2014-2019 Hiace · Service Manual BODY ELECTRICAL

DATA LIST / ACTIVE TEST

System information · Vehicles built from Oct 2014


DATA LIST

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

HINT:
  1. Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
  2. When using the GTS with the vehicle engine switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

  1. Connect the GTS to the DLC3.

  2. Turn the engine switch on (IG).

  3. Turn the GTS on.

  4. Enter the following menus: Body Electrical / Entry&Start, Power Source Control or Combination Meter / Data List.

  5. According to the display on the GTS, read the Data List.

    Entry&Start 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    D-Door Trigger Switch
    Driver door trigger switch / ON or OFF
    ON: Driver door trigger switch pressed
    OFF: Driver door trigger switch not pressed
    1. Displays whether the trigger switch is on or off (even if the trigger switch is pressed and contact is maintained, "ON" is displayed only momentarily).
    2. Use this Data List item to help determine if there is a trigger switch malfunction when the entry lock function does not operate.
    P-Door Trigger Switch
    Front passenger door trigger switch / ON or OFF
    ON: Front passenger door trigger switch pressed
    OFF: Front passenger door trigger switch not pressed
    1. Displays whether the trigger switch is on or off (even if the trigger switch is pressed and contact is maintained, "ON" is displayed only momentarily).
    2. Use this Data List item to help determine if there is a trigger switch malfunction when the entry lock function does not operate.
    Tr/B-Door Unlock SW
    Back door trigger switch / ON or OFF
    ON: Back door trigger switch pushed
    OFF: Back door trigger switch not pushed
    1. Displays whether the back door opening switch assembly is on or off.
    2. Use this Data List item to help determine if there is a switch malfunction when the back compartment door open function does not operate.
    Unmatched Vehicle- ID
    Key No. (incorrect or correct) / Yes or No
    Yes: Communication malfunction
    No: Communication normal
    The vehicle ID registered in the vehicle and the vehicle ID registered in the electrical key transmitter sub-assembly are different (if a key from another vehicle is brought into the vehicle exterior detection area while the doors are locked, "Yes" is displayed for "Unmatched Vehicle- ID" in the Data List).
    Other potential causes:
    1. An electrical key transmitter sub-assembly from a different vehicle is being used.
    2. A communication error due to electric wave interference.
    3. The electrical key transmitter sub-assembly or certification ECU (smart key ECU assembly) is malfunctioning.
    No Response
    Communication response / Yes or No
    Yes: Communication malfunction
    No: Communication normal
    The vehicle IDs registered in the vehicle and electrical key transmitter sub-assembly match, but there is no response from the electrical key transmitter sub-assembly. (If the electrical key transmitter sub-assembly is not in the detection area or the transmitter battery is depleted resulting in a matching code not being detected when a lock switch or the engine switch is pressed, etc., "Yes" is displayed for "No Response" in the Data List. If there is wave interference in the LF band that the vehicle uses for transmission or the RF band that the electrical key transmitter sub-assembly uses for transmission, "Yes" may be displayed for "No Response" in the Data List).
    Other potential causes:
    1. An electrical key transmitter sub-assembly from a different vehicle is being used.
    2. The electrical key transmitter sub-assembly or certification ECU (smart key ECU assembly) is malfunctioning.
    Unmatch Code or Form
    Code format (incorrect or correct) / Yes or No
    Yes: Communication malfunction
    No: Communication normal
    There is an error in the data sent from the electrical key transmitter sub-assembly (if there is wave interference in the RF band that the electrical key transmitter sub-assembly uses for transmission, "Yes" may be displayed for "Unmatch Code or Form", "No Response", "ID Code Difference(Resp)" and "C Code Difference" in the Data List).
    Other potential causes:
    1. An electrical key transmitter sub-assembly from a different manufacturer is being used.
    2. The electrical key transmitter sub-assembly or certification ECU (smart key ECU assembly) is malfunctioning.
    Key Low Battery
    Transmitter battery depleted / Yes or No
    Yes: Transmitter battery depleted
    No: Transmitter battery not depleted
    The electrical key transmitter sub-assembly sends voltage information to the certification ECU (smart key ECU assembly) when it is transmitting. The certification ECU (smart key ECU assembly) displays "Yes" for the "Key Low Battery" item of the Data List when this voltage information indicates 2.1 V or less. This Data List item should be checked when the electrical key transmitter sub-assembly is at room temperature (example: at -20°C (-4°F), "Yes" may be displayed even if the transmitter battery is new).
    # Codes
    Number of trouble codes / Min: 0, Max: 255
    Number of stored DTCs displayed
    -
    ID Code Difference(Resp)
    ID code (incorrect or correct) / Yes or No
    Yes: Communication malfunction
    No: Communication normal
    The ID code registered in the vehicle and the ID code registered in the electrical key transmitter sub-assembly are different (if there is wave interference in the RF band that the electrical key transmitter sub-assembly uses for transmission, "Yes" may be displayed for "Unmatch Code or Form", "No Response", "ID Code Difference[Resp]" and "C Code Difference" in the Data List).
    Other potential causes:
    1. An electrical key transmitter sub-assembly from a different vehicle is being used.
    2. The electrical key transmitter sub-assembly or certification ECU (smart key ECU assembly) is malfunctioning.
    C Code Difference
    Challenge code (incorrect or correct) / Yes or No
    Yes: Communication malfunction
    No: Communication normal
    The electrical key transmitter sub-assembly sends a response code in response to the challenge code from the vehicle, but the response code is incorrect (if there is wave interference in the RF band that the electrical key transmitter sub-assembly uses for transmission, "Yes" may be displayed for "Unmatch Code or Form", "No Response", "ID Code Difference[Resp]" and "C Code Difference" in the Data List).
    Other potential causes:
    1. The electrical key transmitter sub-assembly or certification ECU (smart key ECU assembly) is malfunctioning.
    ID Code Difference
    Wireless ID code (incorrect or correct) / Yes or No
    Yes: Communication malfunction
    No: Communication normal
    The ID code registered in the vehicle and the ID code registered in the electrical key transmitter sub-assembly are different. (If a wireless ID other than those for any of the registered electrical key transmitter sub-assemblies is detected, "Yes" is displayed for "ID Code Difference" in the Data List. If a wireless signal from the electrical key transmitter sub-assembly of another vehicle is detected, "Yes" is displayed for "ID Code Difference[Resp]" in the Data List).
    Other potential causes:
    1. An electrical key transmitter sub-assembly from a different vehicle is being used.
    2. A communication error due to external noise (RF).
    3. The electrical key transmitter sub-assembly or certification ECU (smart key ECU assembly) is malfunctioning.
    Immobilizer when IG=ON
    Immobiliser system status when power source mode on (IG) / SET or UNSET
    SET: Immobiliser system set (engine switch off)
    UNSET: Immobiliser system unset (engine switch on [ACC] or on [IG])
    -
    Immobiliser
    Immobiliser system status determined by certification ECU / Set or Unset
    Set: Immobiliser set (engine start prohibited) (engine switch off)
    Unset: Immobiliser unset (engine start permitted) (engine switch on [ACC] or on [IG])
    When the immobiliser system does not change to the unset state, this item can be used to determine if the cause is the certification ECU.
    Different Rolling Code
    Rolling code (incorrect or correct) / Yes or No
    Yes: Communication malfunction
    No: Communication normal
    The rolling code registered in the vehicle and the rolling code registered in the electrical key transmitter sub-assembly are different. Other potential causes:
    1. An electrical key transmitter sub-assembly switch is pressed 100 times or more in a location where the electric waves cannot reach the vehicle.
    2. A communication error due to external noise (RF).
    3. The electrical key transmitter sub-assembly or certification ECU (smart key ECU assembly) is malfunctioning.
    Auto Entry Cancel SW
    Entry cancel function setting / ON or OFF
    Mode status displayed
    ON: Smart entry and start system canceled
    OFF: Smart entry and start system not canceled
    The default setting for the entry cancel function is OFF. If the customer requests that the smart entry and start system functions (locking and unlocking the doors while carrying the electrical key transmitter sub-assembly, etc.) be canceled, the setting can be changed through the customize function.
    S Code Check
    S code verification result / OK or NG
    OK: S code verification result normal
    NG: S code verification result abnormal
    Problems may be caused by the following:
    1. Registration has not been performed for the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU).
    2. Malfunctions in the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU).
    L Code Check
    L code verification result / OK or NG
    OK: L code verification result normal
    NG: L code verification result abnormal
    Problems may be caused by the following:
    1. Registration has not been performed for the ID code box (immobiliser code ECU) or steering lock ECU (steering lock actuator assembly).
    2. Malfunctions in the ID code box (immobiliser code ECU) or steering lock ECU (steering lock actuator assembly).
    Unlock Request Receive
    Status of steering unlock command from certification ECU (smart key ECU assembly) / OK or NG
    OK: Certification ECU (smart key ECU assembly) sends steering unlock command (within 10 seconds of engine switch turned on [ACC] or on [IG], or of engine start operation performed)
    NG: Certification ECU (smart key ECU assembly) does not send steering unlock command (engine switch not turned on [ACC] or on [IG], and engine start operation not performed)
    -
    Lock Request Receive
    Status of steering lock command from certification ECU (smart key ECU assembly) / OK or NG
    OK: Certification ECU (smart key ECU assembly) sends steering lock command (within 10 seconds of any door opened with shift lever in P and engine switch off)
    NG: Certification ECU (smart key ECU assembly) does not send steering lock command (no door opened with shift lever in P and engine switch off)
    -
    S Code Check(Past)
    S code verification result (past) / OK or NG (Past)
    OK: Verification result normal
    NG (Past): Verification result abnormal (past)
    -
    L Code Check(Past)
    L code verification result (past) / OK or NG (Past)
    OK: Verification confirmed (past)
    NG (Past): Verification not confirmed (past)
    -
    Steering Lock
    State of whether steering lock ECU (steering lock actuator assembly) has determined steering is locked / Set or Unset
    Set: Steering locked
    Unset: Steering unlocked
    -
    Steering Unlock
    State of whether steering lock ECU (steering lock actuator assembly) determined steering is unlocked / Set or Unset
    Set: Steering unlocked
    Unset: Steering locked
    -
    Power Source Control 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Shift P Signal
    Shift position P / ON or OFF
    ON: Shift lever in P
    OFF: Shift lever not in P
    1. Use this item to determine if the shift position switch is malfunctioning.
    2. The engine cannot be started when this item is OFF.
    Steering Unlock Switch
    State of steering unlock sensor signal output from steering lock actuator assembly / ON or OFF
    ON: Steering unlocked
    OFF: Steering locked
    1. When the shift lever is in P and the engine switch is off, if any door is opened then closed, the steering is locked.
    2. When the key is inside the vehicle and the engine switch is turned on (ACC) or on (IG), the steering unlocks.
    3. The engine cannot be started when the steering unlock signal is off.
    Stop Light Switch1
    State of brake pedal / ON or OFF
    ON: Brake pedal depressed
    OFF: Brake pedal released
    1. Use this item to determine whether the stop light switch is malfunctioning.
    2. The engine cannot be started when this item is OFF.
    3. When this item is malfunctioning, the engine can be started by pressing and holding the engine switch for a certain period of time.
    Start Switch1
    Engine switch 1 status / ON or OFF
    ON: Engine switch pressed
    OFF: Engine switch not pressed
    1. If the engine switch is pressed for a short time, the display may not change.
    2. Use this item to determine whether the engine switch input signal is malfunctioning.
    Start Switch2
    Engine switch 2 status / ON or OFF
    ON: Engine switch pressed
    OFF: Engine switch not pressed
    1. Backup for engine switch 1. However, when the engine switch is pressed and held, the control functions only when both engine switch 1 and 2 are normal.
    2. Behaves the same way as engine switch 1.
    Vehicle Speed Signal
    Vehicle being driven or stopped / Stop or Run
    Stop: Vehicle stopped
    Run: Vehicle being driven at 5 km/h (3 mph) or more
    -
    Power Supply Condition
    Power supply state / ST ON, ALL OFF, IG ON or ACC ON
    All OFF: Engine switch off (ACC and IG)
    ACC ON: Engine switch on (ACC)
    IG ON: Engine switch on (IG)
    ST ON: Sending engine start request signal
    -
    Combination Meter 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Vehicle Speed Meter
    Vehicle speed / Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph)
    Almost the same as actual vehicle speed
    -


ACTIVE TEST

HINT:
Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Connect the GTS to the DLC3.

  2. Turn the engine switch on (IG).

  3. Turn the GTS on.

  4. Enter the following menus: Body Electrical / Entry&Start / Active Test.

  5. According to the display on the GTS, perform the Active Test.

    Entry&Start 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Overhead Tuner Power Supply ON
    Door control receiver
    OFF/ON
    -
    Power/Engine SW Light
    Engine switch light
    OFF/ON
    When performing this Active Test, make sure the following condition is met:
    1. The engine switch illumination is off (15 seconds or more have elapsed since it turned from on to off) and the engine switch is on (ACC) or on (IG), or the engine is running.
    Multi Channel SW
    Door control receiver
    CH1/CH2
    -
    Wireless Buzzer Operation
    Wireless door lock buzzer
    OFF/ON
    -

← DTC CHECK / CLEAR (from Oct 2014)DIAGNOSTIC TROUBLE CODE CHART (Oct 2014 – Dec 2014) →