Home › General › INTRODUCTION › WORK NOTICES AND PRECAUTIONS › 2019.02–2019.06
BM35X0E _V1 General _080416 INTRODUCTION _0389975 WORK NOTICES AND PRECAUTIONS F

INTRODUCTION  WORK NOTICES AND PRECAUTIONS  PRECAUTIONS FOR BLIND SPOT MONITOR  


BLIND SPOT MONITOR DESCRIPTION


a.

Blind spot monitor sensor radiate electromagnetic waves to detect other vehicles driving in the blind spots of the vehicle having the sensor, and then the indicator lamps are lit up or flashed to assist the driver in checking for safe movement when changing lanes.


b.
K140801C01
1.802,1.063 2.333,0.281 2.333,0.281 2.646,0.281 false 0.146,0.073 0.458,0.271 0.313,0.198 10 false *a 0.375,1.094 0.688,1.292 0.313,0.198 10 false *b 1.135,1.896 1.448,2.094 0.313,0.198 10 false *c 2.719,0.208 3.031,0.406 0.313,0.198 10 false *1
*1 BLIND SPOT MONITOR SENSOR
*a Expansion of Electromagnetic Waves (Example)
*b Vertically 60°
*c Horizontally 160°


The radiation range of the electromagnetic waves expands vertically and horizontally in relation to the sensor.



INSPECTION PROCEDURES FOR THE BLIND SPOT MONITOR SENSOR BRACKET AND INSTALLATION AREA


K140802E03
0.25,0.333 1.552,0.542 1.302,0.208 10 false (Sheet metal repair) 0.198,0.646 1.49,1.208 1.292,0.563 10 false Repair or replace the bracket installation panel 2.333,0.365 4.458,0.583 2.125,0.219 10 false (Sheet metal work, at completion) 2.521,0.563 4.156,0.927 1.635,0.365 10 false Check installation angle of blind spot monitor sensor 5.302,0.5 6.844,0.875 1.542,0.375 10 false Functional inspection of blind spot monitor sensor 4.573,1.073 5.083,1.26 0.51,0.188 10 false Correct 1.813,2.167 2.438,2.365 0.625,0.198 10 false Incorrect 6.781,0.396 6.906,0.521 0.125,0.125 10 false *

a.

If you have replaced the bracket installation panel or blind spot monitor bracket, let alone repaired the bracket installation panel, the sensor installation angle must be checked since it may become misaligned.


b.

Be sure to always perform a functional inspection after any body repair. (This is performed as a comprehensive inspection with the bumper installed.)

*For functional inspection procedures, refer to the electronic manual (repair manual).



PROCEDURES FOR MEASURING THE INSTALLATION ANGLE OF BLIND SPOT MONITOR SENSOR


a.

The installation angle is measured at the planes A, B, and C by use of a digital angle meter, 3D measuring instrument, or similar instrument.


b.

For B and C, measure the sensor planes by use of a digital angle meter, or measure the position of the sensor bracket.


c.

As an angle meter cannot be used to measure A, measure the sensor bracket (dimension y).

K152088C01
5,2.25 6.833,4.417 1.833,2.167 1.333,0.083 1.646,0.24 0.313,0.156 10 false *a 3.604,0.083 3.917,0.24 0.313,0.156 10 false *b 3.198,2.354 3.51,2.51 0.313,0.156 10 false *c 5.833,2.333 6.146,2.49 0.313,0.156 10 false *d 1.896,4.438 2.208,4.594 0.313,0.156 10 false *e 3.438,1.958 3.677,2.177 0.24,0.219 10 false y 4.844,1.292 5.083,1.51 0.24,0.219 10 false y 6.083,0.083 6.396,0.24 0.313,0.156 10 false *a 1.188,2.333 1.5,2.49 0.313,0.156 10 false *b 1.396,2.865 1.708,3.021 0.313,0.156 10 false (B) 3.813,2.688 4.125,2.844 0.313,0.156 10 false (C) 0.833,2.521 1.146,2.677 0.313,0.156 10 false B 4.229,3.281 4.542,3.438 0.313,0.156 10 false C 0.708,2.094 1.021,2.25 0.313,0.156 10 false A
*a Top View *b Rear View
*c Side View *d Sensor reference plane if measuring with a digital angle meter
*e B/C: Measure along either the horizontal or vertical axis - -




RADIATION RANGES OF THE ELECTROMAGNETIC WAVES OF THE BLIND SPOT MONITOR SENSOR IN RELATION TO THE BUMPER


a.

Measure dimensions along the front surface of the bumper.

K151562C01
3.708,4.396 3.927,4.604 0.219,0.208 10 true *a 3.271,5.01 3.49,5.229 0.219,0.219 10 true *b 4.896,5.188 5.125,5.417 0.229,0.229 10 true *c 3.344,5.844 3.563,6.052 0.219,0.208 10 true *a
*a 49 mm (1.93 in.) *b 154 mm (6.06 in.)
*c 158 mm (6.22 in.) - -
K108837

Radiation Range of Electromagnetic Waves - -




PROHIBITIONS REGARDING RADIATION RANGE OF ELECTROMAGNETIC WAVES


a.

The following work is prohibited within the radiation ranges of electromagnetic waves because they might affect the waves.

i.

Putty application repair of damaged areas

HINT:

Repair by painting is allowed for slight damage that can be filled in by a primer surfacer or paint.


K140804C01
2.031,0.063 2.344,0.26 0.313,0.198 10 false *a 5.521,0.052 5.833,0.25 0.313,0.198 10 false *b 0.583,1.656 0.896,1.854 0.313,0.198 10 false *d 6.052,1.552 6.365,1.75 0.313,0.198 10 false *c 4.188,1.646 4.5,1.844 0.313,0.198 10 false *d 2.542,1.542 2.854,1.74 0.313,0.198 10 false *c 2.208,1.844 2.521,2.042 0.313,0.198 10 false *c
*a Avoid the radiation ranges of electromagnetic waves *b Apply only primer surfacer to repair damage
*c Radiation Range of Electromagnetic Waves *d Cross-Section
K108841

REAR BUMPER COVER
K110100

BLIND SOPT MONITOR SENSOR
K110580

Putty
K108850

Primer surfacer


K140805C01
2.063,0.052 2.375,0.25 0.313,0.198 10 false *a 5.573,0.052 5.885,0.25 0.313,0.198 10 false *b 2.583,1.552 2.896,1.75 0.313,0.198 10 false *c 0.75,1.698 1.063,1.896 0.313,0.198 10 false *d 6.042,1.542 6.354,1.74 0.313,0.198 10 false *c 5.49,1.875 5.802,2.073 0.313,0.198 10 false *c 2.063,1.875 2.375,2.073 0.313,0.198 10 false *c 4.26,1.698 4.573,1.896 0.313,0.198 10 false *d
*a Putty is present within the radiation range of electromagnetic waves *b Putty is applied to damage within the radiation range of electromagnetic waves
*c Radiation Range of Electromagnetic Waves *d Cross-Section
K108841

REAR BUMPER COVER
K110100

BLIND SOPT MONITOR SENSOR
K110580

Putty - -



ii.

Paint work having paint boundaries (boundaries of final color or gradations) within the radiation range of electromagnetic waves

HINT:

There is no problem if the entire radiation range of electromagnetic waves is completely painted.


K140806C01
2.552,1.542 2.76,1.698 0.208,0.156 10 false *c 0.823,1.656 1.031,1.813 0.208,0.156 10 false *d 2.208,0.094 2.417,0.25 0.208,0.156 10 false *a 5.583,0.094 5.792,0.25 0.208,0.156 10 false *b 6,1.563 6.208,1.719 0.208,0.156 10 false *c 4.01,1.656 4.219,1.813 0.208,0.156 10 false *d 1.625,2.521 1.833,2.677 0.208,0.156 10 false *e 2.635,1.781 2.844,1.938 0.208,0.156 10 false *c 5.438,1.729 5.646,1.885 0.208,0.156 10 false *c
*a Avoid the radiation ranges of electromagnetic waves *b Radiation range of electromagnetic waves is covered
*c Radiation Range of Electromagnetic Waves *d Cross-Section
*e Clear - -
K108841

REAR BUMPER COVER
K110100

BLIND SOPT MONITOR SENSOR
K108850

Final Color
K108851

Gradation


K140807C03
2.073,0.146 2.385,0.344 0.313,0.198 10 false *a 5.5,0.135 5.813,0.333 0.313,0.198 10 false *b 2.479,1.625 2.792,1.823 0.313,0.198 10 false *c 2.375,1.854 2.688,2.052 0.313,0.198 10 false *c 1.177,1.781 1.49,1.979 0.313,0.198 10 false *d 5.938,1.635 6.25,1.833 0.313,0.198 10 false *c 5.188,2.083 5.5,2.281 0.313,0.198 10 false *c 1.188,2.885 1.5,3.083 0.313,0.198 10 false *d 2.354,2.969 2.667,3.167 0.313,0.198 10 false *c 4.167,2 4.479,2.198 0.313,0.198 10 false *d
*a Paint boundary is present within the radiation range of electromagnetic waves *b Gradation is present within the radiation range of electromagnetic waves
*c Radiation Range of Electromagnetic Waves *d Cross-Section
K108841

REAR BUMPER COVER
K110100

BLIND SOPT MONITOR SENSOR
K108850

Final Color
K108851

Gradation



iii.

Resin repair of cracks and perforations

HINT:

Always replace the rear bumper cover if there are cracks or perforations in the radiation range of electromagnetic waves.


K140808C01
3.292,1.542 3.604,1.74 0.313,0.198 10 false *a
*a Radiation Range of Electromagnetic Waves - -
K108850

Cracks or perforation - -


K140809C01
3.323,1.583 3.635,1.781 0.313,0.198 10 false *a
*a Radiation Range of Electromagnetic Waves - -
K108850

Cracks or perforation - -



iv.

Bumper customization (Work affecting the shape or paint color of the bumper)