2014-2019 Hiace · Service Manual TRANSMISSION

P0720 Output Speed Sensor Circuit

Diagnostic trouble codes · Vehicles built Jan 2017 – Nov 2017

Also covers:

Versions by build date: Jan 2015 – Mar 2016 Apr 2016 – Dec 2016 Jan 2017 – Nov 2017

DESCRIPTION

This sensor detects the rotation speed of the transmission output shaft and sends signals to the ECM. By comparing the input turbine speed signal (NT) with the output shaft speed sensor signal (SP2), the ECM detects the shift timing of the gears and appropriately controls the engine torque and hydraulic pressure according to various conditions. As a result, the gears shift smoothly.
DTC Code
DTC Detection Condition
Trouble Area
P0720
When the transmission revolution sensor (SP2) input voltage is either higher than 1.9 V or below 0.1 V for 4.5 seconds or more (2 trip detection logic).
  1. Open or short in transmission revolution sensor (SP2) circuit
  2. Transmission revolution sensor (SP2)
  3. ECM
P0722
All conditions are met for 5 seconds or more (2 trip detection logic):
(a) Park/neutral position switch D input signal is ON.
(b) Either condition is met.
  1. Gear position is 1st:
    Transmission revolution sensor (NT) value is more than 1240 rpm.
  2. Gear position is 2nd, 3rd, 4th, 5th or 6th:
    Transmission revolution sensor (NT) value is more than 720 rpm.
(c) The vehicle speed is 9 km/h (5.6 mph) or more.
(d) No signal from transmission revolution sensor (SP2) is input to the ECM.
  1. Open or short in transmission revolution sensor (SP2) circuit
  2. Transmission revolution sensor (SP2)
  3. ECM

MONITOR DESCRIPTION

The transmission revolution sensor (SP2) detects the transmission output shaft speed. The ECM calculates gear shifts comparing the transmission revolution sensor (NT) with the transmission revolution sensor (SP2).
If the ECM detects no signal from the transmission revolution sensor (SP2) even while the vehicle is moving, it will conclude that there is a malfunction in the transmission revolution sensor (SP2). The ECM will illuminate the MIL and store the DTC.

WIRING DIAGRAM

C245351E02

INSPECTION PROCEDURE


DATA LIST

HINT:
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the GTS to the DLC3.

  4. Turn the ignition switch to ON.

  5. Turn the GTS on.

  6. Enter the following menus: Powertrain / Engine and ECT / Data List.

  7. According to the display on the GTS, read the Data List.

    Engine and ECT 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    SPD (SP2)
    Output shaft speed/
    Min.: 0 km/h (0 mph)
    Max.: 255 km/h (158 mph)
    0 km/h (0 mph): Vehicle stopped (equal to vehicle speed)
    -

    HINT:
    1. SPD (SP2) is always 0 while driving: Open or short in the sensor or circuit.
    2. SPD (SP2) value displayed on the GTS is much lower than the actual vehicle speed: Sensor trouble, improper installation, or intermittent connection trouble of the circuit.


1. READ VALUE USING GTS (SPD (SP2) AND SP2 SENSOR VOLTAGE)
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List

  1. In accordance with the display on the GTS, read the Data List.

    Engine and ECT 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    SPD (SP2)
    Output shaft speed/
    Min.: 0 km/h (0 mph)
    Max.: 255 km/h (158 mph)
    0 km/h (0 mph): Vehicle stopped (equal to vehicle speed)
    -
    SP2 Sensor Voltage
    Transmission revolution sensor SP2 output voltage/
    Min.: 0.000 V
    Max.: 4.999 V
    0.1 to 1.9 V: Engine idling
    -
    Result 
    Result
    Proceed to
    Data display is not within Normal Condition range
    A
    Data display is within Normal Condition range
    B



B
REPLACE ECM (Click here)
A


2. INSPECT TRANSMISSION REVOLUTION SENSOR (SP2)
  1. Remove the transmission revolution sensor (SP2) (Click here).

  1. Connect the battery to the sensor as shown in the illustration.C297974E03

    Text in Illustration 
    *1
    Transmission Revolution Sensor (SP2)
    *2
    Ammeter
    *3
    Battery
    *4
    Magnet
    *a
    5 mm (0.197 in.) or less
    -
    -

  1. Wave a magnetic object left and right in front of the transmission revolution sensor (SP2) tip (5 mm (0.197 in.) or less) to change the high/low signals while measuring the current.

    NOTICE:
    Make sure to wave the magnetic object during the inspection. The current will not change without waving the magnetic object as indicated by the arrow in the illustration.

  1. Measure the current according to the value(s) in the table below.

    Standard Current:
    Tester Connection
    Condition
    Specified Condition
    1 (SP2O) - 2 (SP2B)
    Low signal
    4 to 8 mA
    1 (SP2O) - 2 (SP2B)
    High signal
    12 to 16 mA



NG
REPLACE TRANSMISSION REVOLUTION SENSOR (SP2) (Click here)
OK


3. CHECK HARNESS AND CONNECTOR (TRANSMISSION REVOLUTION SENSOR (SP2) - ECM)
  1. Disconnect the D114 transmission revolution sensor (SP2) connector.

  1. Disconnect the D116 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D114-2 (SP2B) - D116-126 (SP2B)
    Always
    Below 1 Ω
    D114-1 (SP2O) - D116-125 (SP2O)
    Always
    Below 1 Ω
    D114-2 (SP2B) - Body ground
    Always
    10 kΩ or higher
    D114-1 (SP2O) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)


← P0720 Output Speed Sensor Circuit (+ P0722) (Apr 2016 – Dec 2016)P0722 Output Speed Sensor Circuit No Signal (+ P077C, P077D) (from Dec 2017) →