SERVICE DATA
Specifications · Vehicles built Oct 2014 – Dec 2014
| Line pressure (Fluid temperature): 50 to 80°C (122 to 176°F) AT stall (Throttle valve fully opened) |
D position |
1030 to 1196 kPa (10.6 to 12.1 kgf/cm2, 150 to 173 psi) |
| R position |
1422 to 1785 kPa (14.6 to 18.2 kgf/cm2, 207 to 258 psi) |
|
| Engine stall speed |
D positions |
1950 to 2250 rpm |
| Time lag |
N → D position N → R position |
Less than 1.2 seconds Less than 1.5 seconds |
| Drive plate runout |
Maximum. |
0.30 mm (0.0118 in.) |
| Shift schedule | ||
| D position (Throttle valve fully opened) |
1 → 2 |
46 to 54 km/h (29 to 33 mph) |
| 2 → 3 |
93 to 100 km/h (58 to 62 mph) |
|
| 3 → 4 |
125 to 135 km/h (78 to 83 mph) |
|
| 4 → 3 |
116 to 124 km/h (73 to 77 mph) |
|
| 3 → 2 |
84 to 89 km/h (53 to 55 mph) |
|
| 2 → 1 |
39 to 43 km/h (25 to 26 mph) |
|
| D position (Throttle valve fully closed) |
3 → 4 |
36 to 42 km/h (23 to 26 mph) |
| 4 → 3 |
28 to 32 km/h (18 to 19 mph) |
|
| 3 position (Throttle valve fully opened) |
1 → 2 |
46 to 54 km/h (29 to 33 mph) |
| 2 → 3 |
93 to 100 km/h (58 to 62 mph) |
|
| 4 → 3 |
116 to 124 km/h (73 to 77 mph) |
|
| 3 → 2 |
84 to 89 km/h (53 to 55 mph) |
|
| 2 → 1 |
39 to 43 km/h (25 to 26 mph) |
|
| 2 position (Throttle valve fully opened) |
1 → 2 |
46 to 54 km/h (29 to 33 mph) |
| 3 → 2 |
88 to 92 km/h (55 to 57 mph) |
|
| 2 → 1 |
39 to 43 km/h (25 to 26 mph) |
|
| L position (Throttle valve fully opened) |
3 → 2 |
88 to 92 km/h (55 to 57 mph) |
| 2 → 1 |
43 to 47 km/h (27 to 29 mph) |
|
| Lock-up point (Throttle valve opening 5 %) | ||
| D position (4th gear) |
Lock-up ON |
62 to 66 km/h (39 to 41 mph) |
| Lock-up OFF |
57 to 61 km/h (36 to 37 mph) |
|
| 3 position (3th gear) |
Lock-up ON |
46 to 50 km/h (29 to 31 mph) |
| Lock-up OFF |
41 to 45 km/h (26 to 27 mph) |
|
| Body clearance |
Standard |
0.07 to 0.15 mm (0.00276 to 0.00590 in.) |
| Maximum |
0.3 mm (0.0118 in.) |
|
| Tip clearance |
Standard |
0.11 to 0.14 mm (0.00433 to 0.00551 in.) |
| Maximum |
0.3 mm (0.0118 in.) |
|
| Side clearance |
Standard |
0.02 to 0.05 mm (0.000788 to 0.00196 in.) |
| Maximum |
0.1 mm (0.00394 in.) |
|
| Oil pump body bushing inside diameter |
Standard |
38.19 mm (1.50 in.) |
| Drive and driven gear thickness |
Mark. 1 |
17.235 to 17.244 mm (0.6786 to 0.6788 in.) |
| Mark. 2 |
17.245 to 17.254 mm (0.6790 to 0.6792 in.) |
|
| Mark. 3 |
17.255 to 17.265 mm (0.6794 to 0.6797 in.) |
|
| Mark. 4 |
17.266 to 17.275 mm (0.6798 to 0.6801 in.) |
|
| Mark. 5 |
17.276 to 17.285 mm (0.6802 to 0.6805 in.) |
|
| Stator shaft bush inside inside diameter |
Maximum |
23.11 mm (0.910 in.) |
| Extension housing bush inside diameter |
Maximum |
38.09 mm (1.50 in.) |
| Piston stroke |
Standard |
1.74 to 2.44 mm (0.0686 to 0.0960 in.) |
| Clutch drum inside diameter |
Maximum |
23.14 mm (0.911 in.) |
| Planetary gear bush inside diameter |
Maximum |
11.27 mm (0.444 in.) |
| pinion gear thrust clearance |
Standard |
0.20 to 0.50 mm(0.00788 to 0.0196 in.) |
| Pack clearance |
Standard |
0.75 to 1.25 mm (0.0296 to 0.0492 in.) |
| Plate thickness |
1.95 to 2.05 mm (0.0768 to 0.0807 in.) |
|
| 2.25 to 2.35 mm (0.0886 to 0.0925 in.) | ||
| Piston stroke |
Standard |
1.40 to 1.60 mm (0.0552 to 0.0629 in.) |
| Front clutch flange thickness |
1.75 to 1.85 mm (0.0689 to 0.0728 in.) |
|
| 1.95 to 2.05 mm (0.0768 to 0.0807 in.) | ||
| Piston stroke |
Standard |
0.90 to 1.30 mm (0.0355 to 0.0511 in.) |
| Rear clutch flange thickness |
3.475 to 3.600 mm (0.137 to 0.141 in.) |
|
| 3.675 to 3.800 mm (0.145 to 0.149 in.) | ||
| 3.925 to 4.050 mm (0.155 to 0.159 in.) | ||
| Piston stroke |
Standard |
0.75 to 1.35 mm (0.0296 to 0.0531 in.) |
| Center support bush inside diameter |
Maximum |
36.41 mm (1.43 in.) |
| Piston stroke |
Standard |
0.98 to 1.71 mm (0.0386 to 0.0673 in.) |
| Sun gear bush inside diameter |
Maximum |
21.53 mm (0.848 in.) |
| Planetary pinion gear thrust clearance. |
Standard |
0.20 to 0.50 mm(0.00788 to 0.0196 in.) |
| Output shaft bush inside diameter |
Maximum |
18.03 mm (0.710 in.) |
| Output shaft end play |
Standard end paly |
0.3 to 0.9 (0.0118 to 0.0354 in.) |
| Planetary pinion gear thrust clearance |
Standard |
0.20 to 0.50 mm(0.00788 to 0.0196 in.) |
| Pack clearance |
Standard |
0.52 to 1.27 mm (0.0205 to 0.0499 in.) |
| Flange thickness |
Mark - |
2.95 to 3.05 mm (0.117 to 0.120 in.) |
| Mark 325 |
3.20 to 3.30 mm (0.126 to 0.129 in.) |
|
| Mark 350 |
3.45 to 3.55 mm (0.136 to 0.139 in.) |
|
| Mark 375 |
3.70 to 3.80 mm (0.146 to 0.149 in.) |
|
| Mark 400 |
3.95 to 4.05 mm (0.156 to 0.159 in.) |
|
| Mark 425 |
4.20 to 4.30 mm (0.165 to 0.169 in.) |
| Transmission case bush |
Maximum |
38.19 mm (1.50 in.) |
| C-1 |
Free length |
75.03 mm (2.95 in.) |
| Outer diameter |
17.00 mm (0.669 in.) |
|
| Color |
White or Blue |
|
| C-2 |
Free length |
62.27 mm (2.45 in.) |
| Outer diameter |
16.4 mm (0.646 in.) |
|
| Color |
White or Purple |
|
| B-2 |
Free length |
56.4 mm (2.22 in.) |
| Outer diameter |
18.79 mm (0.740 in.) |
|
| Color |
Green |