P2808 Pressure Control Solenoid "G" Performance (Shift Solenoid Valve SL4)
Diagnostic trouble codes · Vehicles built from Jan 2017
Versions by build date: Jan 2015 – Mar 2016 Apr 2016 – Dec 2016 from Jan 2017
SYSTEM DESCRIPTION
The ECM uses the vehicle speed signal and signals from the transmission revolution sensors (NT, SP2) to detect the actual gear (1st, 2nd, 3rd, 4th, 5th or 6th gear).The ECM compares the actual gear with the shift schedule in the ECM memory to detect mechanical problems of the shift solenoid valves, transmission valve body assembly or automatic transmission assembly (clutch, brake or gear etc.).
| DTC No. |
DTC Detection Condition |
Trouble Area |
| P2808 |
Either condition is met (2 trip detection logic):
|
|
MONITOR DESCRIPTION
The ECM commands gear shifts by turning the shift solenoid valves on and off. According to the input turbine speed and output shaft speed, the ECM detects the actual gear (1st, 2nd, 3rd, 4th, 5th or 6th gear). When the gear commanded by the ECM and the actual gear are not the same, the ECM illuminates the MIL and stores the DTC.INSPECTION PROCEDURE
- NOTICE:
- Perform registration and/or initialization when parts related to the automatic transmission are replaced (Click here).
| 1. CHECK OTHER DTCS OUTPUT (IN ADDITION TO DTC P2808) |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs using the GTS.
Result Result
Proceed to
Only DTC P2808 is output
A
P2808 and other DTCs are output
B
- HINT:
- If a solenoid is stuck off, DTCs for several solenoids including the malfunctioning solenoid will be detected.
|
|
||||
| B | |
| 2. PERFORM ACTIVE TEST USING GTS (CONTROL THE SHIFT POSITION) |
- NOTICE:
- This test should always be performed with at least 2 people.
Warm up the engine.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Active Test.
According to the display on the GTS, perform the Active Test.
- HINT:
- Comparing the gear commanded by the Active Test with the actual gear enables confirmation of the problem (Click here).
Engine and ECT Tester Display
Test Part
Control Range
Diagnostic Note
Control the Shift Position
Operates the shift solenoid valves to allow gears to be selected manually.
- Press "→" button: Up-shift occurs
- Press "←" button: Down-shift occurs
Can be used to check the operation of the shift solenoid valves.
Up-shifts and down-shifts should be performed consecutively. A 10 seconds interval is required between gear changes.
Do not down-shift at high speeds. Doing so will damage the automatic transmission.
[Vehicle Condition]- 50 km/h (31 mph) or less
- HINT:
- This test can be conducted when the vehicle speed is 50 km/h (30 mph) or less.
- The 4th to 5th and 5th to 6th up-shift must be performed with the accelerator pedal released.
- The 6th to 5th and 5th to 4th down-shift must be performed with the accelerator pedal released.
- Do not operate the accelerator pedal for at least 2 seconds after shifting and do not shift successively.
- The gear commanded by the ECM is shown in the Data List / Shift Status display on the GTS.
- This test can be conducted when the vehicle speed is 50 km/h (30 mph) or less.
Compare the ECM commanded gear and the actual gear.
- Result:
Actual Gear during Malfunction
ECM Commanded Gear
Proceed to
1st
2nd
3rd
4th
5th
6th
Shift solenoid valve SL1
Stuck ON
1st
2nd
3rd
4th
4th
4th
A
Stuck OFF
N*1
N*1
N*1
N*1
5th
6th
Shift solenoid valve SL2
Stuck ON
4th
4th
4th
4th
5th
6th
B
Stuck OFF
1st
2nd
3rd
1st
N*1
N*1
Shift solenoid valve SL3
Stuck ON
2nd
2nd
3rd
4th
5th
6th
C
Stuck OFF
1st
1st
3rd
4th
5th
N*1
Shift solenoid valve SL4
Stuck ON
3rd
3rd
3rd
4th
5th
5th
D
Stuck OFF
1st
2nd
1st
4th
N*1
6th
Shift solenoid valve SLT
Stuck ON
N*2
N*2
N*2
N*2
N*2
N*2
E
Stuck OFF*3
1st
2nd
3rd
4th
5th
6th
- HINT:
- *1: Neutral
- *2: If shift solenoid valve SLT is stuck on, the line pressure will be low. Therefore, the amount of torque that can be transmitted by each gear is lower than the normal limit. When the engine power exceeds this lowered limit, the engine speed will increase freely.
- *3: When shift solenoid valve SLT is stuck off, gear shifting is normal.
- *1: Neutral
|
|
||||
|
|
||||
|
|
||||
|
|
||||
| A | ||
| ||
| 3. INSPECT SHIFT SOLENOID VALVE SL4 |
Remove shift solenoid valve SL4 (Click here).

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
1 - 2
20°C (68°F)
5.0 to 5.6 Ω
Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.
- OK:
Measurement Condition
Specified Condition
- Battery positive (+) with a 21 W bulb → Terminal 1
- Battery negative (-) → Terminal 2
Valve moves and makes an operating noise
- Battery positive (+) with a 21 W bulb → Terminal 1
| *1 |
Shift Solenoid Valve SL4 |
|
|
||||
| OK | |
| 4. INSPECT TRANSMISSION VALVE BODY ASSEMBLY |
Check the transmission valve body assembly (Click here).
- OK:
- There is no foreign matter on each valve and they operate smoothly.
|
|
||||
| OK | ||
| ||
