2014-2019 Hiace · Service Manual ENGINE

P0102 Mass Air Flow Circuit Low

Diagnostic trouble codes · Vehicles built from Jan 2017

Also covers:

Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Nov 2015 Dec 2015 – Mar 2016 Apr 2016 – Dec 2016 from Jan 2017

DESCRIPTION

The intake mass air flow meter assembly consists of a platinum hot wire, temperature sensor and control circuit installed in a plastic housing. The temperature sensor (located in the intake air by-pass of the housing) detects the intake air temperature.
There is little variation in the output from the intake mass air flow meter assembly, as it is hardly affected by the resistance of the wire harness.
The internal circuit of the intake mass air flow meter assembly contains a hot wire and cold wire. A voltage is output through a bridge circuit (refer to the illustration) indicating the cooling of the hot wire according to the intake air amount. This voltage is then converted into a periodic signal by the periodic signal conversion circuit and output to the ECM. The frequency varies between approximately 1945 and 8500 Hz depending on the air flow rate. The ECM calculates the mass air flow rate based on this frequency.
A221589E01
P0102 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
3 seconds after engine is started
Mass air flow meter signal frequency is less than 850 Hz with the engine speed at 5000 rpm or less for 3 seconds (1 trip detection logic).
  1. Open or short in mass air flow meter circuit
  2. Mass air flow meter
  3. ECM
P0103 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
3 seconds after engine is started
Mass air flow meter signal frequency is more than 9800 Hz with the engine speed at 5000 rpm or less for 3 seconds (1 trip detection logic).
  1. Open or short in Mass air flow meter circuit
  2. Mass air flow meter
  3. ECM
Related Data List 
DTC No.
Data List
P0102
MAF
P0103

HINT:
  1. If DTC P0102 is stored, the following symptoms may appear (as the ECM mistakenly determines that there is less air than the actual intake air amount, EGR is decreased according to the target EGR):
    1. Combustion noise worsens
  2. If DTC P0103 is stored, the following symptoms may appear (as the ECM mistakenly determines that there is more air than the actual intake air amount, EGR is increased according to the target EGR):
    1. Misfire
    2. White smoke
    3. Black smoke


WIRING DIAGRAM

A319596E02

INSPECTION PROCEDURE

NOTICE:
  1. After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
  2. Inspect the fuses of circuits related to this system before performing the following inspection procedure.

HINT:
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


1. CHECK MASS AIR FLOW METER (POWER SOURCE CIRCUIT)
A127724E82
  1. Disconnect the mass air flow meter connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A3-3 (+B) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Mass Air Flow Meter)

  1. Reconnect the mass air flow meter connector.



NG
Go to step 3
OK


2. CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
  1. Disconnect the mass air flow meter connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A3-5 (FG) - D98-65 (VG)
    Always
    Below 1 Ω
    A3-4 (E2G) - D98-64 (EVG)
    Always
    Below 1 Ω
    A3-5 (FG) or D98-65 (VG) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the mass air flow meter connector.

  1. Reconnect the ECM connector.



OK
Go to step 6

NG
Go to step 4
3. CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ENGINE ROOM RELAY BLOCK)
  1. Disconnect the mass air flow meter connector.

  1. Remove the No. 1 integration relay from the No. 1 engine room relay block and junction block assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A3-3 (+B) - 10B-4
    Always
    Below 1 Ω
    A3-3 (+B) or 10B-4 - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the mass air flow meter connector.

  1. Reinstall the No. 1 integration relay.



OK
Go to step 5

NG
Go to step 4
4. REPAIR OR REPLACE HARNESS OR CONNECTOR
  1. Repair or replace the harness or connector.



NEXT
Go to step 9
5. CHECK ECM POWER SOURCE CIRCUIT
  1. Check the ECM power source circuit (Click here).



NEXT
Go to step 9
6. REPLACE MASS AIR FLOW METER
  1. Replace the mass air flow meter (Click here).


NEXT


7. CHECK WHETHER DTC OUTPUT RECURS (DTC P0102 or P0103)
  1. Connect the GTS to the DLC3.

  1. Clear the DTCs (Click here).

  1. Start the engine and wait for 3 seconds or more.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    P0102 or P0103 is output
    A
    No DTC is output
    B



B
END
A


8. REPLACE ECM
  1. Replace the ECM (Click here).


NEXT


9. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the GTS to the DLC3.

  1. Clear the DTCs (Click here).

  1. Start the engine and wait for 3 seconds or more.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Confirm that the DTC is not output again.


NEXT

END


← P0102 Mass Air Flow Circuit Low (+ P0103) (Apr 2016 – Dec 2016)P0106 Manifold Absolute Pressure Circuit Problem (Oct 2014 – Dec 2014) →