2014-2019 Hiace · Service Manual BODY ELECTRICAL

TERMINALS OF ECU

System information · Vehicles built from Oct 2014


INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (BODY ECU)
E288657E01
  1. Disconnect the 13B, 13C, 13E, 13G and H7 instrument panel junction block assembly (body ECU) connectors.

  2. Measure the resistance and voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    13B-3 (L2) - Body ground
    W - Body ground
    Door lock key switch signal
    Front RH door lock key switch off → On (unlock)
    10 kΩ or higher → Below 1 Ω
    13B-4 (UL2) - Body ground
    Y - Body ground
    Door lock key switch signal
    Front RH door lock key switch off → On (lock)
    10 kΩ or higher → Below 1 Ω
    13B-5 (UL1) - Body ground
    Y - Body ground
    Door lock manual switch signal
    Driver side door control switch off → on (unlock)
    10 kΩ or higher → Below 1 Ω
    13B-6 (L1) - Body ground
    W - Body ground
    Door lock manual switch signal
    Driver side door control switch off → On (lock)
    10 kΩ or higher → Below 1 Ω
    13B-21 (L2) - Body ground
    W - Body ground
    Door lock key switch signal
    Front LH door lock key switch off → On (unlock)
    10 kΩ or higher → Below 1 Ω
    13B-22 (UL2) - Body ground
    Y - Body ground
    Door lock key switch signal
    Front LH door lock key switch off → On (lock)
    10 kΩ or higher → Below 1 Ω
    13C-4 (IG) - Body ground
    B - Body ground
    Ignition power supply
    Engine switch off → On (IG)
    Below 1 V → 11 to 14 V
    13E-12 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    13G-1 (BECU) - Body ground
    B-G - Body ground
    Battery power supply
    Always
    11 to 14 V
    H7-4 (LSWD) - Body ground
    W - Body ground
    Front door lock detection switch RH signal
    Front door lock RH lock → Unlock
    10 kΩ or higher → Below 1 Ω

  3. Reconnect the 13B, 13C, 13E, 13G and H7 instrument panel junction block assembly (body ECU) connectors.

  4. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbols)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    13A-10 (ACT+) - Body ground
    L - Body ground
    Back door lock motor drive signal
    Back door control switch off → On (lock)
    Below 1 V → 11 to 14 V → Below 1 V
    13A-18 (RRCY) - Body ground
    W - Body ground
    Rear door courtesy light switch assembly RH signal
    Rear door RH door closed → Open
    1. 11 to 14 V* → Below 1 V
    2. Pulse generation* → Below 1 V
    13A-24 (RRCY) - Body ground
    W - Body ground
    Back door courtesy light switch signal
    Back door door closed → Open
    1. 11 to 14 V* → Below 1 V
    2. Pulse generation* → Below 1 V
    13A-29 (ACT-) - Body ground
    R - Body ground
    Back door lock motor drive signal
    Back door control switch off → On (unlock)
    Below 1 V → 11 to 14 V → Below 1 V
    13A-30 (RRCY) - Body ground
    W - Body ground
    Rear door courtesy light switch assembly LH signal
    Rear door LH door closed → Open
    1. 11 to 14 V* → Below 1 V
    2. Pulse generation* → Below 1 V
    13B-17 (ACT+) - Body ground
    L - Body ground
    Front door lock motor LH/RH drive signal
    Door control switch off → On (lock)
    Below 1 V → 11 to 14 V → Below 1 V
    13B-35 (ACT-) - Body ground
    R - Body ground
    Front door lock motor LH/RH drive signal
    Door control switch off → On (unlock)
    Below 1 V → 11 to 14 V → Below 1 V
    13E-26 (ACT+) - Body ground
    L - Body ground
    Slide door lock motor LH/RH drive signal
    Slide door lock control switch off → On (lock)
    Below 1 V → 11 to 14 V → Below 1 V
    13E-27 (ACT-) - Body ground
    R - Body ground
    Slide door lock motor LH/RH drive signal
    Slide door lock control switch off → On (unlock)
    Below 1 V → 11 to 14 V → Below 1 V
    13E-10 (PCTY) - Body ground
    R - Body ground
    Front door courtesy light switch assembly LH signal
    Front passenger side door closed → Open
    1. 11 to 14 V*3 → Below 1 V
    2. Pulse generation*3 → Below 1 V
    13E-11 (DCTY) - Body ground
    G - Body ground
    Front door courtesy light switch assembly RH signal
    Driver side door closed → Open
    1. 11 to 14 V* → Below 1 V
    2. Pulse generation* → Below 1 V
    H7-6 (HAZ) - Body ground
    W - Body ground
    Hazard warning light signal
    Hazard warning signal switch off → On
    11 to 14 V → Below 1 V
    H7-7 (RDA) - Body ground
    W - Body ground
    Signal input to certification ECU (smart key ECU assembly)
    Procedure:
    1. Engine switch off
    2. All doors closed
    3. All doors locked
    11 to 14 V
    Procedure:
    1. Engine switch off
    2. All doors closed
    3. 10 seconds elapsed after all doors locked
    4. Electrical key transmitter subassembly unlock switch pressed
    Pulse generation
    H7-8 (PRG) - Body ground
    B - Body ground
    Signal output to certification ECU (smart key ECU assembly)
    Procedure:
    1. Engine switch off
    2. All doors closed
    3. All doors locked
    11 to 14 V
    Procedure:
    1. Engine switch off
    2. All doors closed
    3. 10 seconds elapsed after all doors locked
    4. Electrical key transmitter subassembly unlock switch pressed
    Pulse generation
    1. *: The specified value changes depending on vehicle conditions.


CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
B333750E04
  1. Disconnect the B75 certification ECU (smart key ECU assembly) connector.

  2. Measure the resistance and voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    B75-1 (+B) - Body ground
    L - Body ground
    Battery power supply
    Always
    11 to 14 V
    B75-10 (E) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω

  3. Reconnect the B75 certification ECU (smart key ECU assembly) connector.

  4. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbols)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    B75-2 (BZR) - B75-10 (E)
    B - W-B
    Wireless door lock buzzer signal
    Wireless door lock buzzer off
    Below 1 V
    Wireless door lock buzzer on
    Pulse generation
    B75-20 (IG1D) - B75-10 (E)
    B - W-B
    IG Power supply
    Engine switch off → On (IG)
    Below 1 V → 9 to 14 V
    B75-21 (ACCD) - B75-10 (E)
    R - W-B
    ACC Power supply
    Engine switch off → On (ACC)
    Below 1 V → 9 to 14 V
    B76-13 (RDA3) - Body ground
    W - Body ground
    Signal output to instrument panel junction block assembly (body ECU)
    Procedure:
    1. Engine switch off
    2. All doors closed
    3. All doors locked
    11 to 14 V
    Procedure:
    1. Engine switch off
    2. All doors closed
    3. 10 seconds elapsed after all doors locked
    4. Electrical key transmitter subassembly unlock switch pressed
    Pulse generation
    B76-38 (PRG3) - Body ground
    B - Body ground
    Signal input to instrument panel junction block assembly (body ECU)
    Procedure:
    1. Engine switch off
    2. All doors closed
    3. All doors locked
    11 to 14 V
    Procedure:
    1. Engine switch off
    2. All doors closed
    3. 10 seconds elapsed after all doors locked
    4. Electrical key transmitter subassembly unlock switch pressed
    Pulse generation

← PROBLEM SYMPTOMS TABLE (from Jan 2017)DIAGNOSIS SYSTEM (from Oct 2014) →