2014-2019 Hiace · Service Manual HEATER & AIR CONDITIONING SYSTEM

DATA LIST / ACTIVE TEST

System information · Vehicles built from Oct 2014

HINT:
This is used only except 5L-E engine model.


DATA LIST

HINT:
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Connect the GTS to the DLC3.

  2. Turn the ignition switch to ON.

  3. Turn the GTS on.

  4. Enter the following menus:

    1. Body / Air Conditioner / Data List.
    2. Body / Combination Meter / Data List.
    3. Powertrain / Engine and ECT / Data List.

  5. According to the display on the GTS, read the Data List.

    Air Conditioner 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Ambient Temp Sensor
    Cooler thermistor (ambient temperature sensor) /
    Min.: -23.3°C (-9.94°F)
    Max.: 65.95°C (150.71°F)
    Actual ambient temperature displayed
    Open in the circuit: -23.3°C (-9.94°F).
    Short in the circuit: 65.95°C (150.71°F).
    Adjusted Ambient Temp
    Adjusted ambient temperature /
    Min.: -30.8°C (-23.44°F)
    Max.: 50.8°C (123.44°F)
    Adjusted ambient temperature displayed
    -
    Evaporator Fin Thermistor
    No. 1 cooler thermistor /
    Min.: -29.7°C (-21.46°F)
    Max.: 59.55°C (139.19°F)
    Actual evaporator temperature displayed
    Open in the circuit: -29.7°C (-21.46°F).
    Short in the circuit: 59.55°C (139.19°F).
    Evaporator Target Temp
    Target evaporator temperature /
    Min.: -327.68°C (-557.82°F)
    Max.: 327.67°C (621.81°F)
    Target evaporator temperature displayed
    -
    Engine Coolant Temp
    Engine coolant temperature /
    Min.: 1.3°C (34.34°F)
    Max.: 90.55°C (194.99°F)
    Actual engine coolant temperature displayed
    -
    Regulator Pressure Sensor
    Refrigerant pressure sensor /
    Min.: -0.4566 MPa
    Max.: 3.2943 MPa
    Actual refrigerant pressure displayed
    -
    Number of Trouble Codes
    Number of trouble codes / Min.: 0, Max.: 255
    Number of DTCs displayed
    -
    Combination Meter 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Ambient Temperature
    Outside temperature / Min.: -40°C (-40°F), Max.: 87.5°C (189.5°F)
    Almost the same as actual outside temperature
    -


ACTIVE TEST

HINT:
Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Connect the GTS to the DLC3.

  2. Turn the ignition switch to ON.

  3. Turn the GTS on.

  4. Enter the following menus: Body / Air Conditioner / Active Test.

  5. According to the display on the GTS, perform the Active Test.

    Air Conditioner 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Magnetic Clutch Relay
    Magnet clutch relay operation
    ON or OFF
    -

← DTC CHECK / CLEAR (from Jan 2015)DIAGNOSTIC TROUBLE CODE CHART (Oct 2014 – Dec 2014) →