2014-2019 Hiace · Service Manual TRANSMISSION

REASSEMBLY

Removal / installation · Vehicles built from Oct 2014


1. BEARING POSITION

D029784E02
Mark
Front Race Diameter Inside / Outside mm (in.)
Thrust Bearing Diameter Inside / Outside mm (in.)
Rear Race Diameter Inside / Outside mm (in.)
A
28.45 (1.120) / 47.3 (1.862)
29.2 (1.15) / 50.2 (1.976)
-
B
28.8 (1.134) / 46.4 (1.827)
28.9 (1.138) / 50.2 (1.976)
-
C
24.7 (0.972) / 41.8 (1.646)
24.2 (0.953) / 47.8 (1.882)
-
D
37.2 (1.465) / 58.8 (2.315)
33.8 (1.331) / 50.0 (1.969)
-
E
36.8 (1.449) / 50.9 (2.004)
33.7 (1.327) / 47.6 (1.874)
-
F
26.0 (1.024) / 48.9 (1.926)
26.0 (1.024) / 46.7 (1.839)
26.8 (1.055) / 47.0 (1.850)
G
-
35.2 (1.386) / 53.6 (2.110)
34.3 (1.350) / 47.8 (1.882)
H
33.7 (1.327) / 47.6 (1.874)
35.5 (1.398) / 47.7 (1.878)
-
I
28.5 (1.122) / 44.2 (1.740)
27.7 (1.091) / 44.2 (1.740)
-
J
-
39.38 (1.550) / 58.1 (2.287)
-

2. FIX AUTOMATIC TRANSMISSION CASE SUB-ASSEMBLY

  1. AT05393
    Install the transmission case in the overhaul attachment.


3. INSTALL 1ST AND REVERSE BRAKE PISTON NO.1

  1. AT08209E05
    Coat 3 new O-rings with ATF.

  1. Install the 2 O-rings on the 1st and reverse brake piston No.1.

  1. Install the O-ring on the reaction sleeve.

  1. Install the 1st and reverse brake piston No.1 to the reaction sleeve.


4. INSTALL BRAKE REACTION SLEEVE

  1. D001243
    Coat new O-ring with ATF, and install it to the reaction sleeve.

  1. With the brake piston No.1 underneath (the rear side), install the brake reaction sleeve and the brake piston No.1 to the transmission case.

    NOTICE:
    Be careful not to damage the O-rings.


5. INSTALL 1ST AND REVERSE BRAKE PISTON NO.2

  1. AT08333E04
    Coat new O-ring with ATF.

  1. Install the O-ring on brake piston No.2.

  1. With the spring seat of the piston upwards (the front side), place the piston in the transmission case.

    NOTICE:
    Be careful not to damage the O-ring.


6. INSTALL 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY

  1. AT05429
    Place the piston return spring onto the 1st and reverse brake piston.

  1. AT08303E02
    Set SST as shown, and compress the return spring with SST.
    SST
    09350-30020   (09350-07050, 09350-07070)

  1. Using a screwdriver, install the snap ring. Make sure the end gap of the snap ring is not aligned with the spring retainer claw.


7. INSPECT PISTON STROKE OF 1ST AND REVERSE BRAKE

8. INSTALL REAR PLANETARY GEAR ASSEMBLY

  1. AT05107
    Install the leaf spring.

  1. AT08208
    Install the flange with the rounded edge facing forward. Reinstall the plates and discs.

    Install in order:
    P = Plate D = Disc
    D - P - D - P - D - P - D - P - D - P - D - P

  1. Install the 2nd brake drum assembly.

  1. AT05784
    Coat the bearing with petroleum jelly and install it onto the case.
    Bearing diameter: 
    Inside
    Outside
    39.38 mm (1.5504 in.)
    58.1 mm (2.2874 in.)

  1. AT07893
    Align the teeth on the flange, the discs and the plates.

  1. AT05785
    Align the splines of the transmission case with the assembled rear planetary gear, the 2nd brake drum, and the 1st and reverse brake pack with the output shaft,

  1. Hold the output shaft with wooden blocks or equivalents.

  1. AT05396E01
    Using SST, install the snap ring.
    SST
    09350-30020   (09350-07060)


9. INSPECT PACK CLEARANCE OF FIRST AND REVERSE BRAKE

10. INSTALL 2ND BRAKE PISTON SLEEVE

  1. AT05787
    Install the brake reaction sleeve.


11. INSTALL BRAKE DRUM GASKET

  1. AT04469
    Coat a new gasket with ATF.

  1. Install the brake drum gasket.


12. INSTALL 1 WAY CLUTCH ASSEMBLY

  1. AT05788
    Install the thrust washer.

  1. Install the 1 way clutch assembly.


13. INSTALL 2ND BRAKE PACK

  1. C114751
    Install the 1.8 mm (0.071 in.) thick plate with the rounded edge side of the plate facing the disc.

  1. Install the plates and discs.

    Plate thickness:
    2.5 mm (0.098 in.)

    Install in order:
    P = Plate D = Disc
    D - P - D - P - D - P - D - P - D - P

  1. Install the flange with the rounded edge of the flange facing the disc.

  1. AT05789
    Using a screwdriver, install the snap ring.


14. INSPECT PACK CLEARANCE OF SECOND BRAKE

15. INSTALL PLANETARY SUN GEAR SUB-ASSEMBLY

  1. AT05790
    While turning the planetary sun gear clockwise, install it into the 1 way clutch.

    HINT:
    Confirm the thrust washer is installed correctly.


16. INSTALL FRONT PLANETARY GEAR ASSEMBLY

  1. Z006795E01
    Coat the bearing and race with petroleum jelly and install them onto the front planetary gear.
    Bearing and race diameter: 

    Inside
    Outside
    Bearing
    35.5 mm (1.398 in.)
    47.7 mm (1.878 in.)
    Race
    33.7 mm (1.327 in.)
    47.6 mm (1.874 in.)

  1. AT05778
    Install the front planetary gear to the sun gear input drum.

  1. AT05777E01
    Using SST, install the snap ring.
    SST
    09350-30020   (09350-07070)

  1. Remove the wooden blocks or equivalent under the output shaft.

  1. Z005135E01
    Coat the race with petroleum jelly, and install it onto the front planetary gear.
    Race diameter: 
    Inside
    Outside
    34.3 mm (1.350 in.)
    47.8 mm (1.882 in.)


17. INSTALL 2ND COAST BRAKE BAND ASSEMBLY

  1. AT05772
    Install the 2nd coast brake band to the case.

  1. Using needle-nose pliers, install the E-ring to the pin.

  1. AT05245
    Install the pin through the brake band.

  1. AT05791
    Using needle-nose pliers, install the E-ring to the pin.


18. INSTALL DIRECT CLUTCH ASSEMBLY
  1. Install the bearing and thrust washer to the forward clutch.

  1. AT05262E01
    Install the direct clutch to the forward clutch.

  1. Z005137E02
    Coat the bearing and the race with petroleum jelly, and install them onto the forward clutch.
    Bearing and race diameter: 

    Inside
    Outside
    Race
    26.0 mm (1.024 in.)
    48.9 mm (1.926 in.)
    Bearing
    26.0 mm (1.024 in.)
    46.7 mm (1.839 in.)

  1. Z005136E02
    Coat the race with the petroleum jelly, and install it onto the front planetary ring gear.
    Race diameter: 

    Inside
    Outside
    Race
    26.8 mm (1.055 in.)
    47.0 mm (1.850 in.)

  1. AT05432
    Align the flukes of the discs in the forward clutch.

  1. Q000838E02
    Align the splines of the front planetary ring gear with the flukes of the discs and install the front planetary ring gear to the forward clutch.


19. INSTALL FRONT PLANETARY RING GEAR SUB-ASSEMBLY

  1. AT08306E02
    Coat the bearing and the race with petroleum jelly, and install them onto the ring gear.
    Bearing and race diameter: 

    Inside
    Outside
    Bearing
    32.6 mm (1.283 in.)
    47.7 mm (1.878 in.)
    Race
    30.6 mm (1.205 in.)
    53.6 mm (2.110 in.)

  1. AT08234
    Install the assembled direct clutch, the forward clutch and the front planetary ring gear into the transmission case.

  1. AT05213
    Using vernier calipers, measure the distance between the sun gear input drum and the direct clutch drum as shown in the illustration.

    Height:
    5.3 to 7.3 mm (0.209 to 0.287 in.)

    If the distance is outside standard, check for an improper installation.

  1. Z005236E02
    Coat the bearing with petroleum jelly and install it onto the forward clutch.
    Bearing diameter: 

    Inside
    Outside
    Bearing
    33.7 mm (1.327 in.)
    47.6 mm (1.874 in.)


20. INSTALL 2ND COAST BRAKE PISTON

  1. AT05086
    Coat 2 new O-rings with ATF and install them to the cover.

  1. Install the spring, the piston assembly and the cover to the case.

  1. AT05127E02
    Using SST, install the snap ring.
    SST
    09350-30020   (09350-07060)


21. INSPECT PISTON STROKE OF 2ND COAST BRAKE

22. INSTALL OVERDRIVE SUPPORT SUB-ASSEMBLY

  1. AT05110E04
    Coat the bearing and race with petroleum jelly, and install it onto the O/D support assembly.
    Bearing and race diameter: 

    Inside
    Outside
    Bearing
    36.8 mm (1.449 in.)
    50.9 mm (2.004 in.)
    Race
    36.8 mm (1.449 in.)
    50.9 mm (2.004 in.)

  1. AT08246E01
    Using 2 bolts of SST, aim the bolt and the oil holes of the O/D support toward the valve body side, and align them with the bolt holes of the transmission case, and insert.
    SST
    09350-30020   (09350-07020)

  1. Temporarily tighten the 2 bolts.

  1. Q000618E02
    Using SST, install the snap ring.
    SST
    09350-30020   (09350-07060)

    HINT:
    Install the snap ring open end toward the valve body.

  1. AT05795
    Torque the 2 bolts.

    Torque:
    25 N*m{ 260 kgf*cm , 19 ft.*lbf }


23. INSPECT OUTPUT SHAFT

24. INSTALL OVERDRIVE BRAKE PACK

  1. AT05781
    Install the 4.0 mm (0.157 in.) thick flange (flat ring) with the rounded edge side of the flange facing the discs.

  1. Install the plates and discs.

    Install in order:
    P = Plate D = Disc
    P - D - P - D - P - D - P - D

  1. Install the flange (stepped ring) with the flat side of the flange facing the disc.

  1. AT08427
    Using a screwdriver, install the snap ring.


25. INSPECT OVERDRIVE BRAKE PISTON

26. INSTALL OVERDRIVE PLANETARY GEAR ASSEMBLY

  1. AT05768
    Coat the bearing and race with petroleum jelly, and install it onto the O/D support.
    Race diameter: 

    Inside
    Outside
    Race
    37.2 mm (1.465 in.)
    58.8 mm (2.315 in.)

  1. AT05761
    Install the O/D planetary ring gear.

  1. AT05797
    Coat the bearing and the race with petroleum jelly, and install them onto the planetary ring gear.
    Bearing and race diameter: 

    Inside
    Outside
    Bearing
    26.0 mm (1.024 in.)
    46.8 mm (1.843 in.)
    Race
    24.2 mm (0.953 in.)
    47.8 mm (1.882 in.)

  1. Z005128
    Coat the race with petroleum jelly, and install it onto the planetary gear.
    Race diameter: 
    Inside
    Outside
    24.7 mm (0.9724 in.)
    41.8 mm (1.646 in.)

  1. AT05759
    Install the O/D planetary gear, O/D direct clutch and one- way clutch.

  1. AT04470E02
    Place SST on the transmission case.
    SST
    09350-36010   (09350-06090)

  1. Using vernier calipers, measure distance between the tops of SST and the clutch drum.

    Standard distance:
    15.5 to 16.5 mm (0.610 to 0.650 in.)

    If the distance is outside the standard, check for an improper installation.

  1. AT08313E02
    Coat the bearing with petroleum jelly and install it onto the O/D direct clutch.
    Bearing and race diameter: 

    Inside
    Outside
    Bearing
    29.2 mm (1.150 in.)
    50.2 mm (1.976 in.)


27. INSTALL OIL PUMP ASSEMBLY

  1. Z005237E02
    Coat the race with petroleum jelly, and install it onto the oil pump.
    Race diameter: 

    Inside
    Outside
    Race
    28.45 mm (1.120 in.)
    47.3 mm (1.862 in.)

  1. Coat a new O-ring with ATF, and install it around the pump body.

  1. Place the oil pump through the input shaft, and align the bolt holes of the pump body with the transmission case.

  1. Hold the input shaft, and lightly press the oil pump body to slide the oil seal rings into the O/D direct clutch drum.

    NOTICE:
    Do not push on the oil pump strongly, or the oil seal ring will stick to the direct clutch drum.

  1. AT05799
    Install the 7 bolts.

    Torque:
    22 N*m{ 220 kgf*cm , 16 ft.*lbf }


28. INSPECT INPUT SHAFT SUB-ASSEMBLY

29. INSPECT INDIVIDUAL PISTON OPERATION INSPECTION

30. INSTALL MANUAL VALVE LEVER SHAFT OIL SEAL

  1. AT05238E02
    Using SST and a hammer, drive in 2 new manual valve lever shaft oil seals.
    SST
    09350-30020   (09350-07110)


31. INSTALL MANUAL VALVE LEVER SUB-ASSEMBLY

  1. Q000775E01
    Install a new spacer to the manual valve lever.

  1. Install the manual valve lever shaft to the transmission case through the manual valve lever.

  1. AT05405
    Using a hammer, drive in a new pin.

  1. D006523
    Align the manual valve lever indentation with the spacer hole and stake them with a punch.

  1. Make sure the shaft rotates smoothly.


32. INSTALL PARKING LOCK PAWL SHAFT

  1. Q000776E02
    Install the E-ring to the shaft.

  1. Install the parking lock pawl, the shaft and the spring.


33. INSTALL PARKING LOCK ROD SUB-ASSEMBLY

  1. Z006797
    Connect the parking lock rod to the manual valve lever.


34. INSTALL PARKING LOCK PAWL BRACKET

  1. AT05406
    Install the parking lock pawl bracket with the 3 bolts.

    Torque:
    7.4 N*m{ 75 kgf*cm , 65 in.*lbf }

  1. Z005222E02
    Shift the manual valve lever to the P position, and confirm that the planetary ring gear is correctly locked up by the lock pawl.


35. INSTALL C-0 ACCUMULATOR PISTON

  1. AT05010E02
    Coat new O-ring with ATF, and install them to the piston.

  1. D028075
    Install the 2 springs and the accumulator piston to the hole.
    Accumulator spring: 
    Spring
    Free length outer diameter mm (in.)
    Color
    C0 Inner
    46.0 mm (1.811 in.)
    14.02 mm (0.552 in.)
    Yellow
    C0 Outer
    74.6 mm (2.937 in.)
    20.9 mm (0.823 in.)
    Orange


36. INSTALL B-0 ACCUMULATOR PISTON

  1. AT05010E02
    Coat new O-rings with ATF, and install them to the piston.

  1. D028074
    Install the spring and the accumulator piston to the hole.
    Accumulator spring: 
    Spring
    Free length outer diameter mm (in.)
    Color
    B0
    62.0 mm (2.441 in.)
    16.0 mm (0.630 in.)
    Green


37. INSTALL C-2 ACCUMULATOR PISTON

  1. AT05010E02
    Coat new O-rings with ATF, and install them to the piston.

  1. D028073
    Install the 2 springs and the accumulator piston to the hole.
    Accumulator spring: 
    Spring
    Free length outer diameter mm (in.)
    Color
    C2 Inner
    42.1 mm (1.657 in.)
    14.7 mm (0.579 in.)
    Pink
    C2 Outer
    68.53 mm (2.698 in.)
    20.2 mm (0.795 in.)
    Blue


38. INSTALL B-2 ACCUMULATOR PISTON

  1. AT05010E02
    Coat new O-rings with ATF, and install them to the piston.

  1. D028072
    Install the spring and the accumulator piston to the hole.
    Accumulator spring: 
    Spring
    Free length outer diameter mm (in.)
    Color
    B2
    70.5 mm (2.776 in.)
    19.9 mm (0.783 in.)
    Light green


39. INSTALL CHECK BALL BODY

  1. AT05098E02
    Install the check ball body and spring.


40. INSTALL TRANSMISSION VALVE BODY ASSEMBLY

  1. AT08393E02
    Align the groove of the manual valve with the pin of the lever.

  1. D029011E02
    Install the 20 bolts.

    Torque:
    11 N*m{ 112 kgf*cm , 8 ft.*lbf }

    Bolt length:
    Bolt A:
    23 mm (0.91 in.)
    Bolt B:
    28 mm (1.10 in.)
    Bolt C:
    36 mm (1.42 in.)


41. INSTALL TRANSMISSION WIRE

  1. G021842
    Coat a new O-ring with ATF, and install it to the transmission wire.

  1. Install the solenoid wiring to the case, and then install the bolt.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

  1. C058460
    Connect the connectors to each shift solenoid valve.


42. INSTALL VALVE BODY OIL STRAINER ASSEMBLY
  1. Using a plastic hammer, install the pipe into the position.

    NOTICE:
    Be careful not to bend or damage the pipes.

  1. C114750E01
    Install the oil strainer with the 4 bolts.

    Torque:
    11 N*m{ 112 kgf*cm , 8 ft.*lbf }

    Bolt length:
    Bolt A:
    16 mm (0.63 in.)
    Bolt B:
    20 mm (0.79 in.)
    Bolt C:
    28 mm (1.10 in.)


43. INSTALL TRANSMISSION OIL CLEANER MAGNET

  1. D029014
    Install the 3 magnets on the oil pan.


44. INSTALL AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY

  1. AT01362E03
    Remove any FIPG material and be careful not to drop oil on the contacting surfaces of the transmission case and the oil pan.

  1. Apply FIPG to the oil pan.

    FIPG:
    Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent

  1. Install the oil pan with the 19 bolts.

    Torque:
    7.4 N*m{ 75 kgf*cm , 65 in.*lbf }


45. INSTALL SENSOR ROTOR

  1. C114748
    Using a snap ring expander, install the front side snap ring.

  1. Install the key and sensor rotor.

  1. Using a snap ring expander, install the rear side snap ring.


46. INSTALL EXTENSION HOUSING DUST DEFLECTOR

  1. C106493
    Using a screwdriver and hammer, install new extension housing dust deflector.


47. INSTALL AUTOMATIC TRANSMISSION EXTENSION HOUSING OIL SEAL

  1. C106499E02
    Using SST and a hammer, install a new extension housing oil seal.
    SST
    09950-60020   (09951-00580)
    09950-70010   (09951-07100)

    Oil seal in depth:
    5.8 to 6.2 mm (0.228 to 0.244 in.)


48. INSTALL EXTENSION HOUSING BUSH APPLY TUBE

  1. C114745E04
    Install the extension housing bush apply tube.


49. INSTALL EXTENSION HOUSING BUSH APPLY TUBE GASKET

  1. C114745E05
    Install the extension housing bush apply tube gasket.


50. INSTALL EXTENSION HOUSING SUB-ASSEMBLY

  1. C114744
    Apply seal packing or equivalent to the 6 bolts.

    Seal packing:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent

  1. Install the extension housing and a new gasket to the case with the 6 bolts.

    Torque:
    36 N*m{ 370 kgf*cm , 27 ft.*lbf }

    HINT:
    The 2 lower bolts are shorter.


51. INSTALL TRANSMISSION REVOLUTION SENSOR

  1. C114743
    Coat a new O-ring with ATF, and install it to the sensor.

  1. Install the revolution sensor with the bolt.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }


52. INSTALL AUTOMATIC TRANSMISSION HOUSING

  1. C114749
    Install the transmission housing with the 6 bolts.

    Torque:
    14 mm bolt:
    34 N*m (345 kgf*cm, 25 ft.*lbf)
    17 mm bolt:
    57 N*m (580 kgf*cm, 42 ft.*lbf)


53. INSTALL SPEED SENSOR

  1. Q003894
    Coat a new O-ring with ATF, and install it to the sensor.

  1. Install the speed sensor.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }


54. INSTALL TEMPERATURE SENSOR

  1. D005532
    Coat a new O-ring with ATF, and install it to the temperature sensor.

  1. Install the temperature sensor.

    Torque:
    15 N*m{ 160 kgf*cm , 11 ft.*lbf }


55. INSTALL OIL COOLER TUBE UNION
  1. Coat a new O-rings with ATF, and install them to the unions.

  1. Install the oil cooler tube unions.

    Torque:
    29 N*m{ 300 kgf*cm , 22 ft.*lbf }


56. INSTALL PARK/NEUTRAL POSITION SWITCH ASSEMBLY

  1. C101836E01
    Install the park/neutral position switch onto the manual valve lever shaft, and temporarily tighten the adjusting bolt.

  1. Install the nut stopper and a new lock washer. Install the nut.

    Torque:
    6.9 N*m{ 70 kgf*cm , 61 in.*lbf }

  1. Using the control shaft lever, fully turn the manual lever shaft back, and then return 2 notches. It is now in neutral.

  1. C101839E01
    Align the neutral basic line with the switch groove, and tighten the adjusting bolt.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf }

  1. Bend the tabs of the lock washer.

    HINT:
    Bend at least 2 of the lock washer tabs.


57. INSTALL TRANSMISSION CASE PLUG ASSEMBLY

  1. D005553
    Coat a new O-ring with ATF, and install it to the plug.

  1. Install the cable to the case with the bolt.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }


58. INSTALL TRANSMISSION CONTROL SHAFT LEVER LH
  1. Install the transmission control shaft lever and the washer. Install the nut.

    Torque:
    16 N*m{ 160 kgf*cm , 12 ft.*lbf }


59. INSTALL BREATHER PLUG HOSE
  1. Install the breather plug hose.


60. INSTALL DRAIN (ATM) PLUG SUB-ASSEMBLY

Torque:
20 N*m{ 205 kgf*cm , 15 ft.*lbf }

← INSPECTION (from Oct 2014)COMPONENTS (from Oct 2014) →