2014-2019 Hiace · Service Manual ENGINE

INSTALLATION

Removal / installation · Vehicles built Jan 2015 – Mar 2016

Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Mar 2016 from Apr 2016


1. INSTALL NO. 1 TURBO WATER PIPE SUB-ASSEMBLY
  1. w/ DPF:

    1. Install a new gasket and the No. 1 turbo water pipe with the bolt and 2 nuts.

      Torque:
      for bolt:
      8.0 N*m{ 82 kgf*cm , 71 in.*lbf }
      for nut:
      12 N*m{ 122 kgf*cm , 9 ft.*lbf }

    2. Install the turbo water hose, No. 2 turbo water hose and No. 13 turbo water hose to the No. 1 turbo water pipe sub-assembly, and slide the 3 clamps to secure the hoses.

  1. w/o DPF:

    1. Install a new gasket and the No. 1 turbo water pipe with the bolt and 2 nuts.

      Torque:
      for bolt:
      8.0 N*m{ 82 kgf*cm , 71 in.*lbf }
      for nut:
      12 N*m{ 122 kgf*cm , 9 ft.*lbf }

    2. Install the No. 1 turbo water hose and No. 2 turbo water hose to the No. 1 turbo water pipe sub-assembly, and slide the 2 clamps to secure the hoses.


2. INSTALL COMPRESSOR INLET ELBOW
  1. w/ DPF:

    1. Install a new gasket and the compressor inlet elbow with the 2 nuts.

      Torque:
      19 N*m{ 194 kgf*cm , 14 ft.*lbf }

    2. Connect the No. 4 turbo water hose to the compressor inlet elbow, and slide the clamp to secure the hose.

  1. w/o DPF:

    1. Install a new gasket and the compressor inlet elbow with the 2 nuts.

      Torque:
      19 N*m{ 194 kgf*cm , 14 ft.*lbf }


3. TEMPORARILY INSTALL TURBOCHARGER
  1. w/ DPF:

    1. Set the turbocharger in a safe location.

    2. Temporarily install the exhaust manifold with the 8 plate washers, 8 new nuts and 8 new collars.

    3. Connect the 3 turbo water hoses to the No. 5 water by-pass pipe sub-assembly and No. 2 water by-pass pipe, and slide the 3 clamps to secure the hoses.

  1. w/o DPF:

    1. Install the No. 2 water by-pass pipe with the bolt and 2 nuts.

      Torque:
      for bolt:
      23 N*m{ 235 kgf*cm , 17 ft.*lbf }
      for nut:
      10 N*m{ 102 kgf*cm , 7 ft.*lbf }

    2. Connect the 2 turbo water hoses to the No. 2 water by-pass pipe, and slide the 2 clamps to secure the hoses.

  1. A148797E04
    Install a new gasket to the turbocharger.
    Text in Illustration 
    *a
    Claw

    NOTICE:
    Install the gasket in the correct direction.

  1. Temporarily install the turbocharger with 3 new nuts.


4. TEMPORARILY INSTALL TURBO OIL INLET PIPE SUB-ASSEMBLY

  1. A262913E02
    Install 3 new gaskets to the turbo oil inlet pipe sub-assembly.
    Text in Illustration 
    *a
    Outside
    *b
    Narrow
    *c
    Wide
    *d
    Claw

    NOTICE:
    Install the gasket in the correct direction.

  1. Temporarily install the turbo oil inlet pipe sub-assembly with the 2 bolts, 2 nuts and union bolt.


5. TEMPORARILY INSTALL TURBOCHARGER STAY
  1. Temporarily install the turbocharger stay with the 2 bolts and a new nut.


6. TIGHTEN TURBOCHARGER
  1. w/ DPF:
    Tighten the 8 nuts to the specified torque to install the exhaust manifold.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }

  1. Tighten the 3 nuts to the specified torque to install the turbocharger.

    Torque:
    52 N*m{ 530 kgf*cm , 38 ft.*lbf }


7. CONNECT TURBOCHARGER STROKE SENSOR CONNECTOR

8. TIGHTEN TURBOCHARGER STAY
  1. Tighten the 2 bolts and nut to the specified torque to install the turbocharger stay.

    Torque:
    38 N*m{ 387 kgf*cm , 28 ft.*lbf }


9. TIGHTEN TURBO OIL INLET PIPE SUB-ASSEMBLY

  1. A262915E02
    Tighten the 2 bolts, 2 nuts and union bolt to install the turbo oil inlet pipe sub-assembly.

    Torque:
    for bolt:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }
    for nut:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }
    for union bolt:
    33 N*m{ 337 kgf*cm , 24 ft.*lbf }

    Text in Illustration 
    *1
    Union Bolt


10. INSTALL NO. 1 AUTOMATIC TRANSMISSION OIL COOLER TUBE CLAMP (for Automatic Transmission)

  1. A239122E01
    Install the No. 1 automatic transmission oil cooler tube clamp with the 2 bolts.

    Torque:
    for bolt A:
    71 N*m{ 724 kgf*cm , 52 ft.*lbf }
    for bolt B:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }


11. INSTALL EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY (w/o DPF)
  1. Install a new gasket and the exhaust manifold converter sub-assembly with 3 new nuts.

    Torque:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }


12. TEMPORARILY INSTALL TURBINE OUTLET ELBOW STAY
  1. w/ DPF:

    1. Temporarily install the turbine outlet elbow stay with the 2 bolts.

  1. w/o DPF:

    1. Temporarily install the turbine outlet elbow stay with the 2 bolts and 2 new nuts.

    2. Tighten the 2 bolts.

      Torque:
      62 N*m{ 632 kgf*cm , 46 ft.*lbf }


13. TEMPORARILY INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR
  1. Temporarily install the No. 1 exhaust manifold heat insulator with the 3 bolts.


14. INSTALL TURBO INSULATOR
  1. Temporarily install the turbo insulator with the 2 bolts.

  1. Tighten the 5 bolts to the specified torque to install the turbo insulator and No. 1 exhaust manifold heat insulator.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }


15. INSTALL TURBINE OUTLET ELBOW (w/ DPF)
  1. Temporarily install the turbine outlet elbow and a new gasket with 3 new nuts.

  1. Temporarily install the No. 3 fuel pipe and a new gasket with the union bolt.

  1. Tighten the 3 nuts of the turbine outlet elbow.

    Torque:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }

  1. Connect the No. 1 turbo water hose to the No. 1 injector holder, and slide the clamp to secure the hose.

  1. Connect the fuel addition injector connector.


16. INSTALL NO. 2 FUEL PIPE CLAMP (w/ DPF)
  1. Temporarily install the No. 2 fuel pipe clamp with the 2 bolts.

  1. Tighten the 2 bolts of the No. 2 fuel pipe clamp and the union bolt of the No. 3 fuel pipe.

    Torque:
    for bolt:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }
    for union bolt:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }

  1. Connect the No. 4 water by-pass pipe to the No. 13 water by-pass hose, and slide the clamp to secure the hose.

  1. Install the No. 4 water by-pass pipe and a new gasket with the union bolt.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }


17. INSTALL CATALYTIC WITH PIPE CONVERTER ASSEMBLY (w/ DPF)

  1. A334694
    Install a new gasket and the catalytic with pipe converter assembly with 3 new nuts.

    Torque:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }

  1. Temporarily install 2 new nuts.

  1. Tighten the 2 bolts of the turbine outlet elbow stay.

    Torque:
    62 N*m{ 632 kgf*cm , 46 ft.*lbf }


18. INSTALL NO. 3 EXHAUST MANIFOLD HEAT INSULATOR (w/ DPF)
  1. Install the No. 3 exhaust manifold heat insulator with the 2 bolts.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }


19. INSTALL NO. 2 EXHAUST MANIFOLD HEAT INSULATOR (w/ DPF)
  1. Install the No. 2 exhaust manifold heat insulator with the 2 bolts.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }


20. INSTALL WIRE HARNESS CLAMP BRACKET
  1. Install the wire harness clamp bracket with the bolt.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

  1. Attach the 3 clamps.


21. INSTALL VENTILATION PIPE
  1. w/ DPF:

    1. Connect the 2 ventilation hoses.

    2. Install the ventilation pipe with the bolt.

      Torque:
      18 N*m{ 184 kgf*cm , 13 ft.*lbf }

    3. for Type A:
      Connect the No. 4 turbo water hose to the ventilation pipe, and slide the clamp to secure the hose.

    4. for Type A:
      Install the No. 14 water by-pass hose to the ventilation pipe, and slide the clamp to secure the hose.

  1. w/o DPF:

    1. Connect the 2 ventilation hoses.

    2. Install the ventilation pipe with the bolt.

      Torque:
      18 N*m{ 184 kgf*cm , 13 ft.*lbf }


22. INSTALL NO. 1 COMPRESSOR MOUNTING BRACKET (w/ Air Conditioning System)

  1. A102453E02
    Temporarily install the No. 1 compressor mounting bracket with the 4 bolts.

    HINT:
    Make sure that the No. 1 compressor mounting bracket is in contact with the cylinder block.

  1. Tighten the 4 bolts in the sequence shown in the illustration.

    Torque:
    45 N*m{ 459 kgf*cm , 33 ft.*lbf }


23. INSTALL COMPRESSOR OUTLET ELBOW

  1. A313566E01
    Install the compressor outlet elbow with the 2 hose clamps and bolt.

    Torque:
    for bolt:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }
    for hose clamp A:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }
    for hose clamp B:
    6.0 N*m{ 61 kgf*cm , 53 in.*lbf }


24. CONNECT TURBOCHARGER MOTOR CONNECTOR

25. INSTALL AIR TUBE ASSEMBLY

  1. A272217E01
    Install the air tube assembly and No. 1 air cleaner hose with the 2 bolts.

    Torque:
    for bolt A:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }
    for bolt B:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }

  1. Tighten the 2 hose clamps.


26. CONNECT NO. 1 AIR CLEANER HOSE
  1. Connect the No. 1 air cleaner hose to the compressor inlet elbow.

    NOTICE:
    Pull the hose to make sure that it is locked and securely connected.


27. INSTALL COMPRESSOR AND MAGNETIC CLUTCH (w/ Air Conditioning System)

E104245E01
  1. Provisionally tighten the compressor and magnetic clutch with the 4 bolts.

  1. Tighten the compressor and magnetic clutch with the 4 bolts.

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }

    NOTICE:
    Tighten the bolts in the order shown in the illustration to install the compressor and magnetic clutch.


28. CONNECT NO. 1 COOLER REFRIGERANT SUCTION HOSE (w/ Air Conditioning System)

29. CONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE (w/ Air Conditioning System)

30. INSTALL FAN AND GENERATOR V BELT (w/ Air Conditioning System)
  1. Rotate the V-ribbed belt tensioner pulley clockwise, and then install the fan and generator V belt.

    NOTICE:
    Make sure that the fan and generator V belt is set properly on each pulley.

  1. Check that the indicator mark of the V-ribbed belt tensioner (Click here).


31. INSTALL NO. 1 TRANSMISSION CONTROL CABLE BRACKET (for Manual Transmission)
  1. Install the No. 1 transmission control cable bracket with the 2 bolts.

    Torque:
    72 N*m{ 729 kgf*cm , 53 ft.*lbf }


32. CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY (for Manual Transmission)

  1. C102659E01
    Install 2 new clips to the No. 1 transmission control cable bracket.

  1. Connect the transmission control cable assembly to the No. 1 transmission control cable bracket.

    NOTICE:
    1. Make sure that A claws of the clips are firmly installed into the bracket grooves.
    2. Make sure that the cable is set in the clip with both B claws erected to prevent slippage of the cable in the opposite direction.

  1. C102206E02
    Align the matchmarks on the control cable assembly and the shift outer lever.

  1. Align the matchmarks on the control cable assembly and the select outer lever.

  1. Install the transmission control cable assembly to the shift outer lever with the nut.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

  1. Install the transmission control cable assembly to the select outer lever with the nut.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }


33. INSTALL FRONT EXHAUST PIPE ASSEMBLY (w/ DPF)
(Click here)

34. INSTALL FRONT EXHAUST PIPE ASSEMBLY (w/o DPF)

  1. A104634
    Inspect the compression spring.

    1. Using a vernier caliper measure the free length of the compression spring.

      Minimum length:
      40.5 mm (1.59 in.)

      If the free length is less than the minimum, replace the compression spring.

  1. A144621E02
    Fully push a new gasket onto the exhaust manifold converter sub-assembly by hand.
    Text in Illustration 
    *1
    Gasket
    *a
    Wooden Block

  1. Using a wooden block, uniformly strike the gasket so that the gasket and exhaust manifold converter sub-assembly fit together properly.

    NOTICE:
    1. Install the gasket in the correct direction.
    2. Do not damage the outer surface of the gasket.
    3. Do not reuse the removed gasket.
    4. Do not push in the gasket with the front exhaust pipe assembly when connecting the pipe.

  1. Connect the front exhaust pipe assembly to the No. 4 exhaust pipe support.

  1. Install the front exhaust pipe assembly and 2 compression springs with the 2 bolts and 2 nuts.

    Torque:
    for bolt:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }
    for nut:
    48 N*m{ 489 kgf*cm , 35 ft.*lbf }


35. TIGHTEN EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY (w/o DPF)

  1. A242357
    Tighten the 2 nuts to the exhaust manifold converter sub-assembly.

    Torque:
    62 N*m{ 632 kgf*cm , 46 ft.*lbf }


36. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

37. ADD ENGINE COOLANT
  1. Firmly tighten the drain plugs.

  1. Fill the radiator reservoir assembly with engine coolant to the top of the inlet.

    Standard Capacity:
    Item
    Specified Condition
    w/o Heater
    13.2 liters (13.9 US qts, 11.6 Imp. qts)
    w/ Front Heater
    14.2 liters (15.0 US qts, 12.5 Imp. qts)
    w/ Front and Rear Heaters
    16.2 liters (17.1 US qts, 14.3 Imp. qts)

    NOTICE:
    Do not substitute plain water for engine coolant.

    HINT:
    1. Use of improper coolants may damage the engine cooling system.
    2. Use only Toyota Super Long Life Coolant or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, and non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).

  1. Loosen the bleeder plug of the outlet housing.

  1. When air is bled and the engine coolant drains out, firmly tighten the bleeder plug.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. A142533
    Add engine coolant up to the B line mark in the radiator reservoir assembly and install the radiator reservoir cap sub-assembly.

  1. Warm up the engine until the thermostat opens.

    1. While the thermostat is open, circulate the engine coolant for several minutes.

      HINT:
      The thermostat open timing can be confirmed by pressing the No. 3 radiator hose by hand, and checking when the engine coolant starts to flow inside the hose.

  1. A142532
    After the engine cools down, check that the engine coolant level is between the LOW and FULL level marks.


38. CHARGE REFRIGERANT (w/ Air Conditioning System)
  1. Perform vacuum purging using a vacuum pump.

  1. Charge with refrigerant HFC-134a (R134a).

    E100257E01

    Standard:
    Single A/C:
    520 to 580g (18.3 to 20.5 oz.)
    Dual A/C:
    670 to 730g (23.0 to 25.7 oz.)

    SST
    07110-58060   (07117-58090, 07117-78050, 07117-58070, 07117-58060, 07117-58080, 07117-88060, 07117-88070, 07117-88080)

    NOTICE:
    1. Do not operate the cooler compressor before charging refrigerant as the cooler compressor does not work properly without any refrigerant, which causes the compressor to overheat.
    2. Approximately 100 g (3.5 oz.) of refrigerant may need to be charged after bubbles disappear. The refrigerant amount should be checked by quantity, and not with the sight glass.

    HINT:
    Prepare a service can to recharge refrigerant if using the refrigerant gas collected with the freon collection/recycling device because the collective rate of the device is approximately 90%.


39. WARM UP ENGINE
  1. Warm up the engine at less than 1,850 rpm for 2 minutes or more after charging refrigerant.

    NOTICE:
    Be sure to warm up the compressor when turning the A/C switch on after removing and installing the cooler refrigerant lines (including the compressor), to prevent damage to the compressor.


40. CHECK FOR REFRIGERANT LEAK (w/ Air Conditioning System)
  1. After recharging refrigerant gas, check for leakage of refrigerant gas using a halogen leak detector.

  1. Carry out the test under the following conditions:

    1. Stop the engine.
    2. Secure good ventilation (the gas leak detector may react to volatile gases which are not refrigerant, such as evaporated gasoline and exhaust gas).
    3. Repeat the test 2 or 3 times.
    4. Make sure that there is some refrigerant remaining in the refrigeration system.
      When the compressor is off: approx. 392 to 588 kPa (4 to 6 kgf/cm2, 57 to 85 psi)

  1. I042222E02
    Using a gas leak detector, check for leakage of the refrigerant line.

  1. N014519E01
    Bring the gas leak detector close to the drain hose with the detector's power off.

    HINT:
    1. After the blower motor has stopped, let the cooling unit stand for more than 15 minutes.
    2. Bring the gas leak detector sensor under the drain hose.
    3. When bringing the gas leak detector close to the drain hose, make sure that the gas leak detector does not react to volatile gases.
      If such reaction is unavoidable, the vehicle must be lifted up.

  1. If a gas leak is not detected on the drain hose, remove the blower motor control from the cooling unit. Insert the gas leak detector sensor into the unit and perform the test.

  1. Disconnect the pressure switch connector and leave it for approximately 20 minutes. Bring the gas leak detector close to the pressure switch and perform the test.


41. INSPECT FOR COOLANT LEAK

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Hot, pressurized engine coolant and steam may be released and cause serious burns.

  1. Fill the radiator with coolant and attach a radiator cap tester to the radiator.

  1. Warm up the engine.

  1. Using a radiator cap tester, increase the pressure inside the radiator to 137 kPa (1.4 kgf/cm2, 19.9 psi), and check that the pressure does not drop.

    HINT:
    If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and cylinder head.


42. INSPECT FOR OIL LEAK
  1. Start the engine. Make sure that there are no oil leaks from the areas that were worked on.


43. INSPECT FOR EXHAUST GAS LEAK
If gas is leaking, tighten the areas necessary to stop the leak. Replace damaged parts as necessary.

44. INSTALL FENDER APRON MUDGUARD SEAL RH

45. INSTALL ENGINE SERVICE HOLE SUB COVER SUB-ASSEMBLY
  1. Install the engine service hole sub cover with the 5 bolts.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }


46. INSTALL FRONT SEAT ASSEMBLY RH

  1. B107528
    Connect the front seat inner belt assembly connector and install the front seat assembly.

  1. Align the front seat assembly adjuster pin with the holes in the body.

  1. Move the front seat assembly to the rearmost position.

    NOTICE:
    Make sure that the front seat assembly is securely locked.

  1. Temporarily tighten the 2 bolts on the front side of the front seat assembly.

  1. Move the front seat assembly fully forward.

    NOTICE:
    Make sure that the front seat assembly is securely locked.

  1. Temporarily tighten the 2 bolts on the rear side of the front seat assembly.

  1. Move the front seat assembly to the rearmost position.

    NOTICE:
    Make sure that the front seat assembly is securely locked.

  1. Fully tighten the 2 bolts on the front side of the front seat assembly in the order of outer and inner side.

    Torque:
    39 N*m{ 398 kgf*cm , 29 ft.*lbf }

  1. Move the front seat assembly fully forward.

    NOTICE:
    Make sure that the front seat assembly is securely locked.

  1. Fully tighten the 2 bolts on the rear side of the front seat assembly in the order of outer and inner side.

    Torque:
    39 N*m{ 398 kgf*cm , 29 ft.*lbf }


47. INSTALL FRONT DOOR SCUFF PLATE RH

48. INSTALL NO. 2 ENGINE UNDER COVER (for Cold Area Specification Vehicles)
  1. Install the No. 2 engine under cover with the 6 bolts.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }


49. INSTALL NO. 1 ENGINE UNDER COVER (for Cold Area Specification Vehicles)
  1. Install the No. 1 engine under cover with the 4 bolts.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }

← INSTALLATION (Oct 2014 – Dec 2014)INSTALLATION (from Apr 2016) →