2014-2019 Hiace · Service Manual BRAKE

TERMINALS OF ECU

System information · Vehicles built Jan 2015 – Nov 2017

Versions by build date: Jan 2015 – Nov 2017 from Dec 2017


TERMINALS OF ECU
C306841E01
Text in Illustration 
*a
Component without harness connected
(Skid Control ECU (Brake Actuator Assembly))
-
-
Terminal No. (Symbol)
Terminal Description
1 (GND2)
Pump motor ground
2
- (Not used)
3 (PKB)
Parking brake switch assembly input
4
- (Not used)
5
- (Not used)
6
- (Not used)
7
- (Not used)
8
- (Not used)
9
- (Not used)
10 (CANL)
CAN communication line L
11 (EXI3)
Back-up light switch assembly input*1
Park/neutral position switch assembly input*2
12 (IG1)
ECU power supply input
13 (+BM)
Motor relay power supply
14 (SP1)
Speed signal output for speedometer
15 (RR-)
Rear wheel speed RH (-) signal input
16 (RR+)
Rear wheel speed RH (+) power supply output
17 (FL-)
Front wheel speed LH (-) signal input
18 (FL+)
Front wheel speed LH (+) power supply output
19
- (Not used)
20
- (Not used)
21
- (Not used)
22 (CANH)
CAN communication line H
23
- (Not used)
24 (TS)
Sensor check input
25 (GND1)
Skid control ECU (Brake actuator assembly) ground
26
- (Not used)
27
- (Not used)
28 (RL-)
Rear wheel speed LH (-) signal input
29 (RL+)
Rear wheel speed LH (+) power supply output
30 (FR-)
Front wheel speed RH (-) signal input
31 (FR+)
Front wheel speed RH (+) power supply output
32
- (Not used)
33 (CSW)
VSC OFF switch input
34
- (Not used)
35 (STP)
Stop light switch assembly input
36
- (Not used)
37
- (Not used)
38 (+BS)
Solenoid relay power supply
  1. *1: for Manual Transmission
  2. *2: for Automatic Transmission

TERMINAL INSPECTION

  1. Disconnect the B92 connector and measure the voltage or resistance on the wire harness side.
    C306842E02

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid Control ECU (Brake Actuator Assembly))
    -
    -

    HINT:
    Voltage cannot be measured with the connector connected to the skid control (brake actuator assembly) as the connector is watertight.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    B92-1 (GND2) - Body ground
    W-B - Body ground
    Pump motor ground
    Always
    Below 1 Ω
    B92-3 (PKB) - Body ground
    B- Body ground
    Parking brake switch assembly input
    Parking brake lever pulled → released
    Below 1 Ω → 10 kΩ or higher
    B92-11 (EXI3) - Body ground
    L - Body ground
    Back-up light switch assembly input*1
    Park/neutral position switch assembly input*2
    Shift lever not in R → Shift lever in R
    Below 1 V → 11 to 14 V
    B92-12 (IG1) - Body ground
    B - Body ground
    ECU power supply input
    Ignition switch ON
    11 to 14 V
    B92-13 (+BM) - Body ground
    W - Body ground
    Motor relay power supply
    Always
    11 to 14 V
    B92-14 (SP1) - Body ground
    P - Body ground
    Speed signal output for speedometer
    Ignition switch ON
    11 to 14 V
    B92-25 (GND1) - Body ground
    W-B - Body ground
    Skid control ECU (Brake actuator assembly) ground
    Always
    Below 1 Ω
    B92-33 (CSW) - Body ground
    G - Body ground
    VSC OFF switch input
    VSC OFF switch pressed and held → released
    Below 1 Ω → 10 kΩ or higher
    B92-35 (STP) - Body ground
    L - Body ground
    Stop light switch assembly input
    Stop light switch assembly on → off (Brake pedal depressed → released)
    8 to 14 V → Below 1.5 V
    B92-38 (+BS) - Body ground
    W-R - Body ground
    Solenoid relay power supply
    Always
    11 to 14 V
    *1: for Manual Transmission
    *2: for Automatic Transmission

← PROBLEM SYMPTOMS TABLE (from Dec 2017)TERMINALS OF ECU (from Dec 2017) →