2014-2019 Hiace · Service Manual INTRODUCTION

CUSTOMIZE PARAMETERS

Removal / installation · Vehicles built from Oct 2014


1. CUSTOMIZE SMART ENTRY AND START SYSTEM (for 1KD FTV, Start Function)

HINT:
The following items can be customized.

NOTICE:
  1. When the customer requests a change in a function, first make sure that the function can be customized.
  2. Record the current settings before customizing.

  1. Customizing with the GTS

    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Customize / Entry&Start.

    5. Select the setting by referring to the table below.

      Entry&Start 
      Display
      Default
      Content
      Setting
      Relevant ECU
      Auto Entry Cancel SW
      OFF
      Function that enables or disables the smart entry and start system.
      OFF or ON
      Certification ECU (smart key ECU assembly)

  1. Entry cancel function (manual operation)

    HINT:
    While the smart entry and start system is canceled, it is possible to lock and unlock the doors with the wireless operation, and the start system can be operated by holding the electrical key transmitter sub-assembly near the engine switch.


    1. The following functions are disabled when the smart entry and start system is canceled.

      1. Entry unlock/lock functions
      2. Push-button start function
      3. Key lock-in prevention function
      4. Entry warning functions

    2. When canceling the system through manual operation:

      1. Make sure the following conditions are met:
        1. The engine switch is off.
        2. The driver door is closed.
        3. The driver door is unlocked.
      2. Press the unlock switch of the electrical key transmitter sub-assembly.
      3. Open the driver door within 5 seconds of completing the step above (driver door: close condition → opened).
      4. With the driver door open, press the unlock switch of the electrical key transmitter sub-assembly 2 times within 5 seconds of completing the step above.

        NOTICE:
        If the driver door is closed before or while pressing the unlock switch, the entry cancel setting mode will end.

      5. Perform the following procedure within 30 seconds of completing the step above.
        1. Close and open the driver door twice (driver door: open → closed → opened → closed → opened).
        2. With the driver door open, press the unlock switch of the electrical key transmitter sub-assembly 2 times.

          NOTICE:
          If the driver door is closed before or while pressing the unlock switch, the entry cancel setting mode will end.

        3. Close and open the driver door (driver door: open → closed → opened).
      6. Close the driver door within 5 seconds (driver door: open → closed).
      7. Check that the wireless buzzer sounds twice (short beeps) to confirm that the smart entry and start system has been canceled.

    3. Perform the following procedure to restore the smart entry and start system to the active state from the canceled state.

      1. Perform the procedures to cancel the smart entry and start system again.
      2. Check that the wireless buzzer sounds once (short beep) to confirm that the smart entry and start system has been restored to the active state.

        HINT:
        1. The system changes between the canceled state and the active state each time the procedure to cancel the system through manual operation is performed.
        2. The buzzer sounds twice when the system changes from the active state to the canceled state, and sounds once when the system changes from the canceled state to the active state.


2. CUSTOMIZE SEAT BELT WARNING SYSTEM

NOTICE:
  1. When the customer requests a change in a function, first make sure that the function can be customized.
  2. Record the current settings before customizing.

  1. Customizing with the GTS

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Utility / Customize Setting / Warning.

    5. Select the setting by referring to the table below.

      Warning 
      Display
      Default
      Content
      Setting
      Relevant ECU
      Driver Side Seatbelt Warning Buzzer*1
      ON
      Function to turn on/off the seat belt warning buzzer
      ON or OFF
      Combination meter assembly
      Front Passenger Side Seatbelt Warning Buzzer*2
      ON
      Function to turn on/off the seat belt warning buzzer
      ON or OFF
      Combination meter assembly
      1. *1: w/ Driver Side Seat Belt Warning Buzzer
      2. *2: w/ Front Passenger Seat Belt Warning System

      HINT:
      This setting is only valid for the buzzer which sounds at 20 km/h (12 mph) or more


3. CUSTOMIZE WIRELESS DOOR LOCK CONTROL SYSTEM (w/ Smart Entry and Start System)

HINT:
The following items can be customized.

NOTICE:
  1. When the customer requests a change in a function, first make sure that the function can be customized.
  2. Be sure to make a note of the current settings before customizing.
  3. When troubleshooting a function, first make sure that the function is set to the default setting.

  1. Customizing with the GTS

    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Entry&Start / Utility / Customize / Door Lock.

      Entry&Start 
      Display
      Default
      Content
      Setting
      Relevant ECU
      Wireless Buzzer Volume Setting
      Level5
      Function that changes the wireless buzzer volume.
      OFF, Level7(MAX), Level6, Level5, Level 4, Level3, Level2, Level1, Level0(Mute)
      Certification ECU (smart key ECU assembly)


4. CUSTOMIZE SMART ENTRY AND START SYSTEM (for Entry Function)

HINT:
The following items can be customized.

NOTICE:
  1. When the customer requests a change in a function, first make sure that the function can be customized.
  2. Record the current settings before customizing.

  1. Customizing with the GTS

    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Customize Setting / Entry&Start.

    5. Select the setting by referring to the table below.

      Entry&Start 
      Display
      Default
      Content
      Setting
      Relevant ECU
      Door Unlock Mode2
      All
      Function that chooses the doors to be operated by entry unlock operation.
      All, Driver
      Certification ECU (smart key ECU assembly)
      Auto Entry Cancel SW
      OFF
      Function that enables or disables the smart entry and start system.
      OFF, ON
      Certification ECU (smart key ECU assembly)
      Wireless Buzzer Volume Setting
      Level5
      Wireless buzzer answer back volume.
      OFF, Level7(MAX), Level6, Level5, Level4, Level3, Level2, Level1, Level0(Mute)
      Certification ECU (smart key ECU assembly)

  1. Entry cancel function (manual operation)

    HINT:
    While the smart entry and start system is canceled, it is possible to lock and unlock the doors with the wireless operation, and the start system can be operated by holding the electrical key transmitter sub-assembly near the engine switch.


    1. The following functions are disabled when the smart entry and start system is canceled.

      1. Entry unlock/lock functions
      2. Push start function
      3. Key lock-in prevention function
      4. Entry warning functions

    2. When canceling the system through manual operation:

      1. Make sure the following conditions are met:
        1. The engine switch is off.
        2. The driver door is closed.
        3. The driver door is unlocked.
      2. Press the unlock button of the electrical key transmitter sub-assembly.
      3. Open the driver door within 5 seconds of completing the step above (driver door: close condition → opened).
      4. With the driver door open, press the unlock button of the electrical key transmitter sub-assembly 2 times within 5 seconds of completing the step above.

        NOTICE:
        If the driver door is closed before or while pressing the unlock button, the entry cancel setting mode will end.

      5. Close and open the driver door twice completing the above step (driver door: open condition → closed → opened → closed → opened).
      6. With the driver door open, press the unlock button of the electrical key transmitter sub-assembly 2 times completing the step above.

        NOTICE:
        If the driver door is closed before or while pressing the unlock button, the entry cancel setting mode will end.

      7. Close and open the driver door completing the step above (driver door: open condition → closed → opened).
      8. Close the driver door within 5 seconds of completing the above step.
      9. Check that the wireless buzzer sounds twice (short beeps) to confirm that the smart entry and start system has been canceled.

        HINT:
        Finish the step 5 to 7 within 30 seconds.

    3. Perform the following procedure to restore the smart entry and start system to the active state from the canceled state.

      1. Perform the procedures to cancel the smart entry and start system again.
      2. Check that the wireless buzzer sounds once (short beep) to confirm that the smart entry and start system has been restored to the active state.

        HINT:
        1. The system changes between the canceled state and the active state each time the procedure to cancel the system through manual operation is performed.
        2. The buzzer sounds twice when the system changes from the active state to the canceled state, and sounds once when the system changes from the canceled state to the active state.


5. CUSTOMIZE LIGHTING SYSTEM

HINT:
The following items can be customized.

NOTICE:
  1. When the customer requests a change in a function, first make sure that the function can be customized.
  2. Record the current settings before customizing.

  1. Customizing with the GTS.

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Utility / Customize / Warning.

    5. Select the setting by referring to the table below.

      Warning 
      Display
      Default
      Content
      Setting
      Relevant ECU
      Lane Change Flashing Times Setting
      3
      Function to change the number of flashes for the lane change flasher
      OFF, 3, 5 or 7
      Combination meter assembly
      Flasher Sound Tone Setting
      Tone 3
      Function to change the flasher sound.
      Tone 1, Tone 2 or Tone 3
      Combination meter assembly


6. CUSTOMIZE METER / GAUGE SYSTEM
  1. Customizing with the GTS

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Customize Setting / Combination Meter / Warning or Display.

    5. Select the setting by referring to the table below.

      Warning 
      Display
      Default
      Content
      Setting
      Relevant ECU
      Driver Side Seatbelt Warning Buzzer*
      ON
      Function to turn on/off the seat belt warning buzzer
      ON or OFF
      Combination meter assembly
      Front Passenger Side Seatbelt Warning Buzzer*
      ON
      Function to turn on/off the seat belt warning buzzer
      ON or OFF
      Combination meter assembly
      Lane Change Flashing Times Setting
      3
      Function to change the lane change flashing time
      OFF, 3, 5 or 7
      Combination meter assembly
      Flasher Sound Tone Setting
      Tone 3
      Function to change the flasher sound tone
      Tone 1, Tone 2 or Tone 3
      Combination meter assembly
      1. *: This setting is only valid for the buzzer which sounds at 20 km/h (12 mph) or more
      Display 
      Display
      Default
      Content
      Setting
      Relevant ECU
      ECO Drive Indicator Zone
      ON
      Function to turn on/off the eco driving indicator zone display
      ON or OFF
      Combination meter assembly
      ODO Display Time After IG OFF Setting
      30 s
      Function to change the odometer display time
      30 s, 60 s, 600 s or OFF
      Combination meter assembly

  1. Customizing with the combination meter assembly (for Dot Display Type)

    1. Turn the ignition switch to ON.

    2. Enter the following menus: SETTINGS.

    3. Select the setting by referring to the table below.

      SETTINGS 
      Display
      Default
      Content
      Setting
      Relevant ECU
      LANGUAGE
      ENGLISH
      Function to change the multi-information display language
      ENGLISH or Chinese
      Combination meter assembly
      UNITS
      L/100km
      Function to change the multi-information display unit
      km/L or L/100km
      Combination meter assembly
      ECO INDICATOR
      ON
      Function to turn on/off the eco driving indicator light
      ON or OFF
      Combination meter assembly

  1. Customizing with the combination meter assembly (for Segment Display Type)

    1. Turn the ignition switch to ON.

    2. Display the odometer screen.

    3. Press and hold the ODO/TRIP switch for 5 seconds or more to display the settings screen.

    4. After selecting "Eco On" or "EcoOFF", press and hold the ODO/TRIP switch for 2 seconds or more to exit the settings screen.

  1. Inspect T-BELT mode display (Engine Type Diesel)

    1. Turn the ignition switch to ON.

    2. Turn the ODO/TRIP display screen to "TRIP B", and turn the ignition switch off.

    3. While pressing the ODO/TRIP change switch, turn the ignition switch to ON to blink the T-BELT warning light, and then continue pressing the switch for 5 seconds or more.

    4. Release the ODO/TRIP switch, then press the ODO/TRIP switch again within 5 seconds.

    5. Transfer to the T-BELT mode, and the following initial setting value is displayed.
      km: 15 (0,000 km) or 9 (0,000 mile)

      HINT:
      If the meter has been replaced before, the displayed value might not be the same as the initial setting value.

  1. Rewriting replacement setting value (Engine Type Diesel)

    1. Press the ODO/TRIP switch and rewrite the replacement setting value.

      Condition
      Setting value
      When a belt is replaced
      km: 15 (0,000 km)
      mile: 9 (0,000 mile)
      When a meter is replaced
      km: [15 (0,000 km)] - (Mileage when the meter is replaced)
      mile: [9 (0,000 mile)] - (Mileage when the meter is replaced)

      HINT:
      Every press of the ODO/TRIP switch adds 10,000 km or 10,000 mile and the meter returns to 10,000 km or 10,000 mile when 200,000 km or 200,000 mile is reached. If switch operation is not performed within 30 seconds, the setting value will not be changed. The display screen turns to "TRIP B", and the mode returns to the normal mode.

  1. T-BELT mode completion (Engine Type Diesel)

    NOTICE:
    If the T-BELT mode is completed, even though belt replacement or meter replacement has not been performed, the T-BELT warning is reset.


    1. After setting the replacement setting value, hold the ODO/TRIP switch on for more than 5 seconds, then release the ODO/TRIP switch.

    2. Check that the display is changed to "TRIP B" and the warning light goes off.

← VEHICLE LIFT AND SUPPORT LOCATIONS (from Oct 2014)INITIALIZATION (Oct 2014 – Dec 2014) →