2014-2019 Hiace · Service Manual ENGINE

SYSTEM DESCRIPTION

Troubleshooting · Vehicles built from Oct 2014

This section should be used as a guide for troubleshooting when the turbocharger is suspected as the cause of a problem.

OUTLINE OF TURBOCHARGER FAILURE
  1. State of Turbocharger Failure Repair:
    It is well known that turbocharger malfunctions cause many symptoms as shown below. However, the mechanisms resulting in these symptoms that indicate turbocharger malfunctions are not well understood. As a result, many unnecessary turbocharger replacements and other repairs are being performed due to lack of knowledge about the turbocharger and turbocharger failure. Therefore, knowing the facts regarding turbocharger malfunctions is useful for making effective repairs and saving time.

  2. Turbocharger Failure Classification

    Symptom
    Symptom Description
    See page
    Noise
    Whistling noise
    Continuous high pitch noise proportional to engine speed
    1. "NOISE" listed below
    2. Flowchart "Turbocharger Noise" (Click here)
    Whining noise
    Relatively low pitch noise compared to whistling noise
    Oil leak
    External oil leak
    Oil leak on surface of turbocharger visible from outside of turbocharger
    1. "OIL LEAK AND WHITE SMOKE" listed below
    2. Flowchart "Turbocharger Oil Leak and White Smoke" (Click here)
    Internal oil leak
    Oil leak from inside of bearing housing to inside of either compressor housing or turbine housing through seal ring
    White smoke
    Oil smoke
    Oil smoke is emitted from exhaust pipe
    Unburned fuel smoke
    Unburned fuel smoke is emitted from exhaust pipe
    Black smoke
    Black smoke is emitted from exhaust pipe
    1. "BLACK SMOKE" listed below
    2. Flowchart "Black Smoke Emitted" (Click here)
    Lack of power or hesitation
    Vehicle does not reach target speed
    1. "LACK OF POWER AND HESITATION" listed below
    2. Flowchart "Lack of Power or Hesitation" (Click here)
    Poor acceleration
    Shock during acceleration

    HINT:
    This table shows only typical problems related to the turbocharger.


NOISE
Description 
Probable Cause
Probable Failed Component
Turbine shaft imbalance
Turbocharger
Leakage from intake line
Intake line
Gear noise
(Mistaken for turbocharger noise)
  1. Gear inside engine
  2. Transmission gear
  3. Vacuum pump gear

HINT:
It is easy to confirm whether the turbocharger is the cause of the noise or not, and confirming this before inspecting the turbocharger or removing it from the engine is an effective way to reduce troubleshooting time.

  1. Disconnect the actuator hose from the compressor housing.

  2. Stop up the compressor housing side tube with a hose clip or equivalent.

  3. A148172
    Using SST, apply pressure to the actuator to open the waste gate valve.
    SST
    09992-00242  

    Valve opening pressure:
    Specified pressure* (See attached table below)

    NOTICE:
    Never apply more than predetermined maximum pressure* to the actuator.


    HINT:
    *: Valve opening pressure and predetermined maximum pressure above differ according to the vehicle model and turbocharger. For the specifications, see attached table below.
    Specifications: 
    Engine Type
    Turbocharger Sub-assembly
    (Part No.)
    Valve Opening Pressure
    (kPa: Gauge Pressure)
    Maximum Pressure
    (kPa: Gauge Pressure)
    Reference:
    Rod Stroke
    (mm)
    2KD-FTV
    17201-30070
    130
    147.8
    0.89 to 1.74
    17201-30080
    119
    136
    0.98 to 1.91

  4. Check that the actuator rod moves and that the waste gate valve opens.

  5. Start the engine and allow it to idle.

  6. Rev the engine up several times, depressing the accelerator pedal.

    NOTICE:
    Do not accelerate the engine while sufficient pressure is not applied to the actuator. The boost pressure (turbocharged air pressure) may exceed the prescribed booster pressure limit and the engine may be damaged due to overboost.

  7. Check whether the noise is reduced or not compared with the noise under the original conditions.

    Result 
    Result
    Cause of Noise
    The noise is reduced (or disappears)
    Turbocharger
    The noise does not change
    Not turbocharger (other parts)

  8. Reconnect the actuator hose to the compressor housing.

    HINT:
    Refer to the flowchart "Turbocharger Noise" (Click here).


OIL LEAK AND WHITE SMOKE
Description 
Oil Leak Type
Description
Main Trouble Area
Internal oil leak
(White smoke)
  1. Oil leak from bearing housing to either compressor housing (intake side) or turbine housing (exhaust side) through seal rings.
  2. This type of oil leak is not visible from outside of turbocharger.
  3. If oil leak occurs from turbine side seal, large amount of white smoke is emitted from exhaust pipe.
  1. Compressor side seal ring
  2. Turbine side seal ring
  3. Clogging of oil drain
  4. Shaft breakage
  5. Shaft or bearing seizure
  6. Compressor impeller damage
External oil leak
  1. Oil leak from inside of turbocharger to outside of turbocharger.
  2. Includes oil leaks visible from outside of turbocharger.
  1. FIPG sealing part
  2. Oil pipe flange
  3. Oil pipe union
  4. Hose connection of intake pipe
A229650E01
Text in Illustration 
*A
Waste Gate Type Turbocharger
-
-
*1
Compressor Housing
*2
Seal Ring
*3
Compressor Inlet
*4
Compressor Impeller
*5
Bearing Housing
*6
Turbine Shaft
*7
Oil Drain (Outlet)
*8
FIPG Sealing Part
*9
Turbine Housing
*10
Turbine Wheel
*a
Internal oil leak to compressor housing
*b
Internal oil leak to turbine housing

HINT:
  1. Above illustration is an example.
  2. When there is an internal oil leak, white smoke is emitted from the exhaust pipe and oil is consumed excessively. However, the cause of white smoke or excessive oil consumption can vary. Therefore, do not assume that the turbocharger is the cause of the failure when there is white smoke emission or excessive oil consumption.
  3. When there is an external oil leak, the sources of the oil leak are limited to the points mentioned in the table above. If oil leaks from a FIPG sealing part, replace the turbocharger. If oil leaks from an oil pipe flange or a hose connection, do not replace the turbocharger, but confirm and repair the flange or hose.
  4. Refer to the flowchart "Turbocharger Oil Leak and White Smoke" (Click here).


BLACK SMOKE
  1. Malfunctions are classified into 2 types as shown below.

    Description 
    Malfunction
    Main Fault
    Intake air volume shortage
    Insufficient mass air flow due to, for example, excessively low boost pressure, which results in fuel injection volume being relatively excessive with respect to mass air flow.
    Excessive injection volume
    Excessive injection volume or incorrect injection timing due to fuel system trouble.

  2. Main Components Related to Black Smoke:

    Possible Faulty Component
    Main Fault
    Turbocharger
    Abnormally low boost pressure
    Intake system
    Leakage between turbocharger and intake manifold
    Fuel system
    1. Excessive fuel injection volume
    2. Incorrect fuel injection timing
    EGR valve
    Stuck or does not close completely
    Diesel throttle
    Stuck or does not move smoothly

    HINT:
    The components listed above are only the main ones. Not all the components potentially related to black smoke are listed. For details regarding the troubleshooting of black smoke, refer to the flowchart "Black Smoke Emitted" (Click here).

  3. Relation between Turbocharger and Black Smoke:
    If the boost pressure is lower than normal due to a turbocharger failure, black smoke may occur due to a lack of mass air flow. However, abnormally low boost pressure can be caused by the failure of various components such as intake lines, the EGR valve, etc. Therefore, do not assume that the turbocharger is the cause of abnormally low boost pressure, but check all the components possibly related to abnormally low boost pressure. Components related to abnormal boost pressure are shown in a chart listed in the On-vehicle Inspection for Intake System (Click here). For simple and effective troubleshooting, refer to the chart before starting troubleshooting.


LACK OF POWER AND HESITATION
  1. Malfunctions are classified into 2 types as shown below.

    Description 
    Malfunction
    Main Fault
    Intake air volume shortage
    Insufficient mass air flow due to, for example, excessively low boost pressure, which results in fuel injection volume being restricted.
    Abnormal injection volume
    Abnormal injection volume or timing due to fuel system trouble.

  2. Main Components Related to Lack of Power and Hesitation:

    Possible Faulty Component
    Main Fault
    Turbocharger
    1. Abnormal boost pressure
    2. Waste gate valve does not move smoothly (stuck open)
    Intake system
    1. Leakage between turbocharger and intake manifold
    2. Clogging or blockage of intake line
    Fuel system
    1. Abnormal injection volume
    2. Incorrect fuel injection timing
    EGR valve
    Stuck or does not close completely
    Diesel throttle
    Stuck or does not move smoothly
    Exhaust system
    Clogging of exhaust line

    HINT:
    1. The components listed above are only the main ones. Not all the components potentially related to lack of power and hesitation are listed. For details regarding the troubleshooting of lack of power and hesitation, refer to the flowchart "Lack of Power and Hesitation" (Click here).
    2. If obvious malfunction (lack of power) has not been reproduced, perform test driving another vehicle, which is the same model and has the same engine, and compare the engine conditions and performance. If a great difference does not present in engine performance, explain to the customer that lack of power the customer mentioned is not abnormal.

  3. Relation between Turbocharger and Abnormal Boost Pressure:
    If the boost pressure is lower than normal due to a turbocharger failure, lack of power could occur due to an intake air volume shortage. However, abnormal boost pressure can be caused by the failure of various components such as intake lines, the EGR valve, etc. Therefore, do not assume that the turbocharger is the cause of abnormal boost pressure, but check all the components possibly related to abnormal boost pressure. Components related to abnormal boost pressure are shown in a chart listed in the On-vehicle Inspection for Intake System (Click here). For simple and effective troubleshooting, refer to the chart before starting troubleshooting.


MIL TURNS ON
If a DTC related to a turbocharger malfunction is stored, refer to the troubleshooting section for each DTC (Click here).

BRIEF OUTLINE OF TURBOCHARGER OPERATION AND CONSTRUCTION
  1. A turbocharger is a component used to supply a larger air volume to the cylinders by recovering exhaust gas energy using a turbine coaxially connected to a compressor.

  2. Principle of Turbocharging:
    Boost pressure is proportional to turbocharger speed, because the intake air is accelerated by centrifugal force generated by the rotation of the compressor and the increased kinetic energy, i.e. the velocity of the intake air, is converted to pressure energy by the diffuser located around the outlet of the compressor impeller. The compressor is driven by the turbine connected coaxially by the turbine shaft. The turbine is driven by exhaust gas energy. Therefore, when the turbocharger begins boosting the intake air, a larger air volume is supplied to the cylinders and more fuel can be injected. As a result, more exhaust energy will be available and the turbocharger boost increases.
    A227153E01

    Text in Illustration 
    *1
    Compressor
    *2
    Turbine
    *3
    Air Cleaner
    *4
    Exhaust Manifold
    *5
    Intake Manifold
    *6
    Intercooler
    *7
    Diffuser
    *8
    Compressor
    *a
    See HINT below
    *b
    Intake air flow

    HINT:
    1. *a: If sufficient exhaust gas energy is not available, the turbocharger cannot generate the required boost pressure even when the turbocharger does not have a malfunction.
    2. Considering the fact that the turbocharger is driven by exhaust gas energy, if sufficient exhaust gas is not available due to abnormal injection volume, etc., the required boost pressure will not be available even when the turbocharger does not have a malfunction. Therefore, when boost pressure is abnormally low, checking all the related components using the correct troubleshooting procedure is necessary for simple and effective repair.

  3. Boost Pressure Control:
    When the boost pressure (turbocharged air pressure) exceeds the prescribed air pressure, the flow of exhaust gas bypasses the turbine, controlling turbine wheel revolutions and boost pressure. This bypass valve which controls the quantity of exhaust gas flowing to the turbine is called the waste gate valve. When the boost pressure exceeds the prescribed pressure, the actuator operates, the waste gate valve opens and part of the exhaust gas bypasses the turbine. This causes a drop in the turbine revolution rate and controls the boost pressure within the prescribed limits.

    HINT:
    If the waste gate valve becomes stuck open, the necessary boost pressure will not be available. If the waste gate valve becomes stuck closed, overboost will occur.

  4. Mechanical Construction of Turbocharger:
    A230521E01

    Text in Illustration 
    V100135
    Exhaust Gas Flow
    V100136
    Intake Air Flow
    *A
    Waste Gate Type Turbocharger
    -
    -
    *1
    Waste Gate Actuator
    *2
    Actuating Rod
    *3
    Bearing Housing
    *4
    Turbine Shaft
    *5
    Radial Bearing
    *6
    Turbine Side Seal Ring
    *7
    Turbine Housing
    *8
    Turbine Wheel
    *9
    Thrust Bearing
    *10
    Compressor Side Seal Ring
    *11
    Compressor Housing
    *12
    Compressor Impeller
    *13
    Radial Bearing
    *14
    Waste Gate Actuator
    *15
    Oil Drain
    -
    -
    *a
    See HINT below
    *b
    See HINT below
    *c
    See HINT below
    -
    -

    HINT:
    1. Above illustration is an example.
    2. *a: The clearances of the radial bearing and thrust bearing are on the order of 100 μm, and for the accurate measurement of these clearances, an accurate process and accurate tools are essential.
    3. *b: A certain amount of oil mist from PCV gas is contained in the intake air. Therefore, a certain amount of oil at the inlet of the compressor is normal, and is not an oil leak.
    4. *c: The seal rings are C-shaped rings just like piston rings, and have a gap. Therefore, complete sealing is impossible by the seal rings alone. The oil is sealed in with the aid of the boost pressure in the compressor housing, and the exhaust gas pressure in the turbine housing. These pressures prevent oil from exiting the bearing housing through the gap of the seal rings. Therefore, if the turbine shaft is inclined from the horizontal, oil may flow out through the gap of a seal ring. This should not be interpreted as an oil leak due to seal ring failure.

← COMPONENTS (from Oct 2014)REMOVAL (from Oct 2014) →