2014-2019 Hiace · Service Manual TRANSMISSION

REASSEMBLY

Removal / installation · Vehicles built from Oct 2014


1. INSTALL TRANSMISSION CLUTCH HUB NO.2

  1. C086574E01
    Coat the hub sleeve with gear oil, and install it to the clutch hub.

    NOTICE:
    Be sure to set the hub sleeve to the clutch hub in the correct direction.

  1. C086575
    Install the 3 synchromesh shifting keys to the clutch hub with the 2 synchromesh shifting key springs.

    HINT:
    Do not set the openings of the shifting key springs in the same position.


2. INSTALL 3RD GEAR NEEDLE ROLLER BEARING

  1. C086556
    Coat the needle roller bearing with gear oil, and install it to the output shaft.


3. INSTALL 3RD GEAR

  1. C086577
    Coat the 3rd gear with gear oil, and install it to the output shaft.


4. INSTALL SYNCHRONIZER RING NO.2

  1. C086576
    Coat the synchronizer ring with gear oil, and install it to the 3rd gear.


5. INSTALL TRANSMISSION CLUTCH HUB NO.2

  1. C086578
    Using SST and a press, press in the clutch hub No.2 to the output shaft.
    SST
    09316-60011   (09316-00021)

  1. C086579
    Select a clutch hub shaft snap ring that will allow the minimum amount of axial play.

    Standard clearance:
    0.1 mm (0.039 in.) or less

    Clutch hub shaft snap ring thickness: 
    Mark
    Thickness: mm (in.)
    C-1
    1.75 to 1.80 (0.0689 to 0.0709)
    D
    1.80 to 1.85 (0.0709 to 0.0728)
    D-1
    1.85 to 1.90 (0.0728 to 0.0748)
    E
    1.90 to 1.95 (0.0748 to 0.0768)
    E-1
    1.95 to 2.00 (0.0768 to 0.0787)
    F
    2.00 to 2.05 (0.0787 to 0.0807)
    F-1
    2.05 to 2.10 (0.0807 to 0.0827)

  1. C086553
    Using a snap ring expander, install the snap ring.


6. INSPECT 3RD GEAR THRUST CLEARANCE

  1. C086580
    Using a feeler gauge, measure the thrust clearance.

    Standard clearance:
    0.10 to 0.25 mm (0.0039 to 0.0098 in.)


7. INSTALL TRANSMISSION CLUTCH HUB NO.1

  1. C086581E01
    Coat the reverse gear with gear oil, and install it to the clutch hub.

    NOTICE:
    Be sure to set the reverse gear to the clutch hub in the correct direction.

  1. C086575
    Install 3 synchromesh shifting keys to the clutch hub with the 2 synchromesh shifting key springs.

    HINT:
    Do not set the openings of the shifting key springs in the same position.


8. INSTALL 2ND GEAR NEEDLE ROLLER BEARING

  1. C086582
    Coat the needle roller bearing with gear oil, and install it to the output shaft.


9. INSTALL 2ND GEAR

  1. C086583
    Coat the 2nd gear with gear oil, and install it to the output shaft.


10. INSTALL SYNCHRONIZER RING NO.1 (for 2nd Gear)

  1. C086584
    Coat the synchronizer ring No.1 with gear oil, and install it to the 2nd gear.


11. INSTALL TRANSMISSION CLUTCH HUB NO.1

  1. C086585E01
    Using SST and a press, press in the clutch hub to the output shaft.
    SST
    09316-60011   (09316-00021)


12. INSPECT 2ND GEAR THRUST CLEARANCE

  1. Z003552E02
    Using a dial indicator, measure the thrust clearance.

    Standard clearance:
    0.10 to 0.25 mm (0.0039 to 0.0098 in.)


13. INSTALL SYNCHRONIZER RING NO.1 (for 1st Gear)

  1. C086587
    Coat the synchronizer ring with gear oil, and install it to the clutch hub No.1.


14. INSTALL 1ST GEAR BEARING INNER RACE LOCK KEY OR BALL

  1. C086588
    Coat the lock ball with gear oil, and install it to the output shaft.


15. INSTALL 1ST GEAR BEARING INNER RACE

  1. C086589
    Coat the needle roller bearing with gear oil.

  1. Install the inner lace and the needle roller bearing to the 1st gear.


16. INSTALL 1ST GEAR

  1. C086590
    Coat the 1st gear with gear oil, and install it to the output shaft.


17. INSTALL OUTPUT SHAFT CENTER BEARING

  1. C086591E01
    Using SST and a press, press in the center bearing to the output shaft.
    SST
    09316-60011   (09316-00021)


18. INSPECT 1ST GEAR THRUST CLEARANCE

  1. C274865
    Using a dial indicator, measure the thrust clearance.

    Standard clearance:
    0.10 to 0.25 mm (0.0039 to 0.0098 in.)


19. INSTALL 5TH GEAR

  1. C086593E01
    Using SST and a press, press in the 5th gear to the output shaft.
    SST
    09316-60011   (09316-00021)

  1. D033312
    Select a snap ring that will allow minimal axial play.

    Standard clearance:
    0.1 mm (0.039 in.) or less

    Output shaft bearing shaft snap ring 
    Mark
    Thickness: mm (in.)
    A
    2.67 to 2.72 (0.1051 to 0.1071)
    B
    2.73 to 2.78 (0.1075 to 0.1094)
    C
    2.79 to 2.84 (0.1098 to 0.1118)
    D
    2.85 to 2.90 (0.1122 to 0.1141)
    E
    2.91 to 2.96 (0.1146 to 0.1165)
    F
    2.97 to 3.02 (0.1169 to 0.1189)
    G
    3.03 to 3.08 (0.1193 to 0.1213)
    H
    3.09 to 3.14 (0.1217 to 0.1236)
    J
    3.15 to 3.20 (0.1240 to 0.1260)
    K
    3.21 to 3.26 (0.1264 to 0.1283)
    L
    3.27 to 3.32 (0.1287 to 0.1307)

  1. D033313
    Using a screwdriver and hammer, tap in the snap ring.


20. INSTALL SPEEDOMETER DRIVE (MTM) GEAR

  1. G034243
    Using a snap ring expander, install the snap ring.

  1. Install the ball.

  1. Install the drive gear.

  1. Using a snap ring expander, install the snap ring.


21. INSPECT 3RD GEAR RADIAL CLEARANCE

  1. C086543
    Using a dial indicator, measure the radial clearance.

    Standard clearance:
    0.008 to 0.0034 mm (0.0003 to 0.00134 in.)

    If the clearance is not as specified, replace the 3rd gear needle roller bearing.


22. INSPECT 2ND GEAR RADIAL CLEARANCE

  1. C086542
    Using a dial indicator, measure the radial clearance.

    Standard clearance:
    0.008 to 0.0034 mm (0.0003 to 0.00134 in.)

    If the clearance is not as specified, replace the 2nd gear needle roller bearing.


23. INSPECT 1ST GEAR RADIAL CLEARANCE

  1. C086541
    Using a dial indicator, measure the radial clearance.

    Standard clearance:
    0.009 to 0.056 mm (0.0004 to 0.0022 in.)

    If the clearance is not as specified, replace the 1st gear needle roller bearing.

← INSPECTION (from Oct 2014)COMPONENTS (from Oct 2014) →