2014-2019 Hiace · Service Manual HEATER & AIR CONDITIONING SYSTEM

INSPECTION

Inspection · Vehicles built from Oct 2014


INSPECT HEATER CONTROL KNOB (w/ Air Conditioning System)

  1. E103714E02
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance (for 1KD-FTV, 2KD-FTV, 1TR-FE, 2TR-FE):
    Tester Connection
    Switch Condition
    Specified Condition
    4 (B) - 2 (L)
    A/C switch OFF
    10 kΩ or higher
    A/C switch ON
    Below 1 Ω

    Standard Resistance (for 5L-E):
    Tester Connection
    Switch Condition
    Specified Condition
    3 (E) - 4 (B)
    A/C switch OFF
    10 kΩ or higher
    A/C switch ON
    Below 1 Ω

    Text in Illustration 
    *1
    A/C Switch
    *a
    Component without harness connected
    (Heater Control Knob)
    If the result is not as specified, replace the heater control knob.

  1. Check the A/C indicator operation.

    1. Connect the positive (+) lead from the battery to terminal 2 (L) and the negative (-) lead to terminal 3 (E).

    2. Push the air conditioning switch, and check that the indicator light comes on.

      OK:
      The indicator light comes on.

      If the result is not as specified, replace the heater control knob.

  1. Check the illumination operation.

    1. Connect the positive (+) lead from the battery to terminal 5 (ILL+) and the negative (-) lead to terminal 6 (ILL-), and check that the illumination light comes on.

      OK:
      The illumination light comes on.

      If the result is not as specified, replace the bulb.


INSPECT HEATER CONTROL KNOB (w/o Air Conditioning System)

  1. E289360E01
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    2 (L) - 4 (B)
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Heater Control Knob)
    If the result is not as specified, replace the heater control knob.

  1. Check the illumination operation.

    1. Connect the positive (+) lead from the battery to terminal 5 (ILL+) and the negative (-) lead to terminal 6 (ILL-), and check that the illumination light comes on.

      OK:
      The illumination light comes on.

      If the result is not as specified, replace the bulb.


INSPECT NO. 2 HEATER CONTROL KNOB

  1. E289326E01
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    9 (LO), 7 (M1), 6 (M2), 10 (HI) - 5 (E)
    Blower switch: 0
    10 kΩ or higher
    9 (LO) - 5 (E)
    Blower switch: 1
    Below 1 Ω
    9 (LO), 7 (M1) - 5 (E)
    Blower switch: 1 - 2
    Below 1 Ω
    9 (LO), 7 (M1) - 5 (E)
    Blower switch: 2
    Below 1 Ω
    9 (LO), 7 (M1), 6 (M2) - 5 (E)
    Blower switch: 2 - 3
    Below 1 Ω
    9 (LO), 6 (M2) - 5 (E)
    Blower switch: 3
    Below 1 Ω
    9 (LO), 6 (M2), 10 (HI) - 5 (E)
    Blower switch: 3 - 4
    Below 1 Ω
    9 (LO) 10 (HI) - 5 (E)
    Blower switch: 4
    Below 1 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (No. 2 Heater Control Knob)
    If the result is not as specified, replace the No. 2 heater control knob.

  1. Check the illumination operation.

    1. Connect the positive (+) lead from the battery to terminal 2 (ILL+) and the negative (-) lead to terminal 1 (ILL-), and check that the illumination light comes on.

      OK:
      The illumination light comes on.

      If the result is not as specified, replace the bulb.


INSPECT NO. 3 HEATER CONTROL KNOB (w/ Heater)

  1. E103715E02
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    3 (IG) - 1 (E)
    Rr. DEF switch OFF
    10 kΩ or higher
    3 (IG) - 1 (E)
    Rr. DEF switch ON
    Below 1 Ω
    3 (IG) - 2 (D)
    Rr. DEF switch OFF
    10 kΩ or higher
    3 (IG) - 2 (D)
    Rr. DEF switch ON
    Below 1 Ω
    3 (IG) - 6 (L)
    Except MAX HOT
    10 kΩ or higher
    3 (IG) - 6 (L)
    MAX HOT
    Below 1 Ω

    Text in Illustration 
    *1
    Rr. DEF Switch
    *a
    Max Hot Position
    *b
    Component without harness connected
    (No. 3 Heater Control Knob)
    If the result is not as specified, replace the No. 3 heater control knob.

  1. Check the illumination operation.

    1. Connect the positive (+) lead from the battery to terminal 5 (ILL+) and the negative (-) lead to terminal 4 (ILL-), and check that the illumination light comes on.

      OK:
      The illumination light comes on.

      If the result is not as specified, replace the bulb.


INSPECT NO. 3 HEATER CONTROL KNOB (w/o Heater)

  1. E289354E01
    Turn the No. 3 heater control knob and measure the resistance between terminals 7 (E) and 8 (B).

    OK:
    The resistance changes as shown in the illustration.

    Text in Illustration 
    *a
    Component without harness connected
    (No. 3 Heater Control Knob)
    *b
    Resistance (kΩ)
    *c
    Rotation Angle
    *d
    MAX HOT
    *e
    MAX COOL
    If the result is not as specified, replace the No. 3 heater control knob.

  1. Check the illumination operation.

    1. Connect the positive (+) lead from the battery to terminal 5 (ILL+) and the negative (-) lead to terminal 4 (ILL-), and check that the illumination light comes on.

      OK:
      The illumination light comes on.

      If the result is not as specified, replace the bulb.

← DISASSEMBLY (from Oct 2014)REASSEMBLY (from Oct 2014) →