2014-2019 Hiace · Service Manual ENGINE

REASSEMBLY

Removal / installation · Vehicles built from Oct 2014


1. INSPECT LOCK PLATE FOR DAMAGE

  1. A099690E02
    Inspect the lock plate for damage.
    If the sides of the lock plate groove are deformed, reassembly of the tank will be impossible. Correct any deformations with pliers.
    Water will leak if the bottom of the lock plate groove is damaged or dented. Repair or replace it as necessary.

    NOTICE:
    The radiator can only be recaulked twice. After the second time, the radiator core must be replaced.


2. INSTALL RADIATOR TANK UPPER AND TANK LOWER

  1. A113341E01
    Check that there are no foreign objects in the lock plate groove, and install a new O-ring. Make sure the O-ring is not twisted.

    HINT:
    When cleaning the lock plate groove, lightly rub it with sandpaper without scratching it.

  1. Install the tank without damaging the O-ring.

  1. A234650E01
    Lightly tap the lock plate with a plastic-faced hammer so that there is no gap between the lock plate and the tank.


3. ASSEMBLE SST

  1. A234961E01
    Install the punch assembly to part A of the overhaul handle as shown in the illustration.
    SST
    09230-01010   (09231-01010, 09231-01020)
    09231-14010  

  1. While squeezing the handle, adjust the stopper bolt so that dimension B is as specified below.

    Dimension B:
    8.4 mm (0.331 in.)


4. CAULK LOCK PLATE

  1. A234651E01
    Lightly press SST against the lock plate in the order shown in the illustration. After repeating this a few times, fully caulk the lock plate by squeezing the handle until stopped by the stopper bolt.
    SST
    09230-01010   (09231-01010, 09231-01020)
    09231-14010  

    NOTICE:

    1. A234652
      Do not press the protruding areas around the ports.

    2. A234653
      Do not use SST to press the areas indicated by the circle marks in the illustration. Use pliers and be careful not to damage the core plates.

  1. A234654E01
    Check the lock plate height H after completing the caulking.

    Standard plate height H:
    8.45 mm (0.333 in.)

    If the height is not as specified, readjust the stopper bolt of the handle and caulk the lock plate again.


5. INSTALL NO. 2 RADIATOR LOWER TANK PIPE

  1. A234647
    Connect the No. 2 radiator lower tank pipe.

  1. Install the No. 2 radiator lower tank pipe with the bolt.

    Torque:
    6.0 N*m{ 61 kgf*cm , 53 in.*lbf }


6. INSTALL NO. 1 RADIATOR LOWER TANK PIPE

  1. A234646
    Install a new O-ring to the No. 1 radiator lower tank pipe.

  1. Install the No. 1 radiator lower tank pipe with the 3 bolts.

    Torque:
    6.0 N*m{ 61 kgf*cm , 53 in.*lbf }


7. INSTALL RADIATOR UPPER TANK PIPE

  1. A234643
    Install a new O-ring to the radiator upper tank pipe.

  1. Install the radiator upper tank pipe with the 3 bolts.

    Torque:
    6.0 N*m{ 61 kgf*cm , 53 in.*lbf }


8. INSTALL RADIATOR DRAIN COCK PLUG
  1. Install a new O-ring to the drain cock plug.

  1. Install the drain cock plug.

← DISASSEMBLY (from Oct 2014)INSTALLATION (Oct 2014 – Dec 2014) →