2014-2019 Hiace · Service Manual BODY ELECTRICAL

ON-VEHICLE INSPECTION

Inspection · Vehicles built from Oct 2014


INSPECT WINDSHIELD WIPER SWITCH ASSEMBLY (for LHD)

  1. E257039E05
    Intermittent Operation Check (w/o Intermittent timing adjustment)
    Text in Illustration 
    *a
    Component with harness connected
    (Windshield Wiper Switch Assembly)

    1. Connect a voltmeter positive (+) lead to terminal 3 (+1) and a negative (-) lead to terminal 4 (EW).

    2. Turn the ignition switch to ON.

    3. Turn the wiper switch to the INT position.

    4. Operate the intermittent wiper relay and check the voltage between terminals 3 (+1) and 4 (EW).

      OK:
      Voltage changes as shown in the illustration.


      E226601E02
      If the result is not as specified, replace the windshield wiper switch assembly.

  1. E257039E05
    Intermittent Operation Check (w/ Intermittent timing adjustment)
    Text in Illustration 
    *a
    Component with harness connected
    (Windshield Wiper Switch Assembly)

    1. Connect a voltmeter positive (+) lead to terminal 3 (+1) and a negative (-) lead to terminal 4 (EW).

    2. Turn the ignition switch to ON.

    3. Turn the wiper switch to the INT position.

    4. Operate the intermittent wiper relay and check the voltage between terminals 3 (+1) and 4 (EW).

      OK:
      Voltage changes as shown in the illustration.


      E136493E30
      If the result is not as specified, replace the windshield wiper switch assembly.

  1. E257039E06
    Front Washer Operation Check
    Text in Illustration 
    *a
    Component with harness connected
    (Windshield Wiper Switch Assembly)

    1. Connect a voltmeter positive (+) lead to terminal 7 (WF) and a negative (-) lead to Body ground.

    2. Turn the ignition switch to ON.

    3. Turn the washer switch on and off, and check the voltage between terminals 7 (WF) and Body ground.

      OK:
      Voltage changes as shown in the illustration.


      E226602E21

  1. E257039E07
    Rear Washer Operation Check
    Text in Illustration 
    *a
    Component with harness connected
    (Windshield Wiper Switch Assembly)

    1. Connect a voltmeter positive (+) lead to terminal 5 (WR) and a negative (-) lead to Body ground.

    2. Turn the ignition switch to ON.

    3. Turn the washer switch on and off, and check the voltage between terminals 5 (WR) and Body ground.

      OK:
      Voltage changes as shown in the illustration.


      E226602E23


INSPECT WINDSHIELD WIPER SWITCH ASSEMBLY (for RHD)

  1. E239385E08
    Intermittent Operation Check (w/o Intermittent timing adjustment)
    Text in Illustration 
    *a
    Component with harness connected
    (Windshield Wiper Switch Assembly)

    1. Connect a voltmeter positive (+) lead to terminal 2 (+1) and a negative (-) lead to terminal 7 (EW).

    2. Turn the ignition switch to ON.

    3. Turn the wiper switch to the INT position.

    4. Operate the intermittent wiper relay and check the voltage between terminals 2 (+1) and 7 (EW).

      OK:
      Voltage changes as shown in the illustration.


      E226601E04
      If the result is not as specified, replace the windshield wiper switch assembly.

  1. E239385E08
    Intermittent Operation Check (w/ Intermittent timing adjustment)
    Text in Illustration 
    *a
    Component with harness connected
    (Windshield Wiper Switch Assembly)

    1. Connect a voltmeter positive (+) lead to terminal 2 (+1) and a negative (-) lead to terminal 7 (EW).

    2. Turn the ignition switch to ON.

    3. Turn the wiper switch to the INT position.

    4. Operate the intermittent wiper relay and check the voltage between terminals 2 (+1) and 7 (EW).

      OK:
      Voltage changes as shown in the illustration.


      E136493E31
      If the result is not as specified, replace the windshield wiper switch assembly.

  1. E239385E10
    Front Washer Operation Check
    Text in Illustration 
    *a
    Component with harness connected
    (Windshield Wiper Switch Assembly)

    1. Connect a voltmeter positive (+) lead to terminal 4 (WF) and a negative (-) lead to Body ground.

    2. Turn the ignition switch to ON.

    3. Turn the washer switch on and off, and check the voltage between terminals 4 (WF) and Body ground.

      OK:
      Voltage changes as shown in the illustration.


      E226602E22

  1. E239385E11
    Rear Washer Operation Check
    Text in Illustration 
    *a
    Component with harness connected
    (Windshield Wiper Switch Assembly)

    1. Connect a voltmeter positive (+) lead to terminal 10 (WR) and a negative (-) lead to Body ground.

    2. Turn the ignition switch to ON.

    3. Turn the washer switch on and off, and check the voltage between terminals 10 (WR) and Body ground.

      OK:
      Voltage changes as shown in the illustration.


      E226602E24

← COMPONENTS (from Oct 2014)REMOVAL (Oct 2014 – Dec 2014) →