2014-2019 Hiace · Service Manual ENGINE

P0116 Engine Coolant Temperature Circuit Range / Performance

Diagnostic trouble codes · Vehicles built Jan 2015 – Nov 2015

Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Nov 2015 Dec 2015 – Mar 2016 Apr 2016 – Dec 2016 from Jan 2017

DESCRIPTION

A thermistor is built into the engine coolant temperature sensor and it changes its resistance value according to the engine coolant temperature.
The structure of the sensor and connection to the ECM is the same as that of the intake air temperature sensor.
P0116 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
City driving for 10 minutes or more after engine start with engine coolant temperature between -40°C (-40°F) and 60°C (140°F)
The engine coolant temperature is between -40°C (-40°F) and 60°C (140°F) at engine start, and conditions (a) and (b) are met (2 trip detection logic):
(a) Vehicle is driven at varying speeds (accelerating and decelerating) for 600 seconds.
(b) Engine coolant temperature remains within 3°C (5.4°F) of the engine starting temperature.
Engine coolant temperature sensor
City driving for 10 minutes or more after engine start with engine coolant temperature higher than 60°C (140°F)
The engine coolant temperature is higher than 60°C (140°F) at engine start, and conditions (a) and (b) are met (6 trip detection logic):
(a) Vehicle is driven at varying speeds (accelerating and decelerating) for 600 seconds.
(b) Engine coolant temperature remains within 1°C (1.8°F) of the engine starting temperature.
Related Data List 
DTC No.
Data List
P0116
Coolant Temp

HINT:
  1. If DTC P0116 is stored, the following symptoms may appear:
    1. Misfire
    2. Combustion noise
    3. Black smoke
    4. White smoke
    5. Lack of power


MONITOR DESCRIPTION

The engine coolant temperature sensor is used to monitor the engine coolant temperature. The engine coolant temperature sensor has a thermistor that varies its resistance depending on the temperature of the engine coolant. When the coolant temperature is low, the resistance of the thermistor increases. When the temperature is high, the resistance drops. The variations in resistance are reflected in the voltage output from the sensor. The ECM monitors the sensor voltage and uses this value to calculate the engine coolant temperature. When the sensor voltage output varies slightly, the ECM interprets this as a fault in the engine coolant temperature sensor and stores a DTC.
Examples:
  1. Upon starting the engine, the engine coolant temperature is between -40°C (-40°F) and 60°C (140°F). If, after driving for a few minutes, the engine coolant temperature still remains within 3°C (5.4°F) of the starting temperature, a DTC is stored (2 trip detection logic).
  2. Upon starting the engine, the engine coolant temperature is higher than 60°C (140°F). If, after driving for a few minutes, the engine coolant temperature still remains within 1°C (1.8°F) of the starting temperature, a DTC is stored (6 trip detection logic).

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


1. CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0116)
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON and turn the GTS on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    P0116 is output
    A
    P0116 and other DTCs are output
    B



B
GO TO DTC CHART (Click here)
A


2. REPLACE ENGINE COOLANT TEMPERATURE SENSOR
  1. Replace the engine coolant temperature sensor (Click here).


NEXT


3. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON and turn the GTS on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.

  1. Start the engine.

  1. Run the engine at 2500 rpm with no load.

  1. Check that "Coolant Temp" changes by 1°C (1.8°F) or more within 10 minutes while idling the engine.


NEXT

END


← P0116 Engine Coolant Temperature Circuit Range / Performance (Oct 2014 – Dec 2014)P0116 Engine Coolant Temperature Circuit Range / Performance (Dec 2015 – Mar 2016) →