B2779 Engine Starter Communication Malfunction
Diagnostic trouble codes · Vehicles built from Oct 2014
DESCRIPTION
If communication between the remote engine start ECU and certification ECU (smart key ECU assembly) cannot be performed even if a remote start operation is performed to try changing the power source mode to on (IG) or start the engine, this DTC is stored.When the remote engine start ECU does not respond to the certification ECU (smart key ECU assembly), this DTC is stored. When communication with the remote engine start ECU is established, this DTC is cleared.
| DTC Code |
DTC Detection Condition |
Trouble Area |
DTC Output Confirmation Operation |
| B2779 |
One of the following conditions is met (1 trip detection logic*):
|
|
A remote start operation is performed. |
- *: Only output while a malfunction is present.
| Vehicle Condition when Malfunction Detected |
Fail-safe Operation when Malfunction Detected |
| Engine does not start with remote start operation |
Engine cannot be started by remote start operation only |
| DTC Code |
Data List and Active Test |
| B2779 |
|
INSPECTION PROCEDURE
- NOTICE:
- Inspect the fuses for circuits related to this system before performing the following inspection procedure.
- Before performing the inspection, check that DTC U0142 is not output.
- Before replacing the certification ECU (smart key ECU assembly), refer to the Service Bulletin.
- After performing repair, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.
- Inspect the fuses for circuits related to this system before performing the following inspection procedure.
- HINT:
- In this repair manual, only the terminal numbers used for inspection between the instrument panel junction block assembly (body ECU) and option connector are listed.
| 1. READ VALUE USING GTS (WIRELESS C CODE) |
Turn the engine switch off.
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Entry & Start / Data List.
According to the display on the GTS, read the Data List.
Entry & Start (Certification ECU [Smart Key ECU Assembly]) Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Wireless C Code
Registration status between remote engine start ECU and certification ECU (smart key ECU assembly) / No Regd or Regd
No Regd: ID not registered between remote engine start ECU and certification ECU (smart key ECU assembly)
Regd: ID registered between remote engine start ECU and certification ECU (smart key ECU assembly)
Problems may be caused by the following: - DTC B2779 is stored.
- Remote engine start ECU registration has not been performed.
- Malfunctions in the certification ECU (smart key ECU assembly) or remote engine start ECU.
- OK:
- "Regd" appears on the screen.
Result Result
Proceed to
"No Regd" appears on the screen
A
"Regd" appears on the screen
B
- DTC B2779 is stored.
|
|
||||
| A | |
| 2. REGISTER REMOTE START ID |
Register the remote start ID.
| NEXT | |
| 3. CHECK REMOTE START OPERATION |
Check that the engine can be started using remote start operation.
- OK:
- Engine can be started using remote start operation.
|
|
||||
| OK | ||
| ||
| 4. CHECK REMOTE ENGINE START ECU |
Temporarily replace the remote engine start ECU with a new one.
Register the remote start ID.
Check that the engine can be started using remote start operation.
- OK:
- Engine can be started using remote start operation.
|
|
||||
| OK | ||
| ||
| 5. CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (BODY COMPUTER) |
Temporarily replace the instrument panel junction block assembly (body computer) with a new one.
Check that the engine can be started using remote start operation.
- OK:
- Engine can be started using remote start operation.
|
|
||||
| OK | ||
| ||
