Home › Vehicle Exterior › BODY PANEL › REAR FLOOR STEP (for Standard Roof) › 2019.02–2019.06
BM35X0E _01 Vehicle Exterior _080418 BODY PANEL _0390001 REAR FLOOR STEP(for Standard Roof) F

BODY PANEL  REAR FLOOR STEP(for Standard Roof)  ASSEMBLY REPLACEMENT  


K151893

With the center body pillar cut and join replacement sections, rocker outer rear panel cut and join replacement sections and quarter panel cut and join replacement sections (small areas) removed.


REMOVAL


Symbol Meaning
K108818

Remove Weld Points
K108820

Remove Weld Points
K108827

Cut and Join Location

a.

Remove the floor side rail plate sub-assembly.

K151493C01
3.885,0.958 4,0.333 4,0.333 4.167,0.333 false 0.188,0.167 0.5,0.323 0.313,0.156 10 false *A 4.219,0.26 4.531,0.417 0.313,0.156 10 false *1
*A LH - -
*1 FLOOR SIDE RAIL PLATE SUB-ASSEMBLY - -



b.

Remove the floor side rail plate.

K151494C01
3.208,1.156 3,0.417 3,0.417 2.833,0.417 false 0.167,0.177 0.479,0.333 0.313,0.156 10 false *A 2.646,0.333 2.958,0.49 0.313,0.156 10 false *1
*A RH - -
*1 FLOOR SIDE RAIL PLATE - -



c.

Roughly cut open the panel so that the adhesive can be reached. Cut through the adhesive with a cut chisel to remove the panel.

HINT:

In cases where the adhesive cannot be removed with a cut chisel, heat the adhesive with an industrial heater gun or gas burner taking care not to cause panel deformation by overheating.


K151489C01
0,0 0,0 false
K108837

Adhesive - -



d.

Remove the A.

HINT:

A is reused.


K151488C01
2.448,2.135 2.833,2.833 2.833,2.833 3,2.833 false 3.635,1.271 3.948,1.427 0.313,0.156 10 false *a 3.073,2.75 3.385,2.906 0.313,0.156 10 false A
*a 20 mm (0.79 in.) - -



e.

Roughly cut open the panel so that the adhesive can be reached. Cut through the adhesive with a cut chisel to remove the panel.

HINT:

In cases where the adhesive cannot be removed with a cut chisel, heat the adhesive with an industrial heater gun or gas burner taking care not to cause panel deformation by overheating.


K151491C01
0,0 0,0 false
K108837

Adhesive - -



f.

Remove the A.

HINT:

A is reused.


K151490C01
4.417,3.5 4.25,3.5 4.25,3.5 4.01,2.823 false 1.677,1.396 1.99,1.552 0.313,0.156 10 false *a 4.49,3.417 4.802,3.573 0.313,0.156 10 false A
*a 40 mm (1.57 in.) - -



g.

Remove the A.

HINT:

A is reused.


K151492C01
2.5,3.583 2.333,3.583 2.333,3.583 2.135,2.979 false 0.125,1.427 0.438,1.583 0.313,0.156 10 false *a 2.583,3.5 2.896,3.656 0.313,0.156 10 false A
*a 65 mm (2.56 in.) - -



h.

Remove the step sub-assembly.

K151495C01
3.417,3.333 3.25,3.333 3.25,3.333 3.479,2.74 false 3.5,3.25 3.813,3.448 0.313,0.198 10 false *1
*1 STEP SUB-ASSEMBLY - -


K151496C01
0.25,0.167 6.917,3.583 6.667,3.417 3.583,3.583 3.583,0.167 false 0.333,0.26 0.646,0.417 0.313,0.156 10 false *A 3.667,0.26 3.979,0.417 0.313,0.156 10 false *B
*A LH *B RH


K151497

K151498

K151499

K151500



INSTALLATION


Symbol Meaning
K108820

Remove Weld Points
K108823

Plug Weld
K108825

Plug Weld
K108831

Butt Weld
K108834

Body Sealer

a.

Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.


b.

Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimensions)


c.

If the entire supply part is not needed, remove the part of the supply part that is needed.

K151501C01
4.646,2 5,2.583 5,2.583 5.167,2.583 false 5.25,2.51 5.563,2.667 0.313,0.156 10 false *1
*1 STEP SUB-ASSEMBLY - -



d.

Before installing a new part, apply body sealer.

HINT:

Apply body sealer in an even, continuous bead.


K151508


e.

Weld the A to the vehicle side.

K151502N01
3.5,3.417 3.333,3.417 3.333,3.417 3.458,2.75 false 3.594,3.333 3.75,3.531 0.156,0.198 10 false A

K151503C01
0.167,0.167 7,3.667 6.833,3.5 3.583,3.667 3.583,0.167 false 0.25,0.26 0.563,0.417 0.313,0.156 10 false *A 3.667,0.26 3.979,0.417 0.313,0.156 10 false *B
*A LH *B RH


K151504

K151505

K151506

K151507


f.

Before installing a new part, apply body sealer.

HINT:

Apply body sealer in an even, continuous bead.


K151513


g.

Weld the A to the vehicle side.

K151514N01
1.99,2.979 2.083,3.583 2.083,3.583 2.25,3.583 false 2.344,3.5 2.5,3.698 0.156,0.198 10 false A


h.

Apply adhesive (3MTM AutomixTM Panel Bonding Adhesive #8115).

HINT:
·

Do not apply adhesive around the plug welding points.

·

Minimize squeeze out in plug welding areas.



K151491C01
0,0 0,0 false
K108837

Adhesive - -



i.

Weld the A to the vehicle side.

K151515N01
4.052,2.865 4.25,3.5 4.25,3.5 4.417,3.5 false 4.5,3.417 4.656,3.615 0.156,0.198 10 false A


j.

Apply adhesive (3MTM AutomixTM Panel Bonding Adhesive #8115).

HINT:
·

Do not apply adhesive around the plug welding points.

·

Minimize squeeze out in plug welding areas.



K151489C01
0,0 0,0 false
K108837

Adhesive - -



k.

Weld the A to the vehicle side.

K151516N01
2.427,2.24 2.75,2.833 2.75,2.833 2.917,2.833 false 3.01,2.719 3.167,2.917 0.156,0.198 10 false A


l.

Before installing a new part, apply body sealer.

HINT:

Apply body sealer in an even, continuous bead.


K151509C01
0.167,0.167 0.479,0.365 0.313,0.198 10 false *A
*A LH - -



m.

Weld the floor side rail plate sub-assembly to the vehicle side.

K151510C01
3.885,0.958 4,0.333 4,0.333 4.167,0.333 false 0.188,0.167 0.5,0.323 0.313,0.156 10 false *A 4.219,0.26 4.531,0.417 0.313,0.156 10 false *1
*A LH - -
*1 FLOOR SIDE RAIL PLATE SUB-ASSEMBLY - -



n.

Before installing a new part, apply body sealer.

HINT:

Apply body sealer in an even, continuous bead.


K151511C01
0.167,0.177 0.479,0.333 0.313,0.156 10 false *A
*A RH - -



o.

Weld the floor side rail plate to the vehicle side.

K151512C01
3.208,1.156 3,0.417 3,0.417 2.833,0.417 false 0.167,0.177 0.479,0.333 0.313,0.156 10 false *A 2.646,0.333 2.958,0.49 0.313,0.156 10 false *1
*A RH - -
*1 FLOOR SIDE RAIL PLATE - -



p.

After welding, apply body sealer and undercoating to the corresponding parts. (See the painting/coating)


q.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.