2014-2019 Hiace · Service Manual BODY ELECTRICAL

CUSTOMIZE PARAMETERS

Removal / installation · Vehicles built from Oct 2014


1. CUSTOMIZE METER / GAUGE SYSTEM
  1. Customizing with the GTS

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Customize Setting / Combination Meter / Warning or Display.

    5. Select the setting by referring to the table below.

      Warning 
      Display
      Default
      Content
      Setting
      Relevant ECU
      Driver Side Seatbelt Warning Buzzer*
      ON
      Function to turn on/off the seat belt warning buzzer
      ON or OFF
      Combination meter assembly
      Front Passenger Side Seatbelt Warning Buzzer*
      ON
      Function to turn on/off the seat belt warning buzzer
      ON or OFF
      Combination meter assembly
      Lane Change Flashing Times Setting
      3
      Function to change the lane change flashing time
      OFF, 3, 5 or 7
      Combination meter assembly
      Flasher Sound Tone Setting
      Tone 3
      Function to change the flasher sound tone
      Tone 1, Tone 2 or Tone 3
      Combination meter assembly
      1. *: This setting is only valid for the buzzer which sounds at 20 km/h (12 mph) or more
      Display 
      Display
      Default
      Content
      Setting
      Relevant ECU
      ECO Drive Indicator Zone
      ON
      Function to turn on/off the eco driving indicator zone display
      ON or OFF
      Combination meter assembly
      ODO Display Time After IG OFF Setting
      30 s
      Function to change the odometer display time
      30 s, 60 s, 600 s or OFF
      Combination meter assembly

  1. Customizing with the combination meter assembly (for Dot Display Type)

    1. Turn the ignition switch to ON.

    2. Enter the following menus: SETTINGS.

    3. Select the setting by referring to the table below.

      SETTINGS 
      Display
      Default
      Content
      Setting
      Relevant ECU
      LANGUAGE
      ENGLISH
      Function to change the multi-information display language
      ENGLISH or Chinese
      Combination meter assembly
      UNITS
      L/100km
      Function to change the multi-information display unit
      km/L or L/100km
      Combination meter assembly
      ECO INDICATOR
      ON
      Function to turn on/off the eco driving indicator light
      ON or OFF
      Combination meter assembly

  1. Customizing with the combination meter assembly (for Segment Display Type)

    1. Turn the ignition switch to ON.

    2. Display the odometer screen.

    3. Press and hold the ODO/TRIP switch for 5 seconds or more to display the settings screen.

    4. After selecting "Eco On" or "EcoOFF", press and hold the ODO/TRIP switch for 2 seconds or more to exit the settings screen.

  1. Inspect T-BELT mode display (Engine Type Diesel)

    1. Turn the ignition switch to ON.

    2. Turn the ODO/TRIP display screen to "TRIP B", and turn the ignition switch off.

    3. While pressing the ODO/TRIP change switch, turn the ignition switch to ON to blink the T-BELT warning light, and then continue pressing the switch for 5 seconds or more.

    4. Release the ODO/TRIP switch, then press the ODO/TRIP switch again within 5 seconds.

    5. Transfer to the T-BELT mode, and the following initial setting value is displayed.
      km: 15 (0,000 km) or 9 (0,000 mile)

      HINT:
      If the meter has been replaced before, the displayed value might not be the same as the initial setting value.

  1. Rewriting replacement setting value (Engine Type Diesel)

    1. Press the ODO/TRIP switch and rewrite the replacement setting value.

      Condition
      Setting value
      When a belt is replaced
      km: 15 (0,000 km)
      mile: 9 (0,000 mile)
      When a meter is replaced
      km: [15 (0,000 km)] - (Mileage when the meter is replaced)
      mile: [9 (0,000 mile)] - (Mileage when the meter is replaced)

      HINT:
      Every press of the ODO/TRIP switch adds 10,000 km or 10,000 mile and the meter returns to 10,000 km or 10,000 mile when 200,000 km or 200,000 mile is reached. If switch operation is not performed within 30 seconds, the setting value will not be changed. The display screen turns to "TRIP B", and the mode returns to the normal mode.

  1. T-BELT mode completion (Engine Type Diesel)

    NOTICE:
    If the T-BELT mode is completed, even though belt replacement or meter replacement has not been performed, the T-BELT warning is reset.


    1. After setting the replacement setting value, hold the ODO/TRIP switch on for more than 5 seconds, then release the ODO/TRIP switch.

    2. Check that the display is changed to "TRIP B" and the warning light goes off.

← HOW TO PROCEED WITH TROUBLESHOOTING (from Oct 2014)PROBLEM SYMPTOMS TABLE (Oct 2014 – Dec 2014) →