2014-2019 Hiace · Service Manual SERVICE SPECIFICATIONS

SERVICE DATA

Specifications · Vehicles built Jan 2015 – Dec 2016

Versions by build date: Jan 2015 – Dec 2016 from Jan 2017

Line pressure (Fluid temperature): 50 to 80°C (122 to 176°F)
At stall speed (Throttle valve fully open)
D position
1450 to 1740 kPa (14.8 to 17.7 kgf/cm2, 211 to 252 psi)
R position
1550 to 1840 kPa (15.9 to 18.7 kgf/cm2, 225 to 267 psi)
Engine stall speed
D position
2020 +- 200 rpm
Time lag
N → D position
Less than 1.2 seconds
N → R position
Less than 1.5 seconds
Drive plate runout
Maximum
0.30 mm (0.0118 in.)
Shift schedule
D, 6 position

for 1TR-FE:
Throttle valve fully open
1 → 2
25 to 35 km/h (16 to 21 mph)
2 → 3
60 to 70 km/h (38 to 43 mph)
3 → 4
85 to 95 km/h (53 to 59 mph)
4 → 5
130 to 140 km/h (81 to 86 mph)
5 → 6
235 to 250 km/h (147 to 155 mph)
for 2TR-FE:
Throttle valve fully open
1 → 2
25 to 35 km/h (16 to 21 mph)
2 → 3
60 to 65 km/h (38 to 40 mph)
3 → 4
85 to 100 km/h (53 to 62 mph)
4 → 5
130 to 145 km/h (81 to 90 mph)
5 → 6
250 to 265 km/h (156 to 164 mph)
for 1TR-FE:
Throttle valve opening 6 %
1 → 2
5 to 10 km/h (4 to 6 mph)
2 → 3
15 to 25 km/h (10 to 15 mph)
3 → 4
25 to 30 km/h (16 to 18 mph)
4 → 5
35 to 45 km/h (22 to 27 mph)
5 → 6
55 to 65 km/h (35 to 40 mph)
for 2TR-FE:
Throttle valve opening 6 %
1 → 2
5 to 15 km/h (4 to 9 mph)
2 → 3
15 to 20 km/h (11 to 12 mph)
3 → 4
25 to 35 km/h (16 to 21 mph)
4 → 5
35 to 45 km/h (22 to 27 mph)
5 → 6
60 to 70 km/h (38 to 43 mph)
Manual downshift speed
for 1TR-FE:
5, 4, 3, 2, 1 gear range
→ 5
190 to 205 km/h (119 to 127 mph)
→ 4
130 to 145 km/h (81 to 90 mph)
→ 3
85 to 100 km/h (53 to 62 mph)
→ 2
55 to 65 km/h (35 to 40 mph)
→ 1
25 to 35 km/h (16 to 21 mph)
for 2TR-FE:
5, 4, 3, 2, 1 gear range
→ 5
185 to 200 km/h (115 to 124 mph)
→ 4
125 to 140 km/h (78 to 86 mph)
→ 3
85 to 95 km/h (53 to 59 mph)
→ 2
55 to 65 km/h (35 to 40 mph)
→ 1
25 to 35 km/h (16 to 21 mph)

NOTICE:
  1. All shift point values indicated in the above tables are actual values. Therefore, if checking a shift point with a chassis dynamometer, keep in mind that there is a range of error in the chassis dynamometer indication.
  2. If checking a shift point against the speed indicated on the speedometer, remember to consider the speedometer correction rate and range of error in the tester indication.

Speed Sensor (Transmission Revolution Sensor) 
Item
Tester connection
Condition
Specified Condition
Transmission revolution sensor NT
1 (NTO) - 2 (NTB)
Low signal
4 to 8 mA
High signal
12 to 16 mA
Transmission revolution sensor SP2
1 (SP2O) - 2 (SP2B)
Low signal
4 to 8 mA
High signal
12 to 16 mA
Transmission Wire 
Tester connection
Condition
Specified Condition
3 (OT+) - 4 (OT-)
5 (OT2+) - 6 (OT2-)
Always
79 Ω to 156 kΩ
3 (OT+) - Body ground
5 (OT2+) - Body ground
Always
10 kΩ or higher
4 (OT-) - Body ground
6 (OT2-) - Body ground
Always
10 kΩ or higher
ATF Temperature
Specified Condition
10°C (50°F)
5 to 8 kΩ
25°C (77°F)
2.5 to 4.5 kΩ
110°C (230°F)
0.22 to 0.28 kΩ
Park/Neutral Position Switch Assembly 
Tester connection
Condition
Specified Condition
4 (B) - 5 (L)
Shift lever in P or N
Below 1 Ω
2 (RB) - 6 (PL)
Shift lever in P
Below 1 Ω
2 (RB) - 1 (RL)
Shift lever in R
Below 1 Ω
2 (RB) - 9 (NL)
Shift lever in N
Below 1 Ω
2 (RB) - 7 (DL)
Shift lever in D, S, "+" or "-"
Below 1 Ω
4 (B) - 5 (L)
Shift lever not in P or N
10 kΩ or higher
2 (RB) - 6 (PL)
Shift lever not in P
10 kΩ or higher
2 (RB) - 1 (RL)
Shift lever not in R
10 kΩ or higher
2 (RB) - 9 (NL)
Shift lever not in N
10 kΩ or higher
2 (RB) - 7 (DL)
Shift lever not in D, S, "+" or "-"
10 kΩ or higher
Valve Body Assembly 
Item
Tester connection
Condition
Specified Condition
Shift solenoid valve SL1, SL3, SL4, SLU and SLT
1 - 2
20°C (68°F)
5.0 to 5.6 Ω
Shift solenoid valve SL
Shift solenoid valve connector terminal - Shift solenoid valve body
20°C (68°F)
11 to 15 Ω
Shift Lock Control ECU 
Tester connection
Condition
Specified Condition
5 (KLS+) - 1 (E)
Ignition switch ACC and shift lever in P
Below 1 V
Ignition switch ACC and shift lever not in P
11 to 14 V
6 (ACC) - 1 (E)
Ignition switch ACC
11 to 14 V
Ignition switch off
Below 1 V
4 (STP) - 1 (E)
Brake pedal depressed
11 to 14 V
Brake pedal released
Below 1 V
8 (IG) - 1 (E)
Ignition switch ON
11 to 14 V
Ignition switch off
Below 1 V
10 (SLS-) - 1 (E)
Ignition switch ON, brake pedal depressed and shift lever in P
Below 2.5 V
Ignition switch ON, brake pedal released and shift lever in P
11 to 14 V
1 (E) - Body ground
Always
Below 1 V
Shift Lock Solenoid 
Tester connection
Condition
Specified Condition
4 (P) - 3 (E2)
Shift lever in P
10 kΩ or higher
Shift lever not in P
Below 1 Ω
1 (SLS+) - 2 (SLS-)
Shift lever held in "+" (Up shift)
112 Ω
Transmission Control Switch 
Tester connection
Condition
Specified Condition
5 (SFTU) - 11 (E))
Shift lever held in "+"
(Up-shift)
Below 1 Ω
4 (SFTD) - 11 (E)
Shift lever held in "-"
(Down-shift)
Below 1 Ω
6 (IG) - 13 (S)
Shift lever in S, "+" or "- "
Below 1 Ω
5 (SFTU) - 11 (E)
Shift lever not held in "+"
10 kΩ or higher
4 (SFTD) - 11 (E)
Shift lever not held in "- "
10 kΩ or higher
6 (IG) - 13 (S)
Shift lever not in S, "+" or "-"
10 kΩ or higher
Automatic Transmission Unit 
Direct clutch drum sub-assembly
Standard inside diameter
59.515 to 59.540 mm (2.3431 to 2.3440 in.)
Input shaft sub-assembly
Standard inside diameter
20.000 to 20.025 mm (0.7874 to 0.7883 in.)
Forward clutch hub sub-assembly
Standard inside diameter
26.037 to 26.062 mm (1.02508 to 1.02606 in.)
Sun gear input drum sub-assembly
Standard inside diameter
35.811 to 35.835 mm (1.4099 to 1.4108 in.)
Front planetary gear assembly
Standard inside diameter
35.811 to 35.835 mm (1.4099 to 1.4108 in.)
Front planetary ring gear flange sub-assembly
Standard inside diameter
54.038 to 54.063 mm (2.1275 to 2.1284 in.)
Rear planetary ring gear flange sub-assembly
Standard inside diameter
32.176 to 32.201 mm (1.2668 to 1.2677 in.)
Center planetary gear assembly
Standard clearance
0.12 to 0.68 mm (0.00473 to 0.0267 in.)
Rear planetary gear assembly
Standard clearance
(Rear planetary gear pinion thrust clearance)
0.2 to 0.6 mm (0.00788 to 0.0236 in.)
Standard inside diameter
(Rear planetary gear bushing)
20.000 to 20.025 mm (0.7874 to 0.7883 in.)
Intermediate shaft
Standard runout
0.03 mm (0.00118 in.)
Standard diameter
A: 32.062 to 32.075 mm (1.2623 to 1.2627 in.)
B: 25.962 to 25.975 mm (1.0222 to 1.0226 in.)
C: 19.963 to 19.976 mm (0.78595 to 0.78645 in.)
Forward clutch return spring sub-assembly
Standard free length
26.74 mm (1.053 in.)
direct clutch return spring sub-assembly
Standard free length
22.14 mm (0.872 in.)
No. 1 brake piston return spring sub-assembly
Standard free length
16.72 mm (0.658 in.)
No. 2 brake piston return spring sub-assembly
Standard free length
16.68 mm (0.657 in.)
1st and reverse brake return spring subassembly
Standard free length
23.74 mm (0.935 in.)
Pack clearance of No. 1 clutch (Forward clutch)
Standard clearance
0.75 to 1.05 mm (0.0295 to 0.0413 in.)
Forward clutch flange thickness
Part No.
35635-71010
3.0 mm (0.118 in.)
Part No.
35635-71020
3.1 mm (0.122 in.)
Part No.
35635-71030
3.2 mm (0.126 in.)
Part No.
35635-71040
3.3 mm (0.130 in.)
Part No.
35635-71050
3.4 mm (0.134 in.)
Part No.
35635-71060
3.5 mm (0.138 in.)
Part No.
35635-71070
3.6 mm (0.142 in.)
Part No.
35635-71080
3.7 mm (0.146 in.)
Part No.
35635-71090
3.8 mm (0.150 in.)
Part No.
35635-71100
3.9 mm (0.154 in.)
Part No.
35635-71110
4.0 mm (0.157 in.)
Part No.
35635-71120
4.1 mm (0.161 in.)
Part No.
35635-71130
4.2 mm (0.165 in.)
Pack clearance of No. 2 clutch (Direct clutch)
Standard clearance
0.4 to 0.7 mm (0.0157 to 0.0275 in.)
Direct clutch flange thickness
Part No.
35675-71010
3.0 mm (0.118 in.)
Part No.
35675-71020
3.1 mm (0.122 in.)
Part No.
35675-71030
3.2 mm (0.126 in.)
Part No.
35675-71040
3.3 mm (0.130 in.)
Part No.
35675-71050
3.4 mm (0.134 in.)
Part No.
35675-71060
3.5 mm (0.138 in.)
Part No.
35675-71070
3.6 mm (0.142 in.)
Part No.
35675-71080
3.7 mm (0.146 in.)
Part No.
35675-71090
3.8 mm (0.150 in.)
Pack clearance of No. 1 brake
Standard clearance
0.3 to 0.6 mm (0.0119 to 0.0236 in.)
No. 1 brake flange thickness
Mark
0
4.9 mm (0.193 in.)
Mark
1
5.0 mm (0.197 in.)
Mark
2
5.1 mm (0.201 in.)
Mark
3
5.2 mm (0.205 in.)
Mark
4
5.3 mm (0.209 in.)
Mark
5
5.4 mm (0.213 in.)
Mark
6
5.5 mm (0.217 in.)
Mark
7
5.6 mm (0.220 in.)
Mark
8
5.7 mm (0.224 in.)
Mark
A
5.8 mm (0.228 in.)
Pack clearance of No. 2 brake
Standard clearance
0.4 to 0.7 mm (0.0158 to 0.0275 in.)
No. 2 brake flange thickness
Mark
0
2.0 mm (0.0787 in.)
Mark
1
2.1 mm (0.0827 in.)
Mark
2
2.2 mm (0.0866 in.)
Mark
3
2.3 mm (0.0906 in.)
Mark
4
2.4 mm (0.0945 in.)
Mark
5
2.5 mm (0.0984 in.)
Mark
6
2.6 mm (0.102 in.)
Mark
7
2.7 mm (0.106 in.)
Mark
8
2.8 mm (0.110 in.)
Pack clearance of No. 4 brake
Standard clearance
0.5 to 0.8 mm (0.0197 to 0.0314 in.)
No. 4 brake flange thickness
Mark
0
1.80 mm (0.0709 in.)
Mark
1
1.97 mm (0.0776 in.)
Mark
3
2.11 mm (0.0831 in.)
Mark
4
2.25 mm (0.0886 in.)
Mark
5
2.39 mm (0.0941 in.)
Mark
7
2.53 mm (0.0996 in.)
Mark
8
2.67 mm (0.105 in.)
Mark
10
2.81 mm (0.111 in.)
Mark
11
2.95 mm (0.116 in.)
Mark
12
3.09 mm (0.122 in.)
Mark
14
3.23 mm (0.127 in.)
Output shaft thrust clearance
(rear planetary gear assembly)
Standard clearance
0.02 to 0.12 mm (0.000787 to 0.00472 in.)
Output shaft thrust bearing race thickness
Part No.
35789-35060
3.80 mm (0.150 in.)
Part No.
35789-50070
3.85 mm (0.152 in.)
Part No.
35789-35070
3.90 mm (0.154 in.)
Part No.
35789-50080
3.95 mm (0.156 in.)
Part No.
35789-35080
4.00 mm (0.157 in.)
Part No.
35789-50090
4.05 mm (0.159 in.)
Part No.
35789-35090
4.10 mm (0.161 in.)
Part No.
35789-50100
4.15 mm (0.163 in.)
Part No.
35789-35100
4.20 mm (0.165 in.)
Part No.
35789-50110
4.25 mm (0.167 in.)
Part No.
35789-50120
4.30 mm (0.169 in.)
Part No.
35789-50130
4.35 mm (0.171 in.)
Oil Pump 
Front oil pump body sub-assembly
Maximum inside diameter
38.138 mm (1.50 in.)
Stator shaft assembly
Maximum inside diameter
22.227 mm (0.875 in.)
Oil pump assembly
Standard body clearance
0.10 to 0.17 mm (0.00394 to 0.00669 in.)
Standard tip clearance
0.07 to 0.15 mm (0.00276 to 0.00590 in.)
Standard side clearance
0.03 to 0.05 mm (0.00118 to 0.00196 in.)
Front oil pump oil seal
Standard Depth
-0.3 to 0.3 mm (-0.0118 to 0.0118 in.)
← TORQUE SPECIFICATIONS (from Dec 2017)SERVICE DATA (from Jan 2017) →