2014-2019 Hiace · Service Manual SERVICE SPECIFICATIONS

SERVICE DATA

Specifications · Vehicles built from Oct 2014

ACCELERATOR PEDAL ROD 
Tester display
Condition
Specified Condition
Accel Sens. No.1 Volt %
Released
10 to 22%
Depressed
52 to 90%
Accel Sens. No.2 Volt %
Released
24 to 40%
Depressed
68 to 95%
CRANKSHAFT POSITION SENSOR 
Tester Connection
Condition
Specified Condition
1 - 2
-10°C (14°F) to 50°C (122°F)
19 to 32 Ω
50°C (122°F) to 100°C (212°F)
24 to 37 Ω
ENGINE COOLANT TEMPERATURE SENSOR 
Tester Connection
Condition
Specified Condition
1 - 2
20°C (68°F)
2.32 to 2.59 kΩ
80°C (176°F)
0.310 to 0.326 kΩ
INTAKE AIR TEMPERATURE SENSOR 
Tester Connection
Condition
Specified Condition
1 - 2
20°C (68°F)
2.21 to 2.69 kΩ
MANIFOLD ABSOLUTE PRESSURE SENSOR 
Tester Connection
Condition
Specified Condition
D57-3 (VC) - D57-1 (E)
Ignition switch ON
4.75 to 5.25 V
D57-2 (PIM) - D57-1 (E)
Ignition switch ON
3.0 to 5.0 V
INTEGRATION RELAY 
Item
Tester Connection
Condition
Specified Condition
No. 1 integration relay (EFI MAIN)
10B-1 - 10B-4
Battery voltage not applied to terminals 10B-2 and 10B-3
10 kΩ or higher
Battery voltage applied to terminals 10B-2 and 10B-3
Below 1 Ω
RELAY 
Item
Tester Connection
Condition
Specified Condition
No. 2 integration relay (HD-LP NO. 1)
d-2 - 12D-3
Battery voltage not applied to terminals d-2 and 12D-4
10 kΩ or higher
Battery voltage applied to terminals d-2 and 12D-4
Below 1 Ω
No. 2 integration relay (DIM NO. 1)
12A-1 - 12C-2
Battery voltage not applied to terminals 12C-3 and 12C-1
10 kΩ or higher
Battery voltage applied to terminals 12C-3 and 12C-1
Below 1 Ω
No. 2 integration relay (HD-LP NO. 2)
c-2 - 12B-9
Battery voltage not applied to terminals c-2 and 12B-10
10 kΩ or higher
Battery voltage applied to terminals c-2 and 12B-10
Below 1 Ω
No. 2 integration relay (DIM NO. 2)
12A-1 - 12B-12
Battery voltage not applied to terminals 12B-8 and 12B-11
10 kΩ or higher
Battery voltage applied to terminals 12B-8 and 12B-11
Below 1 Ω
No. 2 integration relay (IG2)
12A-1 - 12D-1
Battery voltage not applied to terminals 12D-2 and 12E-4
10 kΩ or higher
Battery voltage applied to terminals 12D-2 and 12E-4
Below 1 Ω
No. 2 integration relay (DRL)
12A-1 - 12D-6
Battery voltage not applied to terminals 12E-12 and 12D-7
10 kΩ or higher
Battery voltage applied to terminals 12E-12 and 12D-7
Below 1 Ω
No. 2 integration relay (ACC)
12E-7 - 12E-9
Battery voltage not applied to terminals 12E-8 and 12E-4
10 kΩ or higher
Battery voltage applied to terminals 12E-8 and 12E-4
Below 1 Ω
No. 2 integration relay (100V)
12A-1 - 12E-3
Battery voltage not applied to terminals 12E-1 and 12E-4
10 kΩ or higher
Battery voltage applied to terminals 12E-1 and 12E-4
Below 1 Ω
No. 2 integration relay (FR FOG)
12B-3 - 12B-1
Battery voltage not applied to terminals 12B-6 and 12C-4
10 kΩ or higher
Battery voltage applied to terminals 12B-6 and 12C-4
Below 1 Ω
No. 2 integration relay (DOME CUT)
12C-7 - 12C-6
Battery voltage not applied to terminals 12C-8 and 12C-5
10 kΩ or higher
Battery voltage applied to terminals 12C-8 and 12C-5
Below 1 Ω
VENTURI 
Item
Tester Connection
Condition
Specified Condition
Throttle control motor
2 - 1, 3
20°C (68°F)
18 to 22 Ω
5 - 4, 6
20°C (68°F)
18 to 22 Ω
VENTURI 
Item
Throttle valve
Specified Condition
Throttle valve switch
Fully open
Below 1 Ω
Fully close
10 KΩ or higher
← TORQUE SPECIFICATIONS (from Oct 2014)TORQUE SPECIFICATIONS (from Oct 2014) →