2014-2019 Hiace · Service Manual COMMUNICATION SYSTEM

AFS ECU Communication Stop Mode

Circuit diagnosis · Vehicles built Apr 2016 – Dec 2016

Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Mar 2016 Apr 2016 – Dec 2016 from Jan 2017

DESCRIPTION

Detection Item
Symptom
Trouble Area
AFS ECU Communication Stop Mode
Either condition is met:
  1. "Headlight swivel (AFS)" is not displayed on "Bus Check".
  2. "AFS ECU Communication Stop Mode" in "DTC Combination Table" applies.
  1. Power source or inside headlight leveling ECU assembly
  2. Headlight leveling ECU assembly CAN branch wire or connector
  3. Headlight leveling ECU assembly
  1. For vehicles with an LED headlight.

WIRING DIAGRAM

C280373E02

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

    CAUTION:
    For vehicles with an airbag system:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


NEXT


2. CHECK FOR OPEN IN CAN BUS WIRE (HEADLIGHT LEVELING ECU ASSEMBLY CAN BRANCH WIRE)

  1. C268313E17
    Disconnect the headlight leveling ECU assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A39-6 (CANH) - A39-7 (CANL)
    Ignition switch off
    54 to 69 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Headlight Leveling ECU Assembly)



NG
REPAIR OR REPLACE HEADLIGHT LEVELING ECU ASSEMBLY CAN BRANCH WIRE OR CONNECTOR (CANH, CANL)
OK


3. CHECK HARNESS AND CONNECTOR (HEADLIGHT LEVELING ECU ASSEMBLY - BATTERY AND BODY GROUND)

  1. C268313E18
    Connect the cable to the negative (-) battery terminal.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A39-9 (E1) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A39-1 (IG) - Body ground
    Ignition switch ON
    11 to 14 V

Text in Illustration 
*a
Front view of wire harness connector
(to Headlight Leveling ECU Assembly)
Result 
Result
Proceed to
OK (for LHD)
A
OK (for RHD)
B
NG
C


B
REPLACE HEADLIGHT LEVELING ECU ASSEMBLY (Click here)

C
REPAIR OR REPLACE HARNESS OR CONNECTOR
A

REPLACE HEADLIGHT LEVELING ECU ASSEMBLY (Click here)


← AFS ECU Communication Stop Mode (Jan 2015 – Mar 2016)AFS ECU Communication Stop Mode (from Jan 2017) →