2014-2019 Hiace · Service Manual TRANSMISSION

P0715 Input / Turbine Speed Sensor Circuit Malfunction

Diagnostic trouble codes · Vehicles built Jan 2017 – Nov 2017

Also covers:

Versions by build date: Jan 2015 – Mar 2016 Apr 2016 – Dec 2016 Jan 2017 – Nov 2017

DESCRIPTION

This sensor detects the rotation speed of the turbine which shows the input turbine speed of the transmission. By comparing the input turbine speed signal (NT) with the output shaft speed sensor signal (SP2), the ECM detects the shift timing of the gears and appropriately controls the engine torque and hydraulic pressure according to various conditions. As a result, the gears shift smoothly.
DTC No.
DTC Detection Condition
Trouble Area
P0715
When the transmission revolution sensor (NT) input voltage is either higher than 1.9 V or below 0.1 V for 4.5 seconds or more (1 trip detection logic).
  1. Open or short in transmission revolution sensor (NT) circuit
  2. Transmission revolution sensor (NT)
  3. ECM
P0717
All conditions are met for 5 seconds or more (1 trip detection logic):
(a) Park/neutral position switch D input signal is ON.
(b) Gear position is 2nd, 3rd, 4th, 5th or 6th.
(c) Transmission output shaft speed is 1000 rpm or more.
(d) The vehicle speed is 9 km/h (5.6 mph) or more.
(e) Transmission revolution sensor (NT) value is less than 300 rpm.
  1. Open or short in transmission revolution sensor (NT) circuit
  2. Transmission revolution sensor (NT)
  3. ECM

MONITOR DESCRIPTION

The transmission revolution sensor (NT) detects the transmission input shaft speed. The ECM calculates gear shifts comparing the transmission revolution sensor (NT) with the transmission revolution sensor (SP2).
While the vehicle is operating in 2nd, 3rd, 4th, 5th or 6th gear with the shift lever in D, if the input shaft speed is less than 300 rpm*1 and the output shaft speed is more than 1000 rpm*2, the ECM interprets this as a fault, illuminates the MIL and stores the DTC.
*1: Pulse is not output or is irregularly output.
*2: The vehicle speed is 50 km/h (31 mph) or more.

WIRING DIAGRAM

C245351E01

INSPECTION PROCEDURE


DATA LIST

HINT:
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the GTS to the DLC3.

  4. Turn the ignition switch to ON.

  5. Turn the GTS on.

  6. Enter the following menus: Powertrain / Engine and ECT / Data List.

  7. According to the display on the GTS, read the Data List.

    Engine and ECT 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    SPD (NT)
    Input shaft speed/
    Min.: 0 rpm
    Max.: 12750 rpm
    1. Lock-up on (after warming up the engine): Value from transmission revolution sensor (NT) equal to engine speed
    2. Lock-up off (idling with shift lever in N): Value from transmission revolution sensor (NT) nearly equal to engine speed
    Data is displayed in increments of 50 rpm

    HINT:
    1. SPD (NT) is always 0 while driving: Open or short in the sensor or circuit.
    2. SPD (NT) is always more than 0 and less than 300 rpm while driving the vehicle at 50 km/h (31 mph) or more: Sensor trouble, improper installation, or intermittent connection trouble of the circuit.


1. READ VALUE USING GTS (SPD (NT) AND NT SENSOR VOLTAGE)
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List

  1. In accordance with the display on the GTS, read the Data List.

    Engine and ECT 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    SPD (NT)
    Input shaft speed/
    Min.: 0 rpm
    Max.: 12750 rpm
    1. Lock-up on (after warming up the engine): Value from transmission revolution sensor (NT) equal to engine speed
    2. Lock-up off (idling with shift lever in N): Value from transmission revolution sensor (NT) nearly equal to engine speed
    Data is displayed in increments of 50 rpm
    NT Sensor Voltage
    Transmission revolution sensor NT output voltage/
    Min.: 0.000 V
    Max.: 4.999 V
    0.1 to 1.9 V: Engine idling
    -
    Result 
    Result
    Proceed to
    Data display is not within Normal Condition range
    A
    Data display is within Normal Condition range
    B



B
REPLACE ECM (Click here)
A


2. INSPECT TRANSMISSION REVOLUTION SENSOR (NT)
  1. Remove the transmission revolution sensor (NT) (Click here).

  1. Connect the battery to the sensor as shown in the illustration.C297974E02

    Text in Illustration 
    *1
    Transmission Revolution Sensor (NT)
    *2
    Ammeter
    *3
    Battery
    *4
    Magnet
    *a
    5 mm (0.197 in.) or less
    -
    -

  1. Wave a magnetic object left and right in front of the transmission revolution sensor (NT) tip (5 mm (0.197 in.) or less) to change the high/low signals while measuring the current.

    NOTICE:
    Make sure to wave the magnetic object during the inspection. The current will not change without waving the magnetic object as indicated by the arrow in the illustration.

  1. Measure the current according to the value(s) in the table below.

    Standard Current:
    Tester Connection
    Condition
    Specified Condition
    1 (NTO) - 2 (NTB)
    Low signal
    4 to 8 mA
    1 (NTO) - 2 (NTB)
    High signal
    12 to 16 mA



NG
REPLACE TRANSMISSION REVOLUTION SENSOR (NT) (Click here)
OK


3. CHECK HARNESS AND CONNECTOR (TRANSMISSION REVOLUTION SENSOR (NT) - ECM)
  1. Disconnect the D113 transmission revolution sensor (NT) connector.

  1. Disconnect the D116 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D113-2 (NTB) - D116-124 (NTB)
    Always
    Below 1 Ω
    D113-1 (NTO) - D116-123 (NTO)
    Always
    Below 1 Ω
    D113-2 (NTB) - Body ground
    Always
    10 kΩ or higher
    D113-1 (NTO) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)


← P0715 Input / Turbine Speed Sensor Circuit Malfunction (+ P0717) (Apr 2016 – Dec 2016)P0717 Input Speed Sensor Circuit No Signal (+ P07BF, P07C0) (from Dec 2017) →