2014-2019 Hiace · Service Manual STEERING

TERMINALS OF ECU

System information · Vehicles built from Oct 2014


TERMINAL INSPECTION
C195844E05
  1. Disconnect the H80 steering lock ECU (steering lock actuator assembly) connector.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Input/Output
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    Related Data List Item
    H80-1 (GND) - Body ground
    -
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    -
    H80-6 (IG2) - H80-1 (GND)
    Input
    B - W-B
    Power source mode signal (IG2 power supply input for entire steering lock actuator assembly)
    Engine switch off → engine switch on (IG)
    Below 1 V → 11 to 14 V
    Entry&Start
    1. Ignition Switch
    H80-7 (B) - Body ground
    Input
    W - Body ground
    Power source
    Always
    11 to 14 V
    -

  3. Reconnect the H80 steering lock ECU (steering lock actuator assembly) connector.

  4. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Input/Output
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    Related Data List Item
    H80-4 (SLP1) - H80-1 (GND)
    Output
    LG - W-B
    Steering lock bar position signal (output signal from steering unlock sensor)
    Steering locked → unlocked
    11 to 14 V → Below 1.5 V
    Entry&Start
    1. Sensor Value
    H80-5 (LIN) - H80-1 (GND)
    Input/Output
    SB - W-B
    LIN communication line
    -
    -
    Entry&Start
    1. Steering Lock Start Cond

  5. Check the signal waveform according to the condition(s) in the table below.

    Terminal No. (Symbol)
    Input/Output
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    Related Data List Item
    H80-3 (IGE) - H80-1 (GND)
    Input
    V - W-B
    Steering lock motor activation command signal (motor activation command signal sent from certification ECU (smart key ECU assembly))
    Any door opened when conditions below met, and then steering lock motor activated:
    1. Shift lever in P
    2. Steering lock unlocked in advance by carrying key and turning engine switch on (IG)
    3. After above conditions met, engine switch turned off
    Pulse generation (see waveform)
    Entry&Start
    1. Power Supply Short
    2. Unlock Request Receive
    3. Lock Request Receive

    NOTICE:
    There are 1 motor and 2 sensors built into the steering lock actuator assembly.

    HINT:
    1. When taking measurements when the lock motor is stopped, it is not necessary to perform any operations.
    2. In order to take measurements when the lock motor is operating, perform either of the following operations:
      1. To unlock the steering, carry the key and turn the engine switch on (ACC) or on (IG) with the shift lever in P.
      2. To lock the steering, turn the engine switch off with the shift lever in P, and then open a door.


    1. C221561E01
      Waveform

      HINT:
      The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.

      Item
      Content
      Tester Connection
      H80-3 (IGE) - H80-1 (GND)
      Tool Setting
      2 V/DIV., 200 ms./DIV.
      Vehicle Condition
      Steering lock motor not operating → Operating → Not operating
      Text in Illustration 
      *a
      Steering lock motor not operating
      *b
      Steering lock motor operating

← PROBLEM SYMPTOMS TABLE (from Dec 2017)DIAGNOSIS SYSTEM (from Oct 2014) →