2014-2019 Hiace · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built Jan 2017 – Nov 2017

Versions by build date: Jan 2017 – Nov 2017 from Dec 2017


1. DRAIN ENGINE COOLANT

CAUTION:
Do not remove the radiator cap sub-assembly while the engine assembly and radiator assembly are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Connect a hose with an inside diameter of 9 mm (0.354 in.) to the radiator drain cock.

  1. Loosen the radiator drain cock plug.

    A397672E03

    Text in Illustration 
    *1
    Bleeder Plug
    *2
    Radiator Cap Sub-assembly
    *3
    Radiator Reserve Tank Assembly
    *4
    Cylinder Block Drain Cock Plug
    *5
    Radiator Drain Cock Plug
    -
    -

  1. Remove the radiator cap sub-assembly.

  1. Loosen the cylinder block drain cock plug, and drain the engine coolant.

  1. Tighten the radiator drain cock plug.

  1. Tighten the cylinder block drain cock plug.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf }

  1. Disconnect the hose from the radiator drain cock.


2. REMOVE SEAT TRACK COVER LH

  1. B462969
    Using a clip remover, remove the clip.

  1. Detach the claw and remove the seat track cover LH.


3. REMOVE FRONT SEAT ASSEMBLY RH

  1. B107542
    Move the front seat assembly fully forward.

  1. Remove the 2 bolts on the rear side of the seat.

  1. Move the front seat assembly to the rearmost position.

  1. Remove the 2 bolts on the front side of the seat.

  1. Move the front seat assembly to the center of the seat slide rail. Set the seatback in the upright position.

  1. Disconnect the front seat inner belt assembly connector.

  1. Remove the front seat assembly.


4. REMOVE FRONT DOOR SCUFF PLATE RH

5. REMOVE ENGINE SERVICE HOLE SUB COVER SUB-ASSEMBLY
  1. Fold back the floor carpet.

  1. Remove the 5 bolts and engine service hole sub cover sub-assembly.


6. REMOVE TRANSMISSION SERVICE HOLE COVER SUB-ASSEMBLY
  1. Remove the 2 seat belt anchor covers.

  1. A349439
    Remove the 2 bolts and disconnect the front center seat belt assembly RH and front center seat lap type belt assembly.

  1. Detach the clips and fold back the carpet.

  1. A349440
    Remove the 4 bolts and transmission service hole cover sub-assembly from the body.


7. REMOVE DIESEL THROTTLE BODY ASSEMBLY
(Click here)

8. REMOVE NO. 16 WATER BY-PASS HOSE

  1. A396753
    Slide the 2 clamps and remove the No. 16 water by-pass hose from the No. 1 EGR cooler and No. 2 water by-pass pipe.


9. REMOVE DIESEL TURBO PRESSURE SENSOR

  1. A396756
    Disconnect the connector from the diesel turbo pressure sensor.

  1. Remove the bolt and diesel turbo pressure sensor from the No. 3 water by-pass pipe sub-assembly.


10. DISCONNECT ENGINE WIRE

  1. A396797
    Detach the 2 clamps and disconnect the 2 connectors from the turbocharger sub-assembly.

  1. Disconnect the connector from the camshaft position sensor.

  1. A396798
    Detach the clamp and disconnect the connector from the differential pressure sensor.

  1. Disconnect the 3 connectors from the exhaust gas temperature sensors.

  1. Disconnect the connector from the exhaust fuel addition injector assembly.

  1. A396799
    Disconnect the 4 connectors from the 4 injector assemblies.

  1. Disconnect the electric EGR control valve assembly.

  1. Disconnect the connector from the glow plug connector.

  1. Disconnect the connector from the sensor wire of common rail assembly.

  1. A396800
    Detach the 2 clamps and remove the 4 bolts.

  1. A396801
    Disconnect the connector from the swirl control valve.

  1. Disconnect the connector from the vacuum control valve set.

  1. Detach the 2 clamps and disconnect the engine wire from the engine assembly.


11. REMOVE EGR VALVE BRACKET

  1. A396757
    Remove the bolt, nut and EGR valve bracket from the electric EGR control valve assembly and intake manifold.


12. REMOVE NO. 2 EGR PIPE

  1. A396758
    Remove the bolt, 4 nuts and No. 2 EGR pipe from the electric EGR control valve assembly and intake manifold.

  1. Remove the 2 gaskets.


13. REMOVE NO. 3 WATER BY-PASS PIPE SUB-ASSEMBLY

  1. A396761
    Disconnect the No. 4 fuel hose from the No. 3 water by-pass pipe sub-assembly.

  1. A396779
    Slide the clamp and disconnect the No. 8 water by-pass hose from the No. 3 water by-pass pipe sub-assembly.

  1. Slide the clamp and disconnect the No. 9 water by-pass hose from the electric EGR control valve assembly.

  1. Remove the 2 bolts and No. 3 water by-pass pipe sub-assembly from the No. 1 EGR cooler.


14. DISCONNECT NO. 4 WATER BY-PASS PIPE SUB-ASSEMBLY

  1. A396763
    Slide the clamp and disconnect the No. 7 water by-pass hose from the No. 1 EGR cooler.

  1. Slide the clamp and disconnect the water hose from the No. 2 EGR valve assembly.

  1. A396764
    Remove the 2 bolts and disconnect the No. 4 water by-pass pipe sub-assembly from the intake manifold.


15. REMOVE EGR PIPE INSULATOR

  1. A405485E01
    Detach the clip and EGR pipe insulator from the No. 1 EGR pipe sub-assembly.


16. REMOVE NO. 1 EGR PIPE SUB-ASSEMBLY

  1. A396765
    Remove the bolt and disconnect the No. 1 EGR pipe sub-assembly from the vacuum transmitting pipe sub-assembly.

  1. A396766
    Remove the 4 nuts and the No. 1 EGR pipe sub-assembly from the exhaust manifold and EGR valve adapter.

  1. Remove the 2 gaskets.

  1. A396767
    Using an E8 "TORX" socket wrench, remove the 2 stud bolts from the exhaust manifold.


17. REMOVE VACUUM CONTROL VALVE SET
  1. Disconnect the connector from the vacuum control valve set.

  1. A396768
    Disconnect the 2 vacuum hoses from the vacuum control valve set and No. 2 EGR valve assembly.

  1. A396769
    Remove the 2 bolts and vacuum control valve set from the intake manifold.


18. REMOVE NO. 1 EGR COOLER AND NO. 2 EGR VALVE ASSEMBLY WITH ELECTRIC EGR CONTROL VALVE ASSEMBLY

  1. A396780
    Remove the 4 bolts and No. 1 EGR cooler and No. 2 EGR valve assembly with electric EGR control valve assembly from the intake manifold.


19. REMOVE NO. 1 EGR COOLER

  1. A396781
    Remove the 4 bolts and No. 1 EGR cooler from the No. 2 EGR valve assembly with electric EGR control valve assembly.

  1. Remove the gasket.

← COMPONENTS (from Dec 2017)REMOVAL (from Dec 2017) →