2014-2019 Hiace · Service Manual SUSPENSION & AXLE

REPLACEMENT

Removal / installation · Vehicles built from Oct 2014


1. REMOVE REAR WHEEL

2. REMOVE REAR BRAKE DRUM SUB-ASSEMBLY

  1. Release the parking brake lever, and remove the brake drum.

    C263541E01

    Text in Illustration 
    *A
    for 295 mm Drum
    *B
    for 254 mm Drum

    HINT:
    If the brake drum cannot be removed easily, perform the following steps.

  1. Remove the hole plug and insert a screwdriver through the hole in the backing plate, and hold the automatic adjusting lever away from the adjuster.

  1. Using another screwdriver, contract the brake shoe adjuster by turning the adjusting wheel.


3. REMOVE REAR AXLE BRAKE DRUM GASKET

4. REMOVE AUTOMATIC ADJUST LEVER

  1. for 254 mm drum:

    1. C102605
      Remove the automatic adjust lever and the tension spring.


5. SEPARATE PARKING BRAKE SHOE STRUT SET

  1. for 254 mm drum:

    1. C231698E01
      Using SST, remove the upper side tension spring from the brake shoe.
      SST
      09703-30011  

  1. for 295 mm drum:

    1. C263526E01
      Using SST, remove the upper side tension spring from the brake shoe.
      SST
      09703-30011  


6. REMOVE FRONT BRAKE SHOE

  1. for 254 mm drum:

    1. C102600
      Using a needle-nose pliers, remove the anchor side tension spring.

    2. C102601E01
      Using SST, remove the cup, shoe hold-down sprig and pin.
      SST
      09718-00011  

    3. C264220E02
      Remove the parking brake shoe lower strut.
      Text in Illustration 
      *A
      LH Side
      *B
      RH Side

    4. Separate the brake shoe return spring, and remove the front brake shoe.

  1. for 295 mm drum:

    1. C263527E01
      Using SST, remove the cup, shoe hold-down sprig and pin.
      SST
      09718-00011  

    2. Separate the brake shoe return spring, and remove the front brake shoe.


7. REMOVE REAR BRAKE SHOE

  1. for 254 mm drum:

    1. C102603E01
      Using SST, remove the cup, shoe hold-down sprig and pin.
      SST
      09718-00011  

    2. C102606
      Disconnect the parking brake cable No. 3 and remove the rear brake shoe.

  1. for 295 mm drum:

    1. C263528E01
      Using SST, remove the cup, shoe hold-down sprig and pin.
      SST
      09718-00011  

    2. Remove the tension spring.

    3. C263529
      Disconnect the parking brake cable No. 3 and remove the rear brake shoe.


8. REMOVE PARKING BRAKE SHOE STRUT SET

  1. for 254 mm drum:

    1. C102607E02
      Using a screwdriver, remove the C-washer, brake shoe lever, rear cushion lever and brake shoe strut set from the brake shoe.
      Text in Illustration 
      *1
      Brake Shoe Lever
      *2
      Brake Shoe Strut Set
      *3
      Rear Brake Shoe
      *4
      Rear Cushion Lever
      *5
      C-washer

    2. Remove the adjusting bolt and tension spring from the brake shoe strut set.

  1. for 295 mm drum:

    1. C263530E01
      Remove the brake shoe strut set.
      Text in Illustration 
      *1
      Rear Brake Shoe
      *2
      Brake Shoe Strut Set
      *3
      Brake Shoe Lever
      *4
      Automatic Adjust Lever
      *5
      C-washer
      *6
      E-ring

    2. Using a screwdriver, remove the E-ring and automatic adjust lever.

    3. Using a screwdriver, remove the C-washer and brake shoe lever from the brake shoe.


9. REMOVE REAR AXLE HUB BOLT

  1. C102300E01
    Install a washer and nut to the bolt as shown in the illustration.

  1. Using SST and a screwdriver or an equivalent to hold the hub sub-assembly, remove the rear axle hub bolt.

    SST
    09650-17011  

    NOTICE:
    Do not damage the threads of the hub bolts.


10. INSTALL REAR AXLE HUB BOLT

  1. C102369E01
    Install a washer and nut to a new bolt as shown in the illustration.

  1. Using a screwdriver or an equivalent to hold the hub sub assembly, install the rear axle hub bolt by tightening the nut.

    NOTICE:
    Do not damage the threads of the hub bolts.


11. INSTALL PARKING BRAKE SHOE STRUT SET

  1. F042695E03
    Apply the high temperature grease to the adjusting bolt.
    Text in Illustration 
    *1
    High temperature grease

  1. Install the tension spring to the shoe strut set.


12. INSTALL REAR BRAKE SHOE

  1. for 254 mm drum:

    1. C102607E02
      Using pliers, install the rear brake shoe, shoe strut set, rear cushion lever and shoe lever with a new C-washer.
      Text in Illustration 
      *1
      Brake Shoe Lever
      *2
      Brake Shoe Strut Set
      *3
      Rear Brake Shoe
      *4
      Rear Cushion Lever
      *5
      C-washer

    2. C102606
      Connect the parking brake cable No. 3 to the front brake shoe.

    3. C102603E01
      Using SST, install the rear brake shoe, pin, shoe hold down spring and shoe hold down cup.
      SST
      09718-00011  

  1. for 295 mm drum:

    1. C263530E01
      Install the rear brake shoe, brake shoe strut set and shoe lever with a new C-washer.
      Text in Illustration 
      *1
      Rear Brake Shoe
      *2
      Brake Shoe Strut Set
      *3
      Brake Shoe Lever
      *4
      Automatic Adjust Lever
      *5
      C-washer
      *6
      E-ring

    2. Install a new E-ring and the automatic adjust lever.

    3. C263529
      Connect the parking brake cable No. 3 to the front brake shoe.

    4. C263525
      Install the tension spring as shown in the illustration.

    5. C263528E01
      Using SST, install the rear brake shoe, pin, shoe hold down spring and shoe hold down cup.
      SST
      09718-00011  


13. INSTALL FRONT BRAKE SHOE

  1. for 254 mm drum:

    1. Install the return spring to each brake shoe.

    2. C102604E01
      Using SST, install the front brake shoe, pin, shoe hold down spring and shoe hold down cup.
      SST
      09718-00011  

    3. C264855E02
      Install the brake shoe lower strut.
      Text in Illustration 
      *A
      LH Side
      *B
      RH Side

      NOTICE:
      Make sure that the shoe lower strut and brake rear cushion lever are securely engaged.

    4. C102600
      Using needle-nose pliers, install the tension spring.

  1. for 295 mm drum:

    1. C263527E01
      Using SST, install the front brake shoe, pin, shoe hold down spring and shoe hold down cup.
      SST
      09718-00011  

    2. Install the return spring to each brake shoe.


14. CONNECT PARKING BRAKE SHOE STRUT SET

  1. for 254 mm drum:

    1. C231698E01
      Using SST, install the upper side tension spring.
      SST
      09703-30011  

  1. for 295 mm drum:

    1. C263526E01
      Using SST, install the upper side tension spring.
      SST
      09703-30011  


15. INSTALL AUTOMATIC ADJUST LEVER

  1. for 254 mm drum:

    1. C102605
      Install the automatic adjust lever and tension spring.

      NOTICE:
      Make sure to install the automatic adjust lever between the groove of the shoe strut set and brake shoe.


16. INSPECT REAR DRUM BRAKE

  1. Check the each part is installed properly.

    C264221E02

    C263532E01

    Text in Illustration 
    *A
    for 254 mm Drum
    *B
    for 295 mm Drum
    *C
    LH Side
    *D
    RH Side
    *a
    Front
    -
    -

    NOTICE:
    There should be no oil or grease adhering to the friction surfaces of the shoe lining and drum.

  1. If they are not installed correctly, reinstall them as shown in the illustration.


17. INSTALL REAR AXLE BRAKE DRUM GASKET
  1. Install the new brake drum gasket to the rear axle shaft.


18. INSTALL REAR BRAKE DRUM SUB-ASSEMBLY

19. ADJUST REAR DRUM BRAKE SHOE CLEARANCE

  1. Using a screwdriver from a service hole, turn the adjuster to expand the shoes so that the brake shoes touch the brake drum.

    C263542E01

    Text in Illustration 
    *A
    for 295 mm Drum
    *B
    for 254 mm Drum

  1. Using another screwdriver, push up the automatic adjust lever and turn the adjuster to contract the shoes so that the brake shoe does not touch the brake drum. Then turn the adjuster another 180 degrees to further contract the shoes.

    C263541E01

    Text in Illustration 
    *A
    for 295 mm Drum
    *B
    for 254 mm Drum

  1. Install the hole plug.


20. INSTALL REAR WHEEL

Torque:
100 N*m{ 1,020 kgf*cm , 74 ft.*lbf }

← COMPONENTS (from Oct 2014)COMPONENTS (from Oct 2014) →