2014-2019 Hiace · Service Manual BODY ELECTRICAL

B27A9 Open in Indoor Electrical Key Oscillator Circuit

Diagnostic trouble codes · Vehicles built Dec 2015 – Mar 2016

Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Nov 2015 Dec 2015 – Mar 2016 Apr 2016 – Dec 2016 Jan 2017 – Nov 2017 from Dec 2017

DESCRIPTION

When any door is opened or closed, or the engine switch is pressed, the certification ECU (smart key ECU assembly) generates a request signal and sends it to the No. 2 indoor electrical key antenna assembly (front floor). For the No. 2 indoor electrical key antenna assembly (front floor) to detect when the electrical key transmitter sub-assembly is inside the vehicle, the signal from the certification ECU (smart key ECU assembly) requesting a response from the electrical key transmitter sub-assembly is transmitted inside the vehicle.
DTC B27A9 is stored by the certification ECU (smart key ECU assembly) when an open circuit is detected between the certification ECU (smart key ECU assembly) and No. 2 indoor electrical key antenna assembly (front floor) (between terminals CGND and ANTE7, or terminals CG6B and CLGB).
DTC Code
DTC Detection Condition
Trouble Area
DTC Output Confirmation Operation
B27A9
An open circuit is detected in the circuit between the certification ECU (smart key ECU assembly) and No. 2 indoor electrical key antenna assembly (front floor) (CGND - ANTE7, CG6B - CLGB) (1 trip detection logic*).
  1. Harness or connector
  2. No. 2 indoor electrical key antenna assembly (front floor)
  3. Certification ECU (smart key ECU assembly)
Any time
  1. *: Only output while a malfunction is present.
Vehicle Condition and Fail-safe Operation when Malfunction Detected 
Vehicle Condition when Malfunction Detected
Fail-safe Operation when Malfunction Detected
  1. Power source mode does not change when engine switch pressed
  2. Electrical key transmitter sub-assembly locked inside vehicle
-
Related Data List and Active Test 
DTC Code
Data List and Active Test
B27A9
Key diagnostic mode can be used to perform troubleshooting

WIRING DIAGRAM

B286267E41

INSPECTION PROCEDURE

NOTICE:
  1. The smart entry and start system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here). Troubleshoot the smart entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.
  2. When using the GTS with the vehicle engine switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
  3. Before replacing the certification ECU (smart key ECU assembly), refer to the smart entry and start system (for Entry Function) precaution (Click here).
  4. After repair, confirm that no DTCs are output by performing the "DTC Output Confirmation Operation".


1. CHECK CONNECTOR CONNECTION
  1. Turn the engine switch off.

  1. Check that the connectors are properly connected to the certification ECU (smart key ECU assembly) and No. 2 indoor electrical key antenna assembly (front floor).

    OK:
    Connectors are properly connected.



NG
CONNECT CONNECTORS PROPERLY
OK


2. CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - NO. 2 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY [FRONT FLOOR])
  1. Disconnect the B76 certification ECU (smart key ECU assembly) connector.

  1. Disconnect the R5 No. 2 indoor electrical key antenna assembly (front floor) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    B76-28 (CGND) - R5-1 (ANTE7)
    Always
    Below 1 Ω
    B76-27 (CG6B) - R5-2 (CLGB)
    Always
    Below 1 Ω
    B76-28 (CGND) or R5-1 (ANTE7) - Body ground
    Always
    10 kΩ or higher
    B76-27 (CG6B) or R5-2 (CLGB) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO NO. 2 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY [FRONT FLOOR])
  1. Connect the B76 certification ECU (smart key ECU assembly) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    B75-10 (E) - Body ground
    Always
    Below 1 Ω

  1. Using an oscilloscope, check the waveform.B333754E08

    Text in Illustration 
    *a
    Component with harness connected
    (Certification ECU [Smart Key ECU Assembly])
    *b
    Waveform 1
    *c
    Within approximately 30 seconds from when the door is closed
    *d
    After approximately 30 seconds from when the door is closed

    OK:
    Tester Connection
    Condition
    Tool Setting
    Specified Condition
    B76-28 (CGND) - B75-10 (E)
    Procedure:
    1. Engine switch off
    2. Electrical key transmitter sub-assembly not inside vehicle
    3. Door is open
    4. Door is closed
    5. Within 30 seconds
    2 V/DIV., 500 ms/DIV.
    Pulse generation (See waveform 1)
    B76-27 (CG6B) - B75-10 (E)
    Procedure:
    1. Engine switch off
    2. Electrical key transmitter sub-assembly not inside vehicle
    3. Door is open
    4. Door is closed
    5. Within 30 seconds
    2 V/DIV., 500 ms/DIV.
    Pulse generation (See waveform 1)



NG
REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
OK


4. REPLACE NO. 2 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (FRONT FLOOR)
  1. Temporarily replace the No. 2 indoor electrical key antenna assembly (front floor) with a new or known good one (Click here).


NEXT


5. CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


6. CHECK FOR DTC
  1. Check for DTCs (Click here).

    OK:
    DTC B27A9 is not output.



NG
REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
OK

END (NO. 2 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY [FRONT FLOOR] WAS DEFECTIVE)


← B27A9 Open in Indoor Electrical Key Oscillator Circuit (Jan 2015 – Nov 2015)B27A9 Open in Indoor Electrical Key Oscillator Circuit (Apr 2016 – Dec 2016) →