2014-2019 Hiace · Service Manual ENGINE

P2121 Throttle / Pedal Position Sensor / Switch "D" Circuit Range / Performance

Diagnostic trouble codes · Vehicles built Jan 2015 – Nov 2015

Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Nov 2015 Dec 2015 – Mar 2016 Apr 2016 – Dec 2016 from Jan 2017

DESCRIPTION

Refer to DTC P2120 (Click here).
P2121 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Ignition switch ON
  1. Accelerator pedal fully released for 3 seconds
  2. Accelerator pedal depressed partway for 3 seconds
  3. Accelerator pedal fully depressed for 3 seconds
The difference between VPA and VPA2 is less than 0.4 V, or more than 1.2 V for 0.5 seconds (1 trip detection logic).
  1. Accelerator pedal position sensor circuit
  2. Accelerator pedal position sensor
  3. ECM
Related Data List 
DTC No.
Data List
P2121
  1. Accel Position
  2. Accel Sens. No.1 Volt %
  3. Accel Sens. No.2 Volt %

WIRING DIAGRAM

Refer to DTC P2120 (Click here).

INSPECTION PROCEDURE

NOTICE:
After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).

HINT:
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


1. READ VALUE USING GTS (ACCELERATOR PEDAL POSITION SENSOR)

  1. C129061E03
    Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON and turn the GTS on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Accel Sens. No.1 Volt % and Accel Sens. No.2 Volt %.

  1. Read the values.

    Standard Voltage:
    Accelerator Pedal
    Accel Sens. No.1 Volt %
    Accel Sens. No.2 Volt %
    Released
    10 to 22%
    24 to 40%
    Depressed
    52 to 90%
    68 to 99%

    Text in Illustration 
    *1
    Accelerator Pedal Assembly
    *a
    Depressed
    *b
    Released
    Result 
    Result
    Proceed to
    NG
    A
    OK
    B



B
Go to step 7
A


2. CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL POSITION SENSOR - ECM)
  1. Disconnect the accelerator pedal position sensor connector.

  1. Disconnect the ECM connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    B1-1 (VCP2) - B72-57 (VCP2)
    Always
    Below 1 Ω
    B1-2 (EPA2) - B72-58 (EPA2)
    Always
    Below 1 Ω
    B1-3 (VPA2) - B72-54 (VPA2)
    Always
    Below 1 Ω
    B1-4 (VCPA) - B72-55 (VCPA)
    Always
    Below 1 Ω
    B1-5 (EPA) - B72-56 (EPA)
    Always
    Below 1 Ω
    B1-6 (VPA) - B72-53 (VPA)
    Always
    Below 1 Ω
    B1-1 (VCP2) or B72-57 (VCP2) - Body ground
    Always
    10 kΩ or higher
    B1-2 (EPA2) or B72-58 (EPA2) - Body ground
    Always
    10 kΩ or higher
    B1-3 (VPA2) or B72-54 (VPA2) - Body ground
    Always
    10 kΩ or higher
    B1-4 (VCPA) or B72-55 (VCPA) - Body ground
    Always
    10 kΩ or higher
    B1-5 (EPA) or B72-56 (EPA) - Body ground
    Always
    10 kΩ or higher
    B1-6 (VPA) or B72-53 (VPA) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the accelerator pedal position sensor connector.

  1. Reconnect the ECM connector.



NG
Go to step 6
OK


3. REPLACE ACCELERATOR PEDAL ROD ASSEMBLY
  1. Replace the accelerator pedal rod assembly (Click here).


NEXT


4. CHECK WHETHER DTC OUTPUT RECURS (DTC P2121)
  1. Connect the GTS to the DLC3.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch to ON.

  1. Fully release the accelerator pedal for 3 seconds or more, then depress it partway for 3 seconds or more, and then fully depress it for 3 seconds or more.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    P2121 is output
    A
    No DTC is output
    B



B
END
A


5. REPLACE ECM
  1. Replace the ECM (Click here).



NEXT
Go to step 7
6. REPAIR OR REPLACE HARNESS OR CONNECTOR
  1. Repair or replace the harness or connector.


NEXT


7. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the GTS to the DLC3.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON.

  1. Fully release the accelerator pedal for 3 seconds or more, then depress it partway for 3 seconds or more, and then fully depress it for 3 seconds or more.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Confirm that the DTC is not output again.


NEXT

END


← P2121 Throttle / Pedal Position Sensor / Switch "D" Circuit Range / Performance (Oct 2014 – Dec 2014)P2121 Throttle / Pedal Position Sensor / Switch "D" Circuit Range / Performance (Dec 2015 – Mar 2016) →