2014-2019 Hiace · Service Manual TRANSMISSION

DISASSEMBLY

Removal / installation · Vehicles built from Oct 2014


1. REMOVE DRAIN (ATM) PLUG SUB-ASSEMBLY

2. REMOVE BREATHER PLUG HOSE

3. REMOVE TRANSMISSION CONTROL SHAFT LEVER LH
  1. Remove the nut, the washer and the control shaft lever.


4. REMOVE TRANSMISSION CASE PLUG ASSEMBLY

  1. D005553
    Remove the bolt and pull out the plug.

  1. Remove the O-ring from the plug.


5. REMOVE PARK/NEUTRAL POSITION SWITCH ASSEMBLY

  1. C101836E01
    Using a screwdriver, pull up the lock washer.

  1. Remove the nut and lock washer.

  1. C101837
    Remove the bolt and the park/neutral position switch.

    HINT:
    Make sure that the manual valve lever shaft has not been rotated prior to installing the park/neutral position switch as the detent spring may become detached from the manual valve lever shaft.


6. REMOVE OIL COOLER TUBE UNION

  1. C114742
    Remove the 2 oil cooler tube unions.

  1. Remove the O-rings from the oil cooler tube unions.


7. REMOVE TEMPERATURE SENSOR

  1. D005532
    Remove the temperature sensor.

  1. Remove the O-ring from the sensor.


8. REMOVE SPEED SENSOR

  1. Q003894
    Remove the bolt and speed sensor.

  1. Remove the O-ring from the sensor.


9. REMOVE TRANSMISSION REVOLUTION SENSOR

  1. C114743
    Remove the bolt and the transmission revolution sensor.

  1. Remove the O-ring from the sensor.


10. REMOVE EXTENSION HOUSING SUB-ASSEMBLY

  1. C114744
    Remove the 6 bolts.

  1. Remove the extension housing and the gasket.


11. REMOVE EXTENSION HOUSING BUSH APPLY TUBE GASKET

  1. C114745E01
    Remove the bush apply tube gasket.


12. REMOVE EXTENSION HOUSING BUSH APPLY TUBE

  1. C114745E03
    Remove the bush apply tube.


13. REMOVE AUTOMATIC TRANSMISSION EXTENSION HOUSING OIL SEAL

  1. C114746
    Using a screwdriver, remove the extension housing oil seal.


14. REMOVE EXTENSION HOUSING DUST DEFLECTOR

  1. C114747
    Mount the extension housing in a soft jaw vise.

  1. Using a screwdriver and a hammer, remove the extension housing dust deflector.


15. INSPECT EXTENSION HOUSING SUB-ASSEMBLY

  1. C106501
    Using a cylinder gauge, measure the inside diameter of the extension housing bushing.

    Maximum inside diameter:
    40.02 mm (1.5756 in.)

    If the inside diameter is greater than the maximum, replace the extension housing.


16. REMOVE SENSOR ROTOR

  1. C114748E01
    Using a snap ring expander, remove the rear side snap ring.

  1. Remove the sensor rotor and the key.

  1. Using a snap ring expander, remove the front side snap ring.


17. REMOVE AUTOMATIC TRANSMISSION HOUSING

  1. C114749
    Remove the 6 bolts.

  1. Remove the transmission housing.


18. FIX AUTOMATIC TRANSMISSION CASE SUB-ASSEMBLY

  1. AT05873
    Install the transmission case on the overhaul attachment.


19. REMOVE AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY

  1. D009119
    Remove the 19 bolts.

    NOTICE:
    Do not turn the transmission over as this will contaminate the valve body with any foreign matter at the bottom of the pan.

  1. Q007487E04
    Insert oil pan seal cutter between the transmission case and the oil pan. Cut through the seal and remove the oil pan.

    NOTICE:
    Be careful not to damage the oil pan and flange.

  1. Remove the pan by lifting the transmission case.


20. INSPECT AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY

  1. AT01362E03
    Remove any FIPG material and be careful not to drop oil on the contacting surfaces of the transmission case and the oil pan.

  1. Apply FIPG to the oil pan.

    FIPG:
    Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent

  1. Install the oil pan with the 19 bolts.

    Torque:
    7.4 N*m{ 75 kgf*cm , 65 in.*lbf }


21. REMOVE VALVE BODY OIL STRAINER ASSEMBLY

  1. C114750
    Remove the 4 bolts and oil strainer case.


22. REMOVE TRANSMISSION WIRE

  1. C058460
    Disconnect the 4 connectors from each shift solenoid valve.

  1. G022489
    Remove the bolt.

  1. Pull out the solenoid wiring from the transmission case.

  1. Remove the O-rings from the solenoid wiring.


23. REMOVE TRANSMISSION VALVE BODY ASSEMBLY

  1. D029011
    Remove the 20 bolts.


24. REMOVE CHECK BALL BODY

  1. AT04847
    Remove the check ball body and the spring.


25. REMOVE B-2 ACCUMULATOR PISTON

  1. AT05755
    Applying compressed air to the oil hole, remove the B2 accumulator piston and the spring.

  1. Remove the O-rings from the piston.


26. REMOVE C-2 ACCUMULATOR PISTON

  1. AT05755
    Applying compressed air to the oil hole, remove the C2 accumulator piston and the springs.

  1. Remove the O-rings from the piston.


27. REMOVE B-0 ACCUMULATOR PISTON

  1. AT05756
    Applying compressed air to the oil hole, remove the B0 accumulator piston and the spring.

  1. Remove the O-rings from the piston.


28. REMOVE C-0 ACCUMULATOR PISTON

  1. AT05757
    Applying compressed air to the oil hole, remove the C0 accumulator piston and the springs.

  1. Remove the O-ring from the piston.


29. REMOVE PARKING LOCK PAWL BRACKET

  1. AT05103
    Remove the 3 bolts and the parking lock pawl bracket.


30. REMOVE PARKING LOCK ROD SUB-ASSEMBLY

  1. AT05120
    Disconnect the parking lock rod from the manual valve lever.


31. REMOVE PARKING LOCK PAWL SHAFT

  1. Z006720E01
    Pull out the parking lock pawl shaft from the front side, then remove the lock pawl and the spring.

  1. Remove the E-ring from the shaft.


32. REMOVE MANUAL VALVE LEVER SUB-ASSEMBLY

  1. Z006721E01
    Using a hammer and a screwdriver, cut off the spacer and remove it from the shaft.

  1. AT05105
    Using a pin punch and a hammer, drive out the pin.

    HINT:
    Slowly drive out the pin so that it does not fall into the transmission case.

  1. Pull out the manual valve lever shaft through the case, and remove the manual valve lever.


33. REMOVE MANUAL VALVE LEVER SHAFT OIL SEAL

  1. AT05106
    Using screwdriver, remove the 2 manual valve lever shaft oil seals.


34. REMOVE OIL PUMP ASSEMBLY

  1. AT05758
    Stand up the transmission.

  1. Remove the 7 bolts holding the oil pump to the transmission case.

  1. AT07874E01
    Using SST, remove the oil pump.
    SST
    09610-20012  

  1. Remove the O-ring from the oil pump.

  1. AT08431
    Remove the race from the oil pump.


35. REMOVE OVERDRIVE PLANETARY GEAR ASSEMBLY

  1. AT05759
    Remove the O/D planetary gear, O/D direct clutch and one-way clutch from the transmission case.

  1. AT05760
    Remove the bearing and the race.

  1. AT03148
    Remove the race and bearing.


36. REMOVE OVERDRIVE PLANETARY RING GEAR

  1. AT05761
    Remove the O/D planetary ring gear from the transmission case.


37. INSPECT OVERDRIVE BRAKE PISTON

  1. AT08212E01
    Place SST and a dial indicator onto the O/D brake piston.
    SST
    09350-30020   (09350-06120)

  1. AT05762
    Measure the stroke while applying and releasing compressed air (392 to 785 kPa, 4.0 to 8.0 kgf/cm2, 57 to 114 psi).

    Piston stroke:
    1.40 to 1.70 mm (0.0551 to 0.0669 in.)

    If the piston stroke is less than the limit, parts may have been assembled incorrectly, so check and reassemble again.
    If the piston stroke is outside the standard, select another flange.

    HINT:
    There are 7 different thicknesses for the flange.

    Flange thickness: 
    No.
    Thickness
    No.
    Thickness
    77
    3.3 mm (0.130 in.)
    81
    3.8 mm (0.150 in.)
    78
    3.5 mm (0.138 in.)
    82
    3.9 mm (0.154 in.)
    79
    3.6 mm (0.142 in.)
    83
    4.0 mm (0.157 in.)
    80
    3.7 mm (0.146 in.)
    -
    -


38. REMOVE OVERDRIVE BRAKE PACK

  1. AT08427
    Using a screwdriver, remove the snap ring.

  1. AT05781
    Remove the overdrive brake pack.


39. INSPECT PISTON STROKE OF 2ND COAST BRAKE

  1. AT05764E01
    Place a mark on the 2nd coast brake piston rod as shown in the illustration.

  1. AT05765E01
    Using SST, measure the stroke while applying and releasing compressed air (392 to 785 kPa, 4.0 to 8.0 kgf/cm2, 57 to 114 psi).
    SST
    09240-00020  

    Piston stroke:
    1.5 to 3.0 mm (0.059 to 0.018 in.)

    If the stroke is outside the standard, inspect the brake band.


40. REMOVE 2ND COAST BRAKE PISTON

  1. AT05766E01
    Using SST, remove the snap ring.
    SST
    09350-30020   (09350-07060)

  1. AT05767
    Applying compressed air to the oil hole, remove the 2nd coast brake cover, piston and spring.

  1. Remove the 2 O-rings from the cover.


41. REMOVE OVERDRIVE SUPPORT SUB-ASSEMBLY

  1. AT05768
    Remove the bearing.

  1. AT05769
    Remove the 2 bolts holding the O/D support sub-assembly to the case.

  1. AT08426E01
    Using SST, remove the snap ring.
    SST
    09350-30020   (09350-07060)

  1. AT05770E01
    Using SST, remove the O/D support sub-assembly.
    SST
    09350-30020   (09350-07020)

  1. AT08157
    Remove the race.


42. REMOVE DIRECT CLUTCH ASSEMBLY

  1. AT05771
    Remove the direct clutch with the forward clutch from the case.

  1. AT03149
    Remove the 2 bearings and the race.

  1. AT05262E01
    Remove the direct clutch from the forward clutch.

  1. Remove the bearing and thrust washer from the forward clutch.


43. REMOVE 2ND COAST BRAKE BAND ASSEMBLY

  1. AT05111
    Using a screwdriver, remove the E-ring from the pin.

  1. AT05772
    Remove the 2nd coast brake band from the case.

  1. Remove the pin from the brake band.

  1. Remove the E-ring from the pin.


44. REMOVE FRONT PLANETARY RING GEAR SUB-ASSEMBLY

  1. AT05773
    Remove the race.

  1. AT05774
    Remove the front planetary ring gear from the case,

  1. AT08175
    Remove the bearing and race.

  1. AT05775
    Remove the race from the front planetary gear.


45. INSPECT FRONT PLANETARY RING GEAR SUB-ASSEMBLY

  1. AT08187
    Using a dial indicator, measure the inside diameter of the planetary ring gear bushing.

    Maximum inside diameter:
    24.65 mm (0.9705 in.)

    If the inside diameter is greater than the maximum, replace the planetary ring gear.


46. REMOVE FRONT PLANETARY GEAR ASSEMBLY

  1. Z005131E01
    With wooden blocks or equivalent under the output shaft, stand the transmission on the output shaft.

  1. AT05278E01
    Using SST, remove the snap ring.
    SST
    09350-30020   (09350-07070)

  1. AT05778
    Remove the front planetary gear from the case.

  1. AT08186
    Using a screwdriver, remove the bearing and the race from the front planetary gear.


47. INSPECT PLANETARY PINION GEAR THRUST CLEARANCE

  1. AT04456
    Using a feeler gauge, measure the planetary pinion gear thrust clearance.

    Standard clearance:
    0.20 to 0.60 mm (0.0079 to 0.0236 in.)

    Maximum clearance:
    0.65 mm (0.0256 in.)

    If the clearance is greater than the maximum, replace the planetary gear assembly.


48. REMOVE PLANETARY SUN GEAR SUB-ASSEMBLY

  1. AT05779
    Remove the planetary sun gear sub-assembly.

  1. Remove the thrust washer.


49. INSPECT PACK CLEARANCE OF SECOND BRAKE

  1. AT05215
    Using a feeler gauge, measure the clearance between the snap ring and the flange.

    Clearance:
    0.62 to 1.98 mm (0.0244 to 0.0780 in.)

    If the clearance is outside the standard, inspect the discs.


50. REMOVE 2ND BRAKE PACK

  1. AT05780
    Using a screwdriver, remove the snap ring.

  1. C114751
    Remove the flange, the plates and the discs as a set.


51. INSPECT PACK CLEARANCE OF FIRST AND REVERSE BRAKE

  1. AT05212
    Using a feeler gauge, measure the clearance between the plate and the 2nd brake drum.

    Clearance:
    0.70 to 1.22 mm (0.0276 to 0.048 in.)

    If the clearance is outside the standard, inspect the discs.

    HINT:
    There are 8 different thicknesses for the flange.

    Flange thickness: 
    No.
    Thickness
    No.
    Thickness
    67
    5.4 mm (0.213 in.)
    52
    4.6 mm (0.181 in.)
    66
    5.2 mm (0.205 in.)
    53
    4.4 mm (0.173 in.)
    50
    5.0 mm (0.197 in.)
    54
    4.2 mm (0.165 in.)
    51
    4.8 mm (0.189 in.)
    55
    4.0 mm (0.157 in.)


52. REMOVE 2ND BRAKE PISTON SLEEVE

  1. AT05279
    Using a screwdriver, remove the 2nd brake piston sleeve.


53. REMOVE REAR PLANETARY GEAR ASSEMBLY

  1. AT05460E02
    Using SST and a screwdriver, remove the snap ring.
    SST
    09350-30020   (09350-07060)

  1. AT05783
    Remove the rear planetary gear, the 2nd brake drum, the 1st and reverse brake pack and output shaft as an assembly.

  1. AT05784
    Remove the bearing from the case.

  1. AT08183
    Remove the 2nd brake drum.

  1. AT08208
    Remove the cushion plate, the flange, the plates and the discs of the 1st and reverse brake.

  1. AT05107
    Remove the leaf spring.


54. INSPECT 1ST AND REVERSE BRAKE CLUTCH DISC

  1. Q000777E01
    Using vernier calipers, measure the return spring free length together with the spring seat.

    Standard free length:
    12.9 mm (0.508 in.)


55. REMOVE BRAKE DRUM GASKET

  1. AT04444
    Remove the brake drum gasket.


56. INSPECT PISTON STROKE OF 1ST AND REVERSE BRAKE

  1. AT05258
    Make sure the 1st & reverse brake pistons move smoothly when applying and releasing the compressed air into the transmission case.


57. REMOVE 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY

  1. AT08336E02
    Set SST on the spring retainer, and compress the return spring.
    SST
    09350-30020   (09350-07050, 09350-07070)

  1. Using snap ring pliers, remove the snap ring.

  1. Remove the piston return spring.

  1. Hold the 1st and reverse brake piston by hand, and apply compressed air to the transmission case to remove the 1st and reverse brake piston.


58. REMOVE 1ST AND REVERSE BRAKE PISTON NO.2

  1. AT05375
    Remove the 1st and reverse brake piston.
    If the piston does not pop out with compressed air, lift the piston out with the needle-nose pliers.

  1. Remove the O-ring from the 1st and reverse brake piston.


59. REMOVE BRAKE REACTION SLEEVE

  1. AT08335E01
    Install SST behind the reaction sleeve and gradually lift it out of the transmission case.
    SST
    09350-30020   (09350-07080)

  1. Remove the O-ring from the reaction sleeve.


60. REMOVE 1ST AND REVERSE BRAKE PISTON NO.1

  1. AT08334E01
    Install SST behind the 1st and reverse brake piston No.1, and gradually lift it out of the transmission case.
    SST
    09350-30020   (09350-07090)

  1. Remove the 2 O-rings from the 1st and reverse brake piston No.1.


61. INSPECT AUTOMATIC TRANSMISSION CASE SUB-ASSEMBLY

  1. AT08224
    Using a cylinder gauge, measure the inside diameter of the transmission case rear bushing.

    Maximum inside diameter:
    38.19 mm(1.5035 in.)

    If the inside diameter is greater than the maximum, replace the transmission case.

← COMPONENTS (from Oct 2014)INSPECTION (from Oct 2014) →