Home › Vehicle Exterior › BODY PANEL › CENTER BODY PILLAR (for 5 Door) › 2019.02–2019.06
BM35X0E _01 Vehicle Exterior _080418 BODY PANEL _0391626 CENTER BODY PILLAR(for 5 Door) F

BODY PANEL  CENTER BODY PILLAR(for 5 Door)  CUT AND JOIN REPLACEMENT SECTIONS  


K151887

REMOVAL


Symbol Meaning
K108818

Remove Weld Points
K108827

Cut and Join Location

a.

Do not butt weld or heat repair because the heat decreases the strength of areas where ultra high strength steel is used. (See the introduction)


b.

Roughly cut open the panel so that the adhesive can be reached. Cut through the adhesive with a cut chisel to remove the panel.

HINT:

In cases where the adhesive cannot be removed with a cut chisel, heat the adhesive with an industrial heater gun or gas burner taking care not to cause panel deformation by overheating.


K151767C01
0.167,0.167 0.479,0.365 0.313,0.198 10 false *A
*A LH - -
K108837

Adhesive - -



c.

Remove the front side panel outer and rocker panel outer rear.

K151254C01
5.083,0.833 7,3.5 1.917,2.667 1.76,5.417 1.927,5.417 1.927,5.417 1.979,4.625 false 4,5.427 3.833,5.427 3.833,5.427 3.75,4.625 false 0.188,0.167 0.5,0.323 0.313,0.156 10 false *A 4.083,5.333 4.396,5.49 0.313,0.156 10 false *2 2.615,1.219 2.927,1.375 0.313,0.156 10 false *a 4.802,4.844 5.115,5 0.313,0.156 10 false *c 1.583,5.333 1.896,5.49 0.313,0.156 10 false *1 1.521,3.865 1.833,4.021 0.313,0.156 10 false *b 5.167,0.927 5.479,1.083 0.313,0.156 10 false *B
*A LH *B for High Roof
*1 FRONT SIDE PANEL OUTER *2 ROCKER PANEL OUTER REAR
*a 155 mm (6.10 in.) *b 35 mm (1.38 in.)
*c 615 mm (24.21 in.) - -


K151255C01
0.167,0.167 0.479,0.323 0.313,0.156 10 false *A
*A LH - -


K151552C01
0.167,0.167 0.479,0.323 0.313,0.156 10 false *A
*A LH - -



d.

Remove the A.

HINT:

A is reused.


K151256C01
3.833,3.417 3.667,3.417 3.667,3.417 3.708,2.5 false 0.167,0.177 0.479,0.333 0.313,0.156 10 false *A 3.344,1.552 3.656,1.708 0.313,0.156 10 false *a 3.917,3.333 4.229,3.49 0.313,0.156 10 false A
*A LH - -
*a 115 mm (4.53 in.) - -



e.

Roughly cut open the panel so that the adhesive can be reached. Cut through the adhesive with a cut chisel to remove the panel.

HINT:

In cases where the adhesive cannot be removed with a cut chisel, heat the adhesive with an industrial heater gun or gas burner taking care not to cause panel deformation by overheating.


K151768C01
0.167,0.167 0.479,0.365 0.313,0.198 10 false *A
*A LH
K108837

Adhesive - -



f.

Remove the center body pillar reinforce sub-assembly upper.

K151257C01
3,2.167 3.167,2.167 3.167,2.167 3.708,2.458 false 0.167,0.167 0.479,0.323 0.313,0.156 10 false *A 2.823,2.083 3.135,2.24 0.313,0.156 10 false *1
*A LH - -
*1 CENTER BODY PILLAR REINFORCE SUB-ASSEMBLY UPPER - -



g.

Remove the center body pillar inner.

K151258C01
3.167,2.5 3.333,2.5 3.333,2.5 3.771,3.01 false 0.167,0.167 0.479,0.323 0.313,0.156 10 false *A 3,2.427 3.313,2.583 0.313,0.156 10 false *1 3.49,1.625 3.802,1.781 0.313,0.156 10 false *a
*A LH - -
*1 CENTER BODY PILLAR INNER - -
*a 170 mm (6.69 in.) - -



h.

Roughly cut open the panel so that the adhesive can be reached. Cut through the adhesive with a cut chisel to remove the panel.

HINT:

In cases where the adhesive cannot be removed with a cut chisel, heat the adhesive with an industrial heater gun or gas burner taking care not to cause panel deformation by overheating.


K151769C01
0.167,0.167 0.479,0.365 0.313,0.198 10 false *A
*A RH - -
K108837

Adhesive - -



i.

Remove the front side panel outer and rocker panel outer rear.

K151260C01
4.333,5.583 4.167,5.583 4.167,5.583 4.406,4.927 false 2.5,5.583 2.667,5.583 2.667,5.583 2.625,4.927 false 0.167,0.167 0.479,0.323 0.313,0.156 10 false *A 4.396,5.51 4.708,5.667 0.313,0.156 10 false *1 2.333,5.5 2.646,5.656 0.313,0.156 10 false *2 3.656,1.542 3.969,1.698 0.313,0.156 10 false *a 1.469,5.188 1.781,5.344 0.313,0.156 10 false *c 4.708,4.177 5.021,4.333 0.313,0.156 10 false *b
*A RH - -
*1 FRONT SIDE PANEL OUTER *2 ROCKER PANEL OUTER REAR
*a 155 mm (6.10 in.) *b 35 mm (1.38 in.)
*c 615 mm (24.21 in.) - -


K151259C01
0.167,0.167 0.479,0.323 0.313,0.156 10 false *A
*A RH - -


K151774C01
0.167,0.167 0.479,0.365 0.313,0.198 10 false *A
*A RH - -



j.

Remove the A.

HINT:

A is reused.


K151773C01
3.25,3.417 3.417,3.417 3.417,3.417 3.521,2.5 false 0.167,0.167 0.479,0.323 0.313,0.156 10 false *A 3.688,1.51 4,1.667 0.313,0.156 10 false *a 3.083,3.333 3.396,3.49 0.313,0.156 10 false A
*A RH - -
*a 115 mm (4.53 in.) - -



k.

Roughly cut open the panel so that the adhesive can be reached. Cut through the adhesive with a cut chisel to remove the panel.

HINT:

In cases where the adhesive cannot be removed with a cut chisel, heat the adhesive with an industrial heater gun or gas burner taking care not to cause panel deformation by overheating.


K151770C01
0.167,0.177 0.479,0.333 0.313,0.156 10 false *A
*A RH - -
K108837

Adhesive - -



l.

Remove the center body pillar reinforce sub-assembly upper.

K151261C01
4.5,2 4.333,2 4.333,2 3.698,2.438 false 0.167,0.167 0.479,0.323 0.313,0.156 10 false *A 4.583,1.927 4.896,2.083 0.313,0.156 10 false *1
*A RH - -
*1 CENTER BODY PILLAR REINFORCE SUB-ASSEMBLY UPPER - -



m.

Remove the center body pillar inner.

K151262C01
3.917,2.417 3.75,2.417 3.75,2.417 3.396,2.99 false 0.167,0.167 0.479,0.323 0.313,0.156 10 false *A 3.99,2.354 4.302,2.51 0.313,0.156 10 false *1 3.49,1.625 3.802,1.781 0.313,0.156 10 false *a
*A RH - -
*1 CENTER BODY PILLAR INNER - -
*a 170 mm (6.69 in.) - -




INSTALLATION


Symbol Meaning
K108823

Plug Weld
K108831

Butt Weld

a.

Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.


b.

Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimensions)


c.

Weld the center body pillar inner to the vehicle side.

K151263C01
4.083,5.417 6.75,8.417 2.667,3 3.729,2.177 3.333,1.583 3.333,1.583 3.167,1.583 false 4.021,3.135 4.667,2.667 4.667,2.667 4.833,2.667 false 5.406,6.573 6.083,6.083 6.083,6.083 6.25,6.083 false 5.396,6.927 6.083,6.083 false 0.167,0.177 0.479,0.333 0.313,0.156 10 false *A 4.167,5.51 4.479,5.667 0.313,0.156 10 false *B 2.979,1.51 3.292,1.667 0.313,0.156 10 false *1 4.906,2.594 5.219,2.75 0.313,0.156 10 false *2 6.333,6.01 6.646,6.167 0.313,0.156 10 false *3
*A LH *B w/ Assist Grip
*1 CENTER BODY PILLAR INNER *2 PILLAR SEAT BELT ANCHOR
*3 PILLAR ASSIST GRIP BRACKET LOWER - -



d.

Apply adhesive (3MTM AutomixTM Panel Bonding Adhesive #8115).

HINT:
·

Do not apply adhesive around the plug welding points.

·

Minimize squeeze out in plug welding areas.



K151768C01
0.167,0.167 0.479,0.365 0.313,0.198 10 false *A
*A LH
K108837

Adhesive - -



e.

Weld the center body pillar reinforce sub-assembly upper to the vehicle side.

K151264C01
2.833,2.083 3,2.083 3,2.083 3.698,2.458 false 0.167,0.177 0.479,0.333 0.313,0.156 10 false *A 2.656,2.01 2.969,2.167 0.313,0.156 10 false *1
*A LH - -
*1 CENTER BODY PILLAR REINFORCE SUB-ASSEMBLY UPPER - -



f.

Weld the A to the vehicle side.

K151265C01
3.5,3.417 3.667,3.417 3.667,3.417 3.708,2.49 false 0.167,0.177 0.479,0.333 0.313,0.156 10 false *A 3.344,3.344 3.656,3.5 0.313,0.156 10 false A
*A LH - -



g.

Apply adhesive (3MTM AutomixTM Panel Bonding Adhesive #8115).

HINT:
·

Do not apply adhesive around the plug welding points.

·

Minimize squeeze out in plug welding areas.



K152254C01
0.167,0.167 0.479,0.365 0.313,0.198 10 false *A
*A LH - -
K108837

Adhesive - -



h.

Weld the front side panel outer and rocker panel outer rear to the vehicle side.

K151266C01
5.083,0.833 6.917,3.5 1.833,2.667 1.75,5.427 1.917,5.427 1.917,5.427 1.979,4.625 false 3.99,5.406 3.823,5.406 3.823,5.406 3.75,4.615 false 0.188,0.167 0.5,0.323 0.313,0.156 10 false *A 1.594,5.354 1.906,5.51 0.313,0.156 10 false *1 4.052,5.313 4.365,5.469 0.313,0.156 10 false *2 5.167,0.917 5.479,1.073 0.313,0.156 10 false *B
*A LH *B for High Roof
*1 FRONT SIDE PANEL OUTER *2 ROCKER PANEL OUTER REAR


K151267C01
0.167,0.167 0.479,0.323 0.313,0.156 10 false *A
*A LH - -


K152089C01
2.833,0.5 3,0.5 3,0.5 3.271,1.01 false 3.802,0.76 4.583,0.25 4.583,0.25 4.75,0.25 false 3.698,1.958 4.583,0.25 false 0.167,0.177 0.479,0.333 0.313,0.156 10 false *A 2.604,0.427 2.917,0.583 0.313,0.156 10 false *1 4.833,0.177 5.146,0.333 0.313,0.156 10 false *2
*A LH - -
*1 FUEL FILLER OPENING LID ASSEMBLY *2 RIVETS



i.

Weld the center body pillar inner to the vehicle side.

K151268C01
4.083,5.417 6.75,8.417 2.667,3 3.156,3.333 2.417,2.667 2.417,2.667 2.25,2.667 false 3.469,2.396 4.115,1.927 4.115,1.927 4.281,1.927 false 5.229,6.604 4.667,6.167 4.667,6.167 4.5,6.167 false 5.229,6.948 4.667,6.167 false 0.167,0.177 0.479,0.333 0.313,0.156 10 false *A 4.167,5.51 4.479,5.667 0.313,0.156 10 false *B 4.354,1.844 4.667,2 0.313,0.156 10 false *1 2.052,2.594 2.365,2.75 0.313,0.156 10 false *2 4.323,6.083 4.635,6.24 0.313,0.156 10 false *3
*A RH *B w/ Assist Grip
*1 CENTER BODY PILLAR INNER *2 PILLAR SEAT BELT ANCHOR
*3 PILLAR ASSIST GRIP BRACKET LOWER - -



j.

Apply adhesive (3MTM AutomixTM Panel Bonding Adhesive #8115).

HINT:
·

Do not apply adhesive around the plug welding points.

·

Minimize squeeze out in plug welding areas.



K151770C01
0.167,0.177 0.479,0.333 0.313,0.156 10 false *A
*A RH - -
K108837

Adhesive - -



k.

Weld the center body pillar reinforce sub-assembly upper to the vehicle side.

K151269C01
3.698,2.427 4,2 4,2 4.167,2 false 0.188,0.167 0.5,0.323 0.313,0.156 10 false *A 4.25,1.927 4.563,2.083 0.313,0.156 10 false *1
*A RH - -
*1 CENTER BODY PILLAR REINFORCE SUB-ASSEMBLY UPPER - -



l.

Weld the A to the vehicle side.

K151270C01
3.302,3.427 3.469,3.427 3.469,3.427 3.51,2.5 false 0.167,0.177 0.479,0.333 0.313,0.156 10 false *A 3.167,3.333 3.479,3.49 0.313,0.156 10 false A
*A RH - -



m.

Apply adhesive (3MTM AutomixTM Panel Bonding Adhesive #8115).

HINT:
·

Do not apply adhesive around the plug welding points.

·

Minimize squeeze out in plug welding areas.



K152255C01
0.167,0.167 0.479,0.365 0.313,0.198 10 false *A
*A RH - -
K108837

Adhesive - -



n.

Weld the front side panel outer and rocker panel outer rear to the vehicle side.

K151271C01
4.083,5.583 4.25,5.583 4.25,5.583 4.396,4.938 false 2.313,5.583 2.479,5.583 2.479,5.583 2.625,4.938 false 0.167,0.177 0.479,0.333 0.313,0.156 10 false *A 3.917,5.51 4.229,5.667 0.313,0.156 10 false *1 2.156,5.5 2.469,5.656 0.313,0.156 10 false *2
*A RH - -
*1 FRONT SIDE PANEL OUTER *2 ROCKER PANEL OUTER REAR


K151775C01
0.167,0.167 0.479,0.323 0.313,0.156 10 false *A
*A RH - -



o.

After welding, apply the foamed sealing material to the corresponding parts. (See the painting/coating)


p.

After welding, apply body sealer to the corresponding parts. (See the painting/coating)


q.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.