2014-2019 Hiace · Service Manual BRAKE

BLEEDING

Removal / installation · Vehicles built from Jan 2017

Versions by build date: Jan 2015 – Dec 2016 from Jan 2017

NOTICE:
  1. As brake fluid may overflow, do not leave the brake fluid can in the reservoir filler opening when adding brake fluid.
  2. Do not allow brake fluid to come into contact with any painted surface. If contact occurs, wash off the fluid immediately.
  3. Perform brake fluid replacement while adding fluid to maintain the fluid level between the MIN and MAX lines of the reservoir.


1. ADD BRAKE FLUID

Brake fluid:
SAE J1703 or FMVSS No. 116 DOT 3 or equivalent

NOTICE:
Do not remove the filter from the brake master cylinder reservoir and be sure to fill with new brake fluid to avoid any potential contamination of the brake system. Contamination, for example by dirt particles or mineral oil, could lead to functional brake problems.


2. BLEED BRAKE LINE
  1. Remove the brake master cylinder reservoir filler cap assembly.

  1. Add brake fluid until the fluid level is between the MIN and MAX lines of the reservoir.

    Brake fluid:
    SAE J1703 or FMVSS No. 116 DOT 3 or equivalent

    NOTICE:
    Do not remove the filter from the brake master cylinder reservoir and be sure to fill with new brake fluid to avoid any potential contamination of the brake system. Contamination, for example by dirt particles or mineral oil, could lead to functional brake problems.

  1. Loosen the bleeder plug of the front disc brake cylinder RH.

  1. Repeatedly depress the brake pedal and bleed the air from the bleeder plug of the front disc brake cylinder RH.

    NOTICE:
    Add fluid as necessary so that the fluid in the reservoir does not decrease below the MIN level.

  1. After air is completely bled out, tighten the bleeder plug while depressing the brake pedal.

    Torque:
    11 N*m{ 110 kgf*cm , 8 ft.*lbf }

  1. Bleed the air from the bleeder plug of the front disc brake cylinder LH using the same procedure as for the RH side.

  1. Loosen the bleeder plug of the rear wheel brake cylinder RH.

  1. Repeatedly depress the brake pedal and bleed the air from the bleeder plug of the rear wheel brake cylinder RH.

    NOTICE:
    Add fluid as necessary so that the fluid in the reservoir does not decrease below the MIN level.

  1. After air is completely bled out, tighten the bleeder plug while depressing the brake pedal.

    Torque:
    11 N*m{ 112 kgf*cm , 8 ft.*lbf }

  1. Bleed the air from the bleeder plug of the rear wheel brake cylinder LH using the same procedure as for the RH side.

  1. Check for brake fluid leaks.

  1. Check the brake fluid level and add fluid if necessary.

    Brake fluid:
    SAE J1703 or FMVSS No. 116 DOT 3 or equivalent

    NOTICE:
    Do not remove the filter from the brake master cylinder reservoir and be sure to fill with new brake fluid to avoid any potential contamination of the brake system. Contamination, for example by dirt particles or mineral oil, could lead to functional brake problems.


3. BLEED BRAKE SYSTEM

CAUTION:
If air is bled without using the GTS, damage or accidents may result. Therefore, always use the GTS when bleeding air.

  1. Remove the brake master cylinder reservoir filler cap assembly.

  1. Add brake fluid until the fluid level is between the MIN and MAX lines of the reservoir.

    Brake fluid:
    SAE J1703 or FMVSS No. 116 DOT 3 or equivalent

    NOTICE:
    Do not remove the filter from the brake master cylinder reservoir and be sure to fill with new brake fluid to avoid any potential contamination of the brake system. Contamination, for example by dirt particles or mineral oil, could lead to functional brake problems.

  1. C106089
    Using a union nut wrench, disconnect the 2 brake tubes from the master cylinder.

    NOTICE:
    1. Do not kink or damage the brake lines.
    2. Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.

  1. Slowly depress and hold the brake pedal.

  1. C106090
    Block the tube holes with your fingers, and then release the brake pedal.

  1. Remove your fingers, slowly depress and hold the brake pedal, block the tube holes with your fingers again, and then release the brake pedal. Repeat this step 3 or 4 times.

  1. A329093E01
    Using a union nut wrench, connect the 2 brake tubes to the brake master cylinder assembly.

    Torque:
    Specified tightening torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }

    Text in Illustration 
    *a
    Torque Wrench Fulcrum Length

    HINT:
    1. Calculate the torque wrench reading when changing the fulcrum length of the torque wrench (Click here).
    2. When using a union nut wrench (fulcrum length of 20 mm (0.8661 in.)) + torque wrench (fulcrum length of 180 mm (7.0866 in.)): 23 N*m (229 kgf*cm, 17 ft.*lbf)

  1. Loosen the bleeder plug of the front brake cylinder RH.

  1. Repeatedly depress the brake pedal and bleed the air from the bleeder plug of the front brake cylinder RH.

    NOTICE:
    Add fluid as necessary so that the fluid in the reservoir does not decrease below the MIN level.

  1. After air is completely bled out, tighten the bleeder plug while depressing the brake pedal.

    Torque:
    11 N*m{ 110 kgf*cm , 8 ft.*lbf }

  1. Bleed the air from the bleeder plug of the front disc brake cylinder LH using the same procedure as for the RH side.

  1. Loosen the bleeder plug of the rear wheel brake cylinder RH.

  1. Repeatedly depress the brake pedal and bleed the air from the bleeder plug of the rear brake cylinder RH.

    NOTICE:
    Add fluid as necessary so that the fluid in the reservoir does not decrease below the MIN level.

  1. After the air is completely bled out, tighten the bleeder plug while depressing the brake pedal.

    Torque:
    11 N*m{ 112 kgf*cm , 8 ft.*lbf }

  1. Bleed the air from the bleeder plug of the rear wheel brake cylinder LH using the same procedure as for the RH side.

  1. Depress the brake pedal more than 20 times with the ignition switch off.

  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

    NOTICE:
    Do not start the engine.

  1. Enter the following menus: Chassis / ABS/VSC/TRC / Utility / Air Bleeding.

  1. Bleed the brake system following the instructions on the GTS.

  1. After air bleeding, tighten each bleeding plug.

    Torque:
    Front bleeder plug:
    11 N*m{ 110 kgf*cm , 8 ft.*lbf }
    Rear bleeder plug:
    11 N*m{ 112 kgf*cm , 8 ft.*lbf }

  1. Turn the GTS off and turn the ignition switch off.

  1. Disconnect the GTS from the DLC3.

  1. Check for brake fluid leaks.

  1. Check the brake fluid level and add fluid if necessary.

    Brake fluid:
    SAE J1703 or FMVSS No. 116 DOT 3 or equivalent

    NOTICE:
    Do not remove the filter from the brake master cylinder reservoir and be sure to fill with new brake fluid to avoid any potential contamination of the brake system. Contamination, for example by dirt particles or mineral oil, could lead to functional brake problems.

← BLEEDING (Jan 2015 – Dec 2016)BLEEDING (Oct 2014 – Dec 2014) →