P1601 EEPROM Error - Injector Correction Value, DPF Thermal Degradation Record
Diagnostic trouble codes · Vehicles built Apr 2016 – Dec 2016
Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Nov 2015 Dec 2015 – Mar 2016 Apr 2016 – Dec 2016 from Jan 2017
DESCRIPTION
| DTC Detection Drive Pattern |
DTC Detection Condition |
Trouble Area |
| Ignition switch ON for 1 second |
Any condition is met (1 trip detection logic):
|
|
- NOTICE:
- When an injector assembly is replaced, the new injector compensation code must be input into the ECM. When the ECM is replaced, all of the existing injector compensation codes must be input into the new ECM.
- Injector compensation codes are unique, 30-digit, alphanumeric values printed on the head portion of each injector assembly. If an incorrect injector compensation code is input into the ECM, the engine assembly may rattle or engine idling may become rough. In addition, engine failure may occur and the life of the engine may be shortened.
- When an injector assembly is replaced, perform pilot quantity learning. When the ECM is replaced, all of the existing injector pilot quantity learning values must be input into the new ECM.
- When an injector assembly is replaced, the new injector compensation code must be input into the ECM. When the ECM is replaced, all of the existing injector compensation codes must be input into the new ECM.
- HINT:
- When replacing the ECM with a new one, if the injector compensation code and/or injector pilot quantity learning value are not entered, DTC P1601 will be stored.
| When replacing the ECM with a new one, input all learning values and codes into the new ECM as follows: |
Prior to replacing the ECM, use the GTS to read and save each learning value and code from the original ECM (Click here).
After installing a new ECM, input the saved learning values and codes into the new ECM using the GTS (Click here).
Turn the ignition switch off and turn the GTS off.
Wait for at least 30 seconds.
Turn the ignition switch to ON and turn the GTS on.
Clear DTC P1601 stored in the ECM using the GTS (Click here).
- HINT:
- Each injector assembly has different fuel injection characteristics. In order to optimize the fuel injections, the ECM uses the compensation codes to balance the different fuel injections between each injector assembly.
- When you first turn the ignition switch to ON after replacing the ECM and one or more other components, DTC P1601 is stored. Manually clear the DTC upon completion of compensation code registration.
Replacement Part
Utility Item
ECM
- Learning Values Save (Click here)
- Learning Values Write (Click here)
Injector assembly
- Input Injector Compensation Code (Click here)
- Pilot Quantity Learning (Click here)
- Learning Values Save (Click here)
- Each injector assembly has different fuel injection characteristics. In order to optimize the fuel injections, the ECM uses the compensation codes to balance the different fuel injections between each injector assembly.
INSPECTION PROCEDURE
- NOTICE:
- After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
- HINT:
- Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was running or stopped, if the engine was warmed up or not, and other data from the time the malfunction occurred.
| 1. LEARNING VALUES CONFIRMATION |
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
- NOTICE:
- Do not start the engine.
Enter the following menus: Powertrain / Engine and ECT / Utility / Learning values confirmation (Click here).
Result Result
Proceed to
The injector compensation codes are not input
A
The injector compensation codes registered in the ECM are different than the codes imprinted on the injector assemblies
A
The pilot quantity learning values are set to the default values
B
Except above
C
- HINT:
- When the injector pilot quantity learning values are set to the default values, "7FFF" is displayed.
|
|
||||
|
|
||||
| A | |
| 2. REGISTER INJECTOR COMPENSATION CODE |
Register the injector compensation code (Click here).
|
|
||||
| 3. LEARNING VALUES WRITE |
- HINT:
- When replacing the ECM, after performing "Learning Values Save" to save the learned values from the old ECM using the GTS and replacing the old ECM with a new one, "Learning Values Write" was not performed using the GTS causing this DTC to be output.
Install the old ECM.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Utility / Learning values save (Click here).
Remove the old ECM.
Install a new ECM.
Enter the following menus: Powertrain / Engine and ECT / Utility / Learning values write (Click here).
| NEXT | |
| 4. LEARNING VALUES CONFIRMATION |
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
- NOTICE:
- Do not start the engine.
Enter the following menus: Powertrain / Engine and ECT / Utility / Learning values confirmation (Click here).
Result Result
Proceed to
The pilot quantity learning values are set to the default values
A
Except above
B
- HINT:
- When the injector pilot quantity learning values are set to the default values, "7FFF" is displayed.
|
|
||||
| A | |
| 5. PILOT QUANTITY LEARNING |
Perform the injector pilot quantity learning (Click here).
| NEXT | |
| 6. CHECK DTC OUTPUT |
Connect the GTS to the DLC3.
Clear the DTCs (Click here).
Turn the ignition switch off and leave the vehicle for 30 seconds or more.
Turn the ignition switch to ON for 1 second.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
Result Result
Proceed to
No DTC is output
A
P1601 is output
B
|
|
||||
| A | ||
| ||
| 7. REPLACE ECM |
Replace the ECM (Click here).
| NEXT | |
| 8. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Connect the GTS to the DLC3.
Clear the DTCs (Click here).
Turn the ignition switch off and leave the vehicle for 30 seconds or more.
Turn the ignition switch to ON for 1 second.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Confirm that the DTC is not output again.
| NEXT | ||
| ||
