2014-2019 Hiace · Service Manual RESTRAINTS

B1617/84 Lost Communication with Front Airbag Sensor LH

Diagnostic trouble codes · Vehicles built Apr 2016 – Dec 2016

Also covers:

Versions by build date: Jan 2015 – Mar 2016 Apr 2016 – Dec 2016 from Jan 2017

DESCRIPTION

The front airbag sensor LH circuit consists of the center airbag sensor assembly and front airbag sensor LH.
The front airbag sensor LH detects impacts to the vehicle and sends signals to the center airbag sensor assembly to determine if the airbag should be deployed.
DTC B1617/84 or B1618/84 is stored when a malfunction is detected in the front airbag sensor LH circuit.
DTC Code
DTC Detection Condition
Trouble Area
B1617/84
One of the following conditions is met:
  1. The center airbag sensor assembly detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in the front airbag sensor LH circuit for 2 seconds.
  2. A front airbag sensor LH malfunction.
  3. A center airbag sensor assembly malfunction.
  1. Wire cowl to headlight harness assembly
  2. Engine room main wire
  3. Front airbag sensor LH
  4. Center airbag sensor assembly
B1618/84
One of the following conditions is met:
  1. The center airbag sensor assembly detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in the front airbag sensor LH circuit for 2 seconds.
  2. A front airbag sensor LH malfunction.
  3. A center airbag sensor assembly malfunction.
  1. Wire cowl to headlight harness assembly
  2. Engine room main wire
  3. Front airbag sensor LH
  4. Center airbag sensor assembly

WIRING DIAGRAM

C279108E12
C279108E13

INSPECTION PROCEDURE

NOTICE:
  1. When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (Click here).
  2. After replacing the center airbag sensor assembly, refer to initialization (Click here).


1. CHECK CONNECTION OF CONNECTORS
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor assembly and front airbag sensor LH.

    OK:
    The connectors are properly connected.



NG
CONNECT CONNECTORS PROPERLY
OK


2. CHECK CONNECTORS
  1. Disconnect the connectors from the center airbag sensor assembly and front airbag sensor LH.

  1. C208241E02
    Check that the connectors (on the center airbag sensor assembly side and front airbag sensor LH side) are not damaged.

    OK:
    The connectors are not deformed or damaged.

    Text in Illustration 
    *1
    Front Airbag Sensor LH
    *2
    Center Airbag Sensor Assembly
    *3
    Wire Cowl to Headlight Harness Assembly
    *4
    Engine Room Main Wire



NG
REPLACE HARNESS AND CONNECTOR
OK


3. CHECK FRONT AIRBAG SENSOR LH CIRCUIT

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.C213917E08

    Text in Illustration 
    *1
    Front Airbag Sensor LH
    *2
    Center Airbag Sensor Assembly
    *3
    Connector E
    *4
    Connector B
    *5
    Service Wire
    *6
    Wire Cowl to Headlight Harness Assembly
    *7
    Engine Room Main Wire
    -
    -
    *a
    Front view of wire harness connector
    (to Front Airbag Sensor LH)
    *b
    Rear view of wire harness connector
    (to Center Airbag Sensor Assembly)

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A13-2 (+SL) - Body ground
    Ignition switch ON
    Below 1 V
    A13-1 (-SL) - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Using a service wire, connect terminals 30 (+SL) and 28 (-SL) of connector B.

    NOTICE:
    Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A13-2 (+SL) - A13-1 (-SL)
    Always
    Below 1 Ω

  1. Disconnect the service wire from connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A13-2 (+SL) - A13-1 (-SL)
    Always
    1 MΩ or higher
    A13-2 (+SL) - Body ground
    Always
    1 MΩ or higher
    A13-1 (-SL) - Body ground
    Always
    1 MΩ or higher

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Return the front airbag sensor LH and RH to their original positions and connect the connectors to them.



NG
Go to step 5
OK


4. CHECK FRONT AIRBAG SENSOR LH

  1. C148689E42
    Connect the connectors to the center airbag sensor assembly.

  1. Interchange the front airbag sensor LH with RH and connect the connectors to them.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    Result 
    Result
    Proceed to
    DTC B1617 or B1618 is output
    A
    DTC B1612 or B1613 is output
    B
    DTC B1612, B1613, B1617 and B1618 are not output
    C

    HINT:
    Codes other than DTC B1612, B1613, B1617 and B1618 may be output at this time, but they are not related to this check.

    Text in Illustration 
    *1
    Front Airbag Sensor RH
    *2
    Center Airbag Sensor Assembly



A
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)

B
REPLACE FRONT AIRBAG SENSOR LH (Click here)
C

USE SIMULATION METHOD TO CHECK (Click here)

5. CHECK ENGINE ROOM MAIN WIRE

  1. Disconnect the wire cowl to headlight harness assembly connector from the engine room main wire.C323788E01

    Text in Illustration 
    *A
    for LHD
    *B
    for RHD
    *1
    Front Airbag Sensor LH
    *2
    Center Airbag Sensor Assembly
    *3
    Wire Cowl to Headlight Harness Assembly
    *4
    Engine Room Main Wire
    *5
    Connector C
    *6
    Connector B
    *7
    Service Wire
    -
    -
    *a
    Front view of wire harness connector
    (to Engine Room Main Wire)
    *b
    Rear view of wire harness connector
    (to Center Airbag Sensor Assembly)

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    for LHD:
    Tester Connection
    Switch Condition
    Specified Condition
    AB2-2 (+SL) - Body ground
    Ignition switch ON
    Below 1 V
    AB2-4 (-SL) - Body ground
    Ignition switch ON
    Below 1 V
    for RHD:
    Tester Connection
    Switch Condition
    Specified Condition
    AB3-2 (+SL) - Body ground
    Ignition switch ON
    Below 1 V
    AB3-4 (-SL) - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Using a service wire, connect terminals 30 (+SL) and 28 (-SL) of connector B.

    NOTICE:
    Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD:
    Tester Connection
    Condition
    Specified Condition
    AB2-2 (+SL) - AB2-4 (-SL)
    Always
    Below 1 Ω
    for RHD:
    Tester Connection
    Condition
    Specified Condition
    AB3-2 (+SL) - AB3-4 (-SL)
    Always
    Below 1 Ω

  1. Disconnect the service wire from connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD:
    Tester Connection
    Condition
    Specified Condition
    AB2-2 (+SL) - AB2-4 (-SL)
    Always
    1 MΩ or higher
    AB2-2 (+SL) - Body ground
    Always
    1 MΩ or higher
    AB2-4 (-SL) - Body ground
    Always
    1 MΩ or higher
    for RHD:
    Tester Connection
    Condition
    Specified Condition
    AB3-2 (+SL) - AB3-4 (-SL)
    Always
    1 MΩ or higher
    AB3-2 (+SL) - Body ground
    Always
    1 MΩ or higher
    AB3-4 (-SL) - Body ground
    Always
    1 MΩ or higher



NG
REPLACE ENGINE ROOM MAIN WIRE
OK

REPLACE WIRING COWL TO HEADLAMP HARNESS ASSEMBLY


← B1617/84 Lost Communication with Front Airbag Sensor LH (+ B1618/84) (Jan 2015 – Mar 2016)B1617/84 Lost Communication with Front Airbag Sensor LH (+ B1618/84) (from Jan 2017) →