2014-2019 Hiace · Service Manual STEERING

B2788 IG2 Signal Malfunction

Diagnostic trouble codes · Vehicles built from Jan 2017

Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Dec 2016 from Jan 2017

DESCRIPTION

This DTC is stored when the steering lock ECU detects an IG2 power supply malfunction.

HINT:
The steering lock ECU is not connected to the CAN communication system. However, the steering lock ECU is connected to the certification ECU (smart key ECU assembly) via LIN communication and communicates with other components via CAN communication through the certification ECU (smart key ECU assembly).

DTC No.
Detection Condition
Trouble Area
DTC Output Confirmation Operation
B2788
Mismatch between the steering lock ECU IG2 input from the LIN communication system and from the direct line (1-trip detection logic*).
  1. Steering lock ECU (Steering lock actuator assembly)
  2. Harness or connector
No confirmation operation is necessary (monitoring is continuous).
  1. *: Only output while a malfunction is present and the engine switch is on (IG).
Vehicle Condition and Fail-safe Function when Malfunction Detected 
Vehicle Condition when Malfunction Detected
Fail-safe Function when Malfunction Detected
The steering cannot be locked or unlocked. For this reason, the engine cannot be started.
-
Related Data List and Active Test Items 
DTC No.
Data List Item
Active Test Item
B2788
-
-

WIRING DIAGRAM

C229415E01

INSPECTION PROCEDURE

NOTICE:
  1. When using the GTS with the vehicle engine switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry & Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
  2. The steering lock system uses LIN communication. First perform the inspections in "How to Proceed with Troubleshooting" to confirm that there are no communication malfunctions before proceeding with troubleshooting (Click here).
  3. Inspect the fuses for circuits related to this system before performing the following inspection procedure.
  4. After performing repairs, confirm that no DTCs are output again (Click here).
  5. When replacing the steering lock ECU (steering lock actuator assembly), registration must be performed (Refer to the Service Bulletin).


1. INSPECT STEERING LOCK ECU (POWER SOURCE MODE SIGNAL)
  1. Make sure that there is no looseness at the locking part and the connecting part of the connector.

  1. Disconnect the H80 steering lock ECU (steering lock actuator assembly) connector.

  1. C157850E77
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H80-1 (GND) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Steering Lock ECU (Steering Lock Actuator Assembly))

  1. Reconnect the H80 steering lock ECU (steering lock actuator assembly) connector.

  1. C157849E48
    Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    H80-6 (IG2) - H80-1 (GND)
    Engine switch on (IG)
    11 to 14 V
    H80-6 (IG2) - H80-1 (GND)
    Engine switch off
    Below 1 V

    Text in Illustration 
    *a
    Component with harness connected
    (Steering Lock ECU (Steering Lock Actuator Assembly))



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY) (Click here)


← B2788 IG2 Signal Malfunction (Jan 2015 – Dec 2016)Steering Lock does not Lock (Oct 2014 – Dec 2014) →