2014-2019 Hiace · Service Manual TRANSMISSION

INSPECTION

Inspection · Vehicles built Oct 2014 – Dec 2016

Versions by build date: Oct 2014 – Dec 2016 from Jan 2017


INSPECT 1ST GEAR THRUST CLEARANCE

  1. C274866
    Using a dial indicator, measure the thrust clearance of the 1st gear.

    Standard clearance:
    0.20 to 0.45 mm (0.0079 to 0.0177 in.)


INSPECT 2ND GEAR THRUST CLEARANCE

  1. Z003552E11
    Using a dial indicator, measure the thrust clearance of the 2nd gear.

    Standard clearance:
    0.10 to 0.25 mm (0.0039 to 0.0098 in.)


INSPECT 3RD GEAR THRUST CLEARANCE

  1. D026046E02
    Using a feeler gauge, measure the thrust clearance of the 3rd gear.

    Standard clearance:
    0.10 to 0.25 mm (0.0039 to 0.0098 in.)


INSPECT 1ST GEAR RADIAL CLEARANCE

  1. D026047
    Using a dial indicator, measure the radial clearance of the 1st gear.

    Standard clearance:
    0.020 to 0.073 mm (0.0008 to 0.0029 in.)

    If the clearance is not within the specified values, replace the 1st gear needle roller bearing with a new one.


INSPECT 2ND GEAR RADIAL CLEARANCE

  1. D026048
    Using a dial indicator, measure the radial clearance of the 2nd gear.

    Standard clearance:
    0.015 to 0.068mm (0.0006 to 0.0027 in.)

    If the clearance is not within the specified values, replace the 2nd gear needle roller bearing with a new one.


INSPECT 3RD GEAR RADIAL CLEARANCE

  1. D026049
    Using a dial indicator, measure the radial clearance of the 3rd gear.

    Standard clearance:
    0.015 to 0.068 mm (0.0006 to 0.0027 in.)

    If the clearance is not within the specified values, replace the 3rd gear needle roller bearing with a new one.


INSPECT OUTPUT SHAFT

  1. D029121
    Using a dial indicator, measure the runout of the output shaft.

    Maximum runout:
    0.03 mm (0.0012 in.)

    If the runout is greater than the maximum, replace the output shaft with a new one.

  1. G038893E01
    Using a micrometer, measure the outer diameter of the output shaft at points A, B and C.

    Standard diameter:
    38.979 to 38.995 mm (1.5334 to 1.5352 in.) for A
    46.984 to 47.000 mm (1.8498 to 1.8504 in.) for B
    37.984 to 38.000 mm (1.4954 to 1.4961 in.) for C

    Minimum diameter:
    38.979 mm (1.5334 in.) for A
    46.984 mm (1.8498 in.) for B
    37.984 mm (1.4954 in.) for C

    If the outer diameter is less than the minimum, replace the output shaft with a new one.

  1. D026065
    Using a micrometer, measure the thickness of the output shaft flange as shown in the illustration.

    Standard thickness:
    4.8 to 5.2 mm (0.1890 to 0.2047 in.)

    If the thickness is not within the specified values, replace the output shaft.


INSPECT 3RD GEAR

  1. D026066
    Using a cylinder gauge, measure the inner diameter of the 3rd gear.

    Standard diameter:
    44.015 to 44.040 mm (1.7329 to 1.7339 in.)

    Maximum diameter:
    44.040 mm (1.7339 in.)

    If the inner diameter is greater than the maximum, replace the 3rd gear with a new one.


INSPECT 2ND GEAR

  1. D026067
    Using a cylinder gauge, measure the inner diameter of the 2nd gear.

    Standard diameter:
    53.015 to 53.040 mm (2.0872 to 2.0881 in.)

    Maximum diameter:
    53.040 mm (2.0881 in.)

    If the inner diameter is greater than the maximum, replace the 2nd gear with a new one.


INSPECT 1ST GEAR

  1. D026068
    Using a cylinder gauge, measure the inner diameter of the 1st gear.

    Standard diameter:
    46.015 to 46.040 mm (1.812 to 1.813 in.)

    Maximum diameter:
    46.040 mm (1.8126 in.)

    If the inner diameter is greater than the maximum, replace the 1st gear with a new one.


INSPECT 1ST GEAR THRUST WASHER

  1. D026069
    Using a micrometer, measure the thickness of the 1st gear thrust washer.

    Standard thickness:
    5.95 to 6.05 mm (0.2346 to 0.2382 in.)

    Minimum thickness:
    5.96 mm (0.2346 in.)

    If the thickness is less than the minimum, replace the 1st gear thrust washer.


INSPECT SYNCHRONIZER RING NO.1 (for 1st Gear (2TR-FE))

  1. D026072
    Apply gear oil to the cone of the 1st gear, and check that it does not turn in either direction while pushing the synchronizer ring No.1 (for the first synchronizer ring).
    If it turns, replace the synchronizer ring No.1.

  1. D026073
    Measure the clearance between the synchronizer ring No.1 and 1st gear while pushing the synchronizer ring No.1 against the cone of the 1st gear.

    Standard clearance:
    0.75 to 1.65 mm (0.0295 to 0.0649 in.)

    If the clearance is not within the specified values, replace the synchronizer ring No.1 with a new one.


INSPECT SYNCHRONIZER RING SET NO.1 (for 1st Gear (2KD-FTV))

  1. D029123
    Apply gear oil to the cone of the 1st gear, and check that it does not turn in either direction while pushing the synchronizer ring set No.1 (for the first synchronizer ring).
    If it turns, replace the synchronizer ring set No.1.

  1. D029124
    Measure the clearance between the synchronizer ring No.1 and 1st gear while pushing the synchronizer ring No.1 against the cone of the 1st gear.

    Standard clearance:
    0.65 to 1.75 mm (0.0256 to 0.0689 in.)

    If the clearance is not within the specified values, replace the synchronizer ring No.1 with a new one.


INSPECT SYNCHRONIZER RING SET NO.1 (for 2nd Gear)

  1. D029125
    Apply gear oil to the cone of the 2nd gear, and check that it does not turn in either direction while pushing the synchronizer ring set No.1 (for the second synchronizer ring).
    If it turns, replace the synchronizer ring set No.1.

  1. D029126
    Measure the clearance between the synchronizer ring set No.1 (for the second synchronizer ring) and 2nd gear while pushing the synchronizer ring set No.1 against the cone of the 2nd gear.

    Standard clearance:
    0.65 to 1.75 mm (0.0256 to 0.0689 in.)

    If the clearance is not within the specified values, replace the synchronizer ring set No.1 (for the second synchronizer ring) with a new one.


INSPECT SYNCHRONIZER RING NO.2 (for 3rd Gear)

  1. D026074
    Apply gear oil to the cone of the 3rd gear, and check that it does not turn in either direction while pushing the synchronizer ring No.2 (for the third synchronizer ring).
    If it turns, replace the synchronizer ring No.2.

  1. D026075
    Measure the clearance between the synchronizer ring No.2 (for the third synchronizer ring) and 3rd gear while pushing the synchronizer ring No.2 (for the second synchronizer ring) against the cone of the 3rd gear.

    Standard clearance:
    0.75 to 1.65 mm (0.0295 to 0.0650 in.)

    If the clearance is not within the specified values, replace the synchronizer ring No.2 (for the third synchronizer ring) with a new one.


INSPECT REVERSE GEAR

  1. D026076E02
    Using vernier calipers, measure the width of the reverse gear groove and the thickness of the claw part on the gear shift fork No.1, and calculate the clearance.

    Standard clearance (A - B):
    0.15 to 0.41 mm (0.0060 to 0.0161 in.)

    If the clearance is not within the specified values, replace the reverse gear and the shift fork No.1 with new ones.


INSPECT TRANSMISSION CLUTCH HUB NO.1

  1. D026077
    Check that the transmission clutch hub No.1 and reverse gear slide smoothly each other.

  1. Check the tip of the spline gear sleeve of the reverse gear for wear.
    If there are any defects, replace the transmission clutch hub No.1.


INSPECT TRANSMISSION HUB SLEEVE NO.2

  1. D026078E02
    Using vernier calipers, measure the width of the transmission hub No.2 groove and the thickness of the claw of the gear shift fork No.2.

    Standard clearance (A - B):
    0.15 to 0.35 mm (0.0059 to 0.0138 in.)

    If the clearance is not within the specified values, replace the transmission hub sleeve No.2 and the shift fork No.2 with new ones.


INSPECT TRANSMISSION CLUTCH HUB NO.2

  1. D026079
    Check the sliding condition between the transmission clutch hub No.2 and the transmission hub sleeve No.2.

  1. Check the tip of the spline gear sleeve of the reverse gear for wear.

← DISASSEMBLY (from Oct 2014)INSPECTION (from Jan 2017) →