Turbocharger Noise
Circuit diagnosis · Vehicles built from Jan 2017
Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Mar 2016 Apr 2016 – Dec 2016 from Jan 2017
DESCRIPTION
- HINT:
- Turbocharger noise is classified into 2 types. One is whistling noise, and the other is whining noise. When troubleshooting, the type of noise should be determined first.
| Noise Type |
Noise Description |
Main Trouble Area |
| Whistling noise |
The volume and pitch of this noise are proportional to turbocharger speed or engine speed. Therefore, the noise level will become more obvious when engine speed increases. |
|
| Whining noise |
This noise has a lower pitch than whistling noise. It generally occurs in the engine speed range of 1500 to 2500 rpm, and has a relatively constant pitch, independent of engine speed and vehicle speed. |
Turbocharger
|
| Faults and Symptoms of Diesel Engine Components |
| Main fault |
Turbocharger turbine shaft imbalance |
|
| Symptoms |
High-pitched whistling noise
|
|
| Main fault |
Leakage |
|
| Symptoms |
Leak flow noise |
|
| Symptoms |
Gear noise
|
|
| Symptoms |
Gear noise
|
|
INSPECTION PROCEDURE
| 1. CONFIRM CONDITION IN WHICH NOISE OCCURRED |
Confirm with the customer the conditions in which the noise occurred.
- HINT:
- To clearly understand the conditions in which the noise occurred, the items in the table below are useful.
Item
Note
Engine speed
Engine speed range
Vehicle speed
Vehicle speed range
Transmission gear
Which gear?
Accelerator pedal position
During acceleration or deceleration?
Temperature
- Ambient temperature
- Engine temperature (cold, warmed up, etc.)
Road conditions
- City or highway driving
- Uphill or downhill
Noise level
- Did the noise occur suddenly, or build gradually?
- Has the noise gradually been getting louder?
Other symptoms
- Lack of power
- High fuel consumption, etc.
Noise recognition
What made the customer determine the noise to be abnormal?
| NEXT | |
| 2. CONFIRM NOISE CUSTOMER MENTIONED (PROCEDURE 2) |
Check for the noise described by the customer.
- HINT:
- If a noise is heard, make sure that the noise matches the noise described by the customer.
Result Result
Proceed to
Obvious abnormal noise matching noise described by customer is confirmed
A
Obvious abnormal noise matching noise described by customer is not confirmed
B
|
|
||||
| A | |
| 3. CHECK INTAKE SYSTEM |
Check for air leakage between the air cleaner and turbocharger, and between the turbocharger and intake manifold.
- HINT:
- Check for disconnected or improperly connected hoses, and gaps between hoses and parts.
- Check for foreign matter between the air cleaner and turbocharger.
- Check for disconnected or improperly connected hoses, and gaps between hoses and parts.
|
|
||||
| OK | |
| 4. CONFIRM NOISE SOURCE (FROM TURBOCHARGER OR NOT) |
Disconnect the actuator hose from the compressor housing.
Close the compressor housing side tube with a hose clip or equivalent.
Using SST, apply pressure to the actuator to open the waste gate valve.

- Valve opening pressure:
- Specified pressure* (See table below)
- NOTICE:
- Never apply more than the predetermined maximum pressure* to the actuator.
- HINT:
- *: Valve opening pressure and predetermined maximum pressure above differ according to the turbocharger. For the specifications, see the table below.
Specifications: Turbocharger Sub-assembly
(Part No.)
Valve Opening Pressure
(kPa: Gauge Pressure)
Maximum Pressure
(kPa: Gauge Pressure)
Reference:
Rod Stroke
(mm)
17201-30070
130
147.8
0.89 to 1.74
17201-30080
119
136
0.98 to 1.91
- SST
- 09992-00242
Check that the actuator rod moves and that the waste gate valve opens.
Start the engine and allow it to idle.
Rev the engine several times by depressing the accelerator pedal.
- NOTICE:
- Do not rev the engine without applying sufficient pressure to the actuator. The boost pressure (turbocharged air pressure) may exceed the prescribed boost pressure limit and the engine may be damaged due to overboost.
Check whether the noise is reduced or not compared with the noise under the original conditions.
Reconnect the actuator hose to the compressor housing.
Result Result
Proceed to
The noise is reduced (or disappears)
A
The noise is the same as in Procedure 2 (the noise does not change)
B
- HINT:
- When the waste gate valve opens, the turbocharger speed decreases regardless of the engine condition. Therefore, it is possible to determine whether the cause of the noise is the turbocharger or not.
- If the turbocharger is the cause of the noise, the noise will be reduced when the waste gate valve opens because turbocharger speed decreases.
- When the waste gate valve opens, the turbocharger speed decreases regardless of the engine condition. Therefore, it is possible to determine whether the cause of the noise is the turbocharger or not.
|
|
||||
| A | |
| 5. CONFIRM THE NOISE TYPE |
Check whether the noise can be heard even when the engine speed is more than 3000 rpm, and whether the noise gradually gets louder as the engine speed increases.
- HINT:
- If so, the noise is likely to be whistling noise. If not, the noise is likely to be whining noise.
Result Result
Proceed to
Yes (The noise is likely to be whistling noise)
A
No (The noise is likely to be whining noise)
B
|
|
||||
| A | ||
| ||
| 6. PERFORM ALIGNMENT OF EXHAUST PIPE AND CONFIRM THE NOISE |
Disconnect the exhaust pipe at the ball joint and from each exhaust pipe support, and then realign the exhaust pipe and reconnect it to each exhaust pipe support and at the ball joint (Click here).


| *1 |
Outlet Pipe |
*2 |
Gasket (Ball Joint) |
| *3 |
Compression Spring |
*4 |
Front Exhaust Pipe Assembly |
| *5 |
Exhaust Pipe Support |
*6 |
Gasket |
| *7 |
Center Exhaust Pipe Assembly |
- |
- |
| *a |
Specified torque |
*b |
Non-reusable part |
- HINT:
- Above illustration is an example.
Confirm whether the noise problem is solved or not.
- HINT:
- The alignment of the exhaust pipe affects whining noise.
Result Result
Proceed to
The noise problem is solved
A
The noise problem remains
B
|
|
||||
| A | ||
| ||
| 7. CHECK FOR NOISE FROM SOURCE OTHER THAN TURBOCHARGER (PROCEDURE 7) |
Check for the noise source with a sound scope.
- NOTICE:
- When performing this check, make sure that the sound scope, your body, etc., do not get caught on the V-belt.
- HINT:
- The source of the noise is not the turbocharger, but a part other than the turbocharger (e.g. a part inside the engine, transmission, or vacuum pump).
- Sometimes gear noise may be mistaken for turbocharger noise. For gear noise, pay attention to the gear inside the engine and transmission gear.
- Rev the engine up and check if the noise reduces at the same time the engine speed decreases. If the noise reduces at the same time the engine speed decreases, it is gear noise. If the noise reduces a short time after the engine speed decreases, it is turbocharger noise.
- The following illustration is a reference for checking whether the noise source is from the engine.
- The source of the noise is not the turbocharger, but a part other than the turbocharger (e.g. a part inside the engine, transmission, or vacuum pump).


Text in Illustration *1
Timing Belt
*2
Camshafts
*3
Crankshaft
*4
Timing Gear Train
*a
Gear Location inside Engine
-
-
- HINT:
- Above illustration is an example.
- Gear noise can be confirmed with a sound scope. Put the sound scope on the cylinder block near the gear, and if the noise heard through the sound scope has the same timing as the noise heard without the sound scope, it is gear noise.
- Above illustration is an example.
| NEXT | |
| 8. REPLACE THE PARTS DETECTED IN PROCEDURE 7 |
Replace the parts detected in Procedure 7 as the noise source.
| NEXT | |
| 9. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Check whether the noise problem has been successfully solved.
| NEXT | ||
| ||
| 10. EXPLAIN TO THE CUSTOMER THAT THE NOISE IS NORMAL |
Explain to the customer that the noise the customer mentioned is not abnormal.
- HINT:
- To help the customer understand, test driving another car with the customer may be helpful.
| NEXT | ||
| ||
