With the rear floor rear inner crossmember cut and join replacement sections (small areas) removed.
REMOVAL
| Symbol Meaning | |
|---|---|
|
Remove Weld Points |
|
Cut and Join Location |
|
Cut Location |
Remove the rear floor panel rear.
| *A | for Standard Roof | - | - |
| *1 | REAR FLOOR PANEL REAR | - | - |
| *a | 575 mm (22.64 in.) | - | - |
| *A | for High Roof | *B | for Space Up Seat |
| *1 | REAR FLOOR PANEL REAR | - | - |
| *a | 575 mm (22.64 in.) | - | - |
| *A | for High Roof | *B | except Space Up Seat |
| *1 | REAR FLOOR PANEL REAR | - | - |
| *a | 575 mm (22.64 in.) | - | - |
| *A | LH Side | *B | RH Side |
Remove the front side member plate No.7 and floor plate rear to the vehicle side.
| *A | for Space Up Seat | *B | LH Side |
| *C | RH Side | - | - |
| *1 | FRONT SIDE MEMBER PLATE NO.7 | *2 | FLOOR PLATE REAR |
| *a | 50 mm (1.97 in.) | - | - |
| *A | except Space Up Seat | *B | LH Side |
| *C | RH Side | - | - |
| *1 | FRONT SIDE MEMBER PLATE NO.7 | *2 | FLOOR PLATE REAR |
| *a | 50 mm (1.97 in.) | - | - |
INSTALLATION
| Symbol Meaning | |
|---|---|
|
Plug Weld |
|
Cut and Join Location |
|
Cut Location |
|
Butt Weld |
|
Body Sealer |
Cut the new part so that it overlaps the previous cut location by approximately 30 mm (1.18 in.).
| *A | Upper Face | - | - |
| *1 | REAR FLOOR PANEL REAR | - | - |
| *a | 545 mm (21.46 in.) | - | - |
Before temporarily installing the new parts, weld the rear floor panel rear and sub floor leg base No.2 with the standard number of welding points.
| *A | Lower Face | - | - |
| *1 | REAR FLOOR PANEL REAR | *2 | SUB FLOOR LEG BASE NO.2 |
Before temporarily installing the new parts, weld the rear floor panel rear and extinguisher bracket No.1 with the standard number of welding points.
| *A | Upper Face | *B | w/ Extinguisher Bracket No.1 |
| *1 | REAR FLOOR PANEL REAR | *2 | EXTINGUISHER BRACKET NO.1 |
Before temporarily installing the new parts, weld the front side member plate No.7 and floor plate rear with the standard number of welding points.
| *1 | FRONT SIDE MEMBER PLATE NO.7 | *2 | FLOOR PLATE REAR |
| *a | 40 mm (1.57 in.) | - | - |
Weld the front side member plate No.7 and floor plate rear to the vehicle side.
| *A | for Space Up Seat | *B | LH Side |
| *C | RH Side | - | - |
| *1 | FRONT SIDE MEMBER PLATE NO.7 | *2 | FLOOR PLATE REAR |
| *A | except Space Up Seat | *B | LH Side |
| *C | RH Side | - | - |
| *1 | FRONT SIDE MEMBER PLATE NO.7 | *2 | FLOOR PLATE REAR |
Weld the rear floor panel rear to the vehicle side.
Perform plug-welding in the area where the panel are overlapped. Apply body sealer to each panel.
Confirm that the panels are securely welded together.
Apply body sealer in an even, continuous bead.
| *A | for Standard Roof | - | - |
| *1 | REAR FLOOR PANEL REAR | - | - |
| *A | for High Roof | *B | for Space Up Seat |
| *1 | REAR FLOOR PANEL REAR | - | - |
| *A | for High Roof | *B | except Space Up Seat |
| *1 | REAR FLOOR PANEL REAR | - | - |
| *A | LH Side | *B | RH Side |
After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.
After welding, apply body sealer and undercoating to the corresponding parts. (See the painting/coating)