2014-2019 Hiace · Service Manual ENGINE

INSTALLATION

Removal / installation · Vehicles built Apr 2016 – Dec 2016

Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Mar 2016 Apr 2016 – Dec 2016 from Jan 2017


1. INSTALL EXHAUST FUEL ADDITION INJECTOR ASSEMBLY

NOTICE:
If there is foreign matter on the installation surface of the exhaust fuel addition injector assembly, be sure to clean the exhaust fuel addition injector assembly before installation.

  1. Install a new E-ring, a new O-ring and 3 new backup rings to the exhaust fuel addition injector assembly.

    A239824E05

    Text in Illustration 
    *1
    No. 1 Backup Ring
    *2
    No. 2 Backup Ring
    *3
    No. 3 Backup Ring
    *4
    O-Ring
    *5
    E-Ring
    -
    -
    *a
    CORRECT
    *b
    INCORRECT
    *c
    Overlapped
    *d
    Normal
    *e
    Stretched
    -
    -

    NOTICE:
    1. Check that there is no foreign matter or damaged areas in the injector O-ring groove.
    2. Check that the No. 1 and No. 2 backup rings are installed in the correct direction.
    3. Make sure that the backup rings and O-ring are installed in the correct order.
    4. Check that the alignment openings of the backup rings are not stretched and that the ends of the backup rings are not overlapped as shown in the illustration.
    5. After installing the O-ring, check that it is not contaminated with foreign matter and is not damaged.

  1. Install a new gasket and the No. 1 injector holder with the 3 bolts.

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }

  1. Install a new injection nozzle seat and the exhaust fuel addition injector assembly.

  1. Using a T40 "TORX" socket wrench, install the No. 1 nozzle holder clamp with the screw.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Temporarily install the No. 2 injector holder to the No. 1 injector holder with the 2 bolts.

  1. Tighten the No. 2 injector holder with the 2 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }


2. INSTALL TURBINE OUTLET ELBOW
(Click here)

3. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


4. ADD ENGINE COOLANT
  1. Firmly tighten the drain plugs.

  1. Fill the radiator reservoir assembly with engine coolant to the top of the inlet.

    Standard Capacity:
    Item
    Specified Condition
    w/o Heater
    13.2 liters (13.9 US qts, 11.6 Imp. qts)
    w/ Front Heater
    14.2 liters (15.0 US qts, 12.5 Imp. qts)
    w/ Front and Rear Heaters
    16.2 liters (17.1 US qts, 14.3 Imp. qts)

    NOTICE:
    Do not substitute plain water for engine coolant.

    HINT:
    1. Use of improper coolants may damage the engine cooling system.
    2. Use only Toyota Super Long Life Coolant or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, and non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).

  1. Loosen the bleeder plug of the outlet housing.

  1. When air is bled and the engine coolant drains out, firmly tighten the bleeder plug.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. A142533
    Add engine coolant up to the B line mark in the radiator reservoir assembly and install the radiator reservoir cap sub-assembly.

  1. Warm up the engine until the thermostat opens.

    1. While the thermostat is open, circulate the engine coolant for several minutes.

      HINT:
      The thermostat open timing can be confirmed by pressing the No. 3 radiator hose by hand, and checking when the engine coolant starts to flow inside the hose.

  1. A142532
    After the engine cools down, check that the engine coolant level is between the LOW and FULL level marks.


5. INSPECT FOR COOLANT LEAK

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Hot, pressurized engine coolant and steam may be released and cause serious burns.

  1. Fill the radiator with coolant and attach a radiator cap tester to the radiator.

  1. Warm up the engine.

  1. Using a radiator cap tester, increase the pressure inside the radiator to 137 kPa (1.4 kgf/cm2, 19.9 psi), and check that the pressure does not drop.

    HINT:
    If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and cylinder head.


6. INSPECT FOR FUEL LEAK
  1. Perform the Active Test.

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Engine and ECT / Active Test.

    5. Perform the Active Test.

      Tester Display
      Test Part
      Control Range
      Diagnostic Notes
      Test the Fuel Leak
      Pressurize common rail interior and check for fuel leaks
      Stop/Start
      1. Fuel pressure inside common rail increased to specified value and engine speed increased to 2000 rpm when Active Test is performed
      2. Above conditions preserved while Active Test is being performed

← INSTALLATION (Jan 2015 – Mar 2016)INSTALLATION (from Jan 2017) →