2014-2019 Hiace · Service Manual RESTRAINTS

B1662/45 Indicator Light Circuit Malfunction

Diagnostic trouble codes · Vehicles built Oct 2014 – Dec 2014

DESCRIPTION

The indicator light circuit consists of the center airbag sensor assembly and combination meter assembly. If the center airbag sensor assembly detects a malfunction in the airbag system, the SRS warning light will come on to inform the driver.
DTC B1662/45 is stored when a malfunction is detected in the indicator light circuit.
DTC No.
Detection Condition
Trouble Area
B1662/45
  1. The center airbag sensor assembly detects a short to ground or B+, or an open in the indicator light circuit.
  2. Combination meter assembly malfunction
  3. Center airbag sensor assembly malfunction
  1. Instrument panel wire
  2. Combination meter assembly
  3. Center airbag sensor assembly

WIRING DIAGRAM

E287495E01

INSPECTION PROCEDURE


1. CHECK CONNECTORS
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Check that the connectors are properly connected to the center airbag sensor assembly and combination meter assembly.

    OK:
    The connectors are properly connected.

    HINT:
    If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.

  1. Disconnect the connectors from the center airbag sensor assembly and combination meter assembly.

  1. Check that the terminals of the connectors are not damaged.

    OK:
    The terminals are not deformed or damaged.



NG
REPAIR OR REPLACE INSTRUMENT PANEL WIRE
OK


2. CHECK INSTRUMENT PANEL WIRE (SHORT TO GROUND)
E287494E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    B4-14 (LA) - Body ground
    Always
    1 MΩ or higher

Text in Illustration 
*1
Combination Meter Assembly
*2
Center Airbag Sensor Assembly
*a
Connector B
*b
Instrument Panel Wire


NG
REPAIR OR REPLACE INSTRUMENT PANEL WIRE
OK


3. CHECK INSTRUMENT PANEL WIRE (OPEN)
E287496E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    B4-14 (LA) - H20-40 (SW)
    Always
    Below 1 Ω

    Text in Illustration 
    *1
    Combination Meter Assembly
    *2
    Center Airbag Sensor Assembly
    *a
    Connector B
    *b
    Connector C
    *c
    Instrument Panel Wire



NG
REPAIR OR REPLACE INSTRUMENT PANEL WIRE
OK


4. CHECK INSTRUMENT PANEL WIRE (SHORT TO B+)
E287494E01
  1. Connect the cable to the negative (-) battery terminal.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    B4-14 (LA) - Body ground
    Ignition switch ON
    Below 1 V

    Text in Illustration 
    *1
    Combination Meter Assembly
    *2
    Center Airbag Sensor Assembly
    *a
    Connector B
    *b
    Instrument Panel Wire



NG
REPAIR OR REPLACE INSTRUMENT PANEL WIRE
OK


5. CHECK CENTER AIRBAG SENSOR ASSEMBLY

  1. E287493E01
    Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Connect the connector to the center airbag sensor assembly.

  1. Connect the cable to the negative (-) battery terminal.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    H20-40 (SW) - Body ground
    For 6 seconds after ignition switch turned ON.
    Below 1 V
    After 6 seconds have passed since ignition switch turned ON.
    11 to 14 V

    Text in Illustration 
    *1
    Combination Meter Assembly
    *2
    Center Airbag Sensor Assembly
    *a
    Connector C
    *b
    Instrument Panel Wire



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY
OK

REPLACE COMBINATION METER ASSEMBLY


← B161A/8A Lost Communication with Front Satellite Sensor Bus (from Jan 2017)B1800/51 Short in Driver Side Squib Circuit (+ B1801/51, B1802/51, B1803/51) (Oct 2014 – Dec 2014) →