2014-2019 Hiace · Service Manual BODY

INSTALLATION

Removal / installation · Vehicles built Oct 2014 – Mar 2016

Versions by build date: Oct 2014 – Mar 2016 from Apr 2016


1. CLEAN VEHICLE BODY

  1. B073084
    Clean and shape the contact surface of the vehicle body.

    1. On the contact surface of the vehicle body, use a knife to cut away excess adhesive as shown in the illustration.

      HINT:
      Leave as much adhesive on the vehicle body as possible.

      NOTICE:
      Be careful not to damage the vehicle body.

    2. Clean the contact surface of the vehicle body with cleaner.

      HINT:
      Even if all the adhesive has been removed, clean the vehicle body.


2. INSTALL ROOF WINDOW FIX GLASS

  1. B114789E01
    Using a brush or sponge, apply Primer M to the exposed part of the vehicle body.

    NOTICE:
    1. Allow the Primer M to dry for 3 minutes or more.
    2. Do not apply Primer M to the adhesive.
    3. Throw away any leftover Primer M.
    4. Do not apply too much Primer M.

  1. Using a brush or sponge, apply Primer G to the contact surface of the roof window fix glass.

    B229170E01

    Specification:
    Area
    Measurement
    a
    14.8 mm (0.583 in.)
    b
    4.0 mm (0.157 in.)
    c
    8.0 mm (0.315 in.)

    HINT:
    If Primer G is applied to an area other than that which is specified, wipe off the primer with non-residue solvent before it dries.

    NOTICE:
    1. Allow the Primer G to dry for 3 minutes or more.
    2. Throw away any leftover Primer G.
    3. Do not apply too much Primer G.

  1. Apply adhesive to a new roof window fix glass.

    Adhesive:
    Toyota Genuine Windshield Glass Adhesive or equivalent


    1. B115241E01
      Cut off the tip of cartridge nozzle as shown in the illustration.

      Specification:
      Area
      Measurement
      a
      8.0 mm (0.315 in.)
      b
      12.0 mm (0.472 in.)

      HINT:
      After cutting off the tip, use all adhesive within the time written in the table below.

      Usage time frame:
      Temperature
      Usage Time Frame
      35°C (95°F)
      15 minutes
      20°C (68°F)
      1 hour 40 minutes
      5°C (41°F)
      8 hours

    2. Load the sealer gun with the cartridge.

    3. Apply adhesive to the roof window fix glass as shown in the illustration.

      B229171E01

      Specification:
      Area
      Measurement
      a
      14.8 mm (0.583 in.)
      b
      8.0 mm (0.315 in.)
      c
      12 mm (0.472 in.)

  1. Install the roof window fix glass to the vehicle body.

    1. Lightly press the front surface of the roof window fix glass to ensure that the roof window fix glass is securely fit to the vehicle body.

      NOTICE:
      1. Check that the spacers are attached to the vehicle body correctly.
      2. Check that the vehicle body and roof window fix glass have a small gap between them.

    2. Hold the roof window fix glass in place securely with protective tape or equivalent until the adhesive hardens.

      NOTICE:
      Do not drive the vehicle for the amount of time written in the table below.

      Minimum time:
      Temperature
      Minimum time prior to driving vehicle
      35°C (95°F)
      1 hour 30 minutes
      20°C (68°F)
      5 hours
      5°C (41°F)
      24 hours


3. CHECK FOR LEAKAGE AND REPAIR
  1. After the adhesive has hardened, apply water from the outside of the vehicle. Check that no water leaks into the cabin.

  1. If water leaks into the cabin, allow the water to dry and add adhesive.

  1. Remove the protective tape.


4. INSTALL ROOF HEADLINING GARNISH
  1. Attach the 18 clips to install the rear roof headlining garnish.

← REMOVAL (from Apr 2016)INSTALLATION (from Apr 2016) →