate.

  1. D033543
    Remove the the reverse idler gear shaft and reverse idler gear sub-assembly from the intermediate plate.


38. INSPECT REVERSE IDLER GEAR RADIAL CLEARANCE

  1. C086408
    Using a dial indicator, inspect the reverse idler gear radial clearance.

    Standard clearance:
    0.04 to 0.08 mm (0.0016 to 0.0031 in.)

    Maximum clearance:
    0.13 mm (0.0051 in.)

    If the clearance exceeds the maximum, replace the reverse idler gear.


39. INSPECT REVERSE IDLER GEAR SUB-ASSEMBLY

  1. D033607E01
    Using a feeler gauge, measure the clearance between the reverse idler gear and reverse shift arm.

    Standard clearance:
    0.05 to 0.35 mm (0.0020 to 0.0138 in.)

    Maximum clearance:
    0.35 mm (0.0138 in.)

    If the clearance exceeds the maximum, replace the reverse idler gear and reverse shift arm.


40. REMOVE OUTPUT SHAFT REAR BEARING(MTM) RETAINER

  1. D033544
    Using a "torx" socket wrench T40, remove the 4 screws and output shaft rear bearing retainer from the intermediate plate.


41. REMOVE COUNTER GEAR

  1. D029185
    Using a snap ring expander, remove the snap ring from the counter shaft center bearing.

  1. D033545E01
    Using SST, remove the counter shaft center bearing and the counter gear assembly from the intermediate plate.
    SST
    09950-40011   (09951-04010, 09952-04010, 09953-04010, 09954-04010, 09955-04011, 09958-04011)


42. REMOVE INPUT SHAFT ASSEMBLY

  1. C086413
    Remove the input shaft assembly with the 13 input shaft bearings and synchronizer ring No.1 from the output shaft.


43. REMOVE OUTPUT SHAFT ASSEMBLY

  1. D033546
    Using a snap ring expander, remove the output shaft bearing snap ring from the output shaft assembly.

  1. D033547
    Remove the output shaft assembly from the intermediate plate by pulling on the output shaft assembly and tapping on the intermediate plate with a plastic hammer.

← DISASSEMBLY (Oct 2014 – Nov 2015)INSPECTION (from Oct 2014) →