2014-2019 Hiace · Service Manual ENGINE

INSPECTION

Inspection · Vehicles built from Oct 2014


INSPECT STARTER ASSEMBLY (for 2.0 kW Type)

NOTICE:
The following tests must be performed within 3 to 5 seconds to prevent the coil from burning out.

  1. Perform the pull-in test.

    1. A051215E01
      Disconnect the field coil lead wire from terminal C.

    2. S004242E01
      Connect the battery to the magnetic switch as shown in the illustration. Check that the clutch pinion gear is extended.

  1. Perform the hold test.

    1. S004243E01
      Disconnect the negative (-) lead from terminal C while sustaining the above condition (a). Check that the pinion gear remains extended.

  1. Check the return operation.

    1. S004244
      Disconnect the negative (-) lead from the starter body. Check that the clutch pinion gear returns inward.

  1. Perform the operation test without any load.

    1. A051215
      Connect the field coil lead wire to terminal C.

      Torque:
      5.9 N*m{ 60 kgf*cm , 52 in.*lbf }

    2. S004245E01
      Clamp the starter in a vise.

    3. Connect the battery and ammeter to the starter as shown in the illustration.

    4. Check that the ammeter indicates the specified current.

      Standard current:
      100 A or less at 11.5 V


INSPECT STARTER ASSEMBLY (for 2.2 kW Type)

NOTICE:
These tests must be performed within 3 to 5 seconds to prevent the coil from burning out.


A121979E01

  1. Perform pull-in test.

    1. Remove the nut, and then disconnect the field coil core from terminal C.

    2. Connect the battery to the magnet starter switch as shown in the illustration. Then check that the clutch pinion gear moves outward.

      A122799E01
      If the clutch pinion gear does not move, replace the magnet starter switch assembly.

  1. Perform holding test.

    1. When the battery is connected as above with the clutch pinion gear out, disconnect the negative (-) lead from terminal C. Check that the pinion gear remains out.

      A121976E01
      If the clutch pinion gear returns inward, replace the magnet starter switch assembly.

  1. Inspect clutch pinion gear return.

    1. Disconnect the negative (-) lead from the starter body. Check that the clutch pinion gear returns inward.

      A121977E01
      If the clutch pinion gear does not return inward, replace the magnet starter switch assembly.

  1. Perform operation test without load.

    1. Connect the field coil lead wire to terminal C with the nut.

      Torque:
      8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

    2. Mount the starter in a vise between aluminum plates.

    3. Connect the battery and ammeter to the starter as shown in the illustration.

      A121978E01

    4. Check that the starter rotates smoothly and steadily while the pinion gear is moving outward. Then measure the current.

      Standard current:
      123 A or less at 11.5 V

      If the result is not as specified, replace the starter assembly.


INSPECT STARTER ASSEMBLY (for 2.7 kW Type)

NOTICE:
The following tests must be performed within 3 to 5 seconds to prevent the coil from burning out.

  1. Perform the pull-in test.

    1. A051215E01
      Disconnect the field coil lead wire from terminal C.

    2. S004242E01
      Connect the battery to the magnetic switch as shown in the illustration. Check that the clutch pinion gear is extended.

  1. Perform the hold test.

    1. S004243E01
      Disconnect the negative (-) lead from terminal C while sustaining the above condition (a). Check that the pinion gear remains extended.

  1. Check the return operation.

    1. S004244
      Disconnect the negative (-) lead from the starter body. Check that the clutch pinion gear returns inward.

  1. Perform the operation test without any load.

    1. A051215
      Connect the field coil lead wire to terminal C.

      Torque:
      24 N*m{ 245 kgf*cm , 18 ft.*lbf }

    2. S004245E01
      Clamp the starter in a vise.

    3. Connect the battery and ammeter to the starter as shown in the illustration.

    4. Check that the ammeter indicates the specified current.

      Standard current:
      180 A or less at 11.5 V

← SYSTEM DIAGRAM (from Oct 2014)PARTS LOCATION (from Oct 2014) →